I-ARDUINO RFLINK-Hlanganisa i-UART engenantambo ku-I2C Module

I-RFLINK-Mix Wireless UART-to-I2C iyisuite engenantambo evumela abasebenzisi ukuthi bamise ngokushesha amadivayisi e-I2C. Awudingi ukuxhuma izintambo eziningi ezinde ukusuka embobeni yokusingatha ye-I2C ukuya kumadivayisi e-I2C ngayinye ngayinye. Udinga kuphela ukuxhuma i-UART ROOT ye-RFLINK-Mix kusixhumi esibonakalayo se-UART sokulawula okuyinhloko (i-Arduino, i-Raspberry Pi, noma iyiphi enye i-HOST) , kanye namadivayisi we-I2C SLAVE ku-RFLINK-Mix ohlangothini lwe-I2C Master, i-UART- engenantambo isistimu ye-to-I2C isilungele ukuhamba.

Ukubukeka kwemojuli nobukhulu

Imojula ye-RFLINK-Mix UART-to-I2C iqukethe ucezu olulodwa lwe-UART ROOT (kwesokunxele) nezingcezu ezifika kwezine Uhlangothi lwedivayisi ye-I2C (imojula ye-RFLINK-Mix I2C i-Master–uhlangothi lwesokudla lwesibalo esingezansi, olunezinombolo ezingu-0 ~ 3). Ukubukeka kwezinhlobo ezimbili kuyafana, kodwa kungabonakala ngebhokisi lokuhlola lelebula elingemuva .
Njengoba kuboniswe esithombeni esingezansi, isibalo esingakwesokunxele siwuhlangothi lwengxenye, kanti ezinye ziwuhlangothi lwelebula Ikheli Leqembu laleli qembu lamamojula e-RFLINK-UART ROOT lithi 0001, izinga le-baud 19200. I-RFLINK I2C Idivayisi iyidivayisi 0 (CLK 1.4 M), Idivayisi 1 (CLK 400K), Idivayisi 2 (CLK 400K), Idivayisi 3 (CLK 100K). , ikheli leqembu ngu-0001, Iwashi lingakhethwa ngesikhathi sokuthenga

Izici zemojuli

1. I-vol esebenzayotage: 3.3 ~ 5.5V
2. Imvamisa ye-RF: 2400MHz ~ 2480MHz.
3. Ukusetshenziswa kwamandla: 24 mA@ +5dBm kumodi ye-TX kanye no-23mA kumodi ye-RX.
4. Amandla okudlulisa: +5dBm
5. Ibanga lokudlulisela: cishe 80 kuya ku-100m endaweni evulekile
6. I-Baud Rate(UART ROOT):9,600bps noma 19,200bps
7. Iwashi(I2C MASTER) : 1.2M/750K/400K/200K/100K/50K/25K/12.5K. (Okuzenzakalelayo 400K)
8. Ubukhulu: 25 mm x 15 mm x 2 mm (LxWxH)
9. Isekela ukudluliselwa oku-1 kuya koku-1 noma koku-1 kuya kokuningi (kufika kokune), futhi isetshenziswa kumodi yomyalo uma isetshenziswa i-Command 1-to-multiple khetha ukuthi iyiphi idivayisi ozothumela ngayo. .

Phina incazelo yephinikhodi

UART ROOT

I-I2C IDIVAYISI

GNDe Ground +5Veya 5vtage input I-TXè ihambisana ne-RX ye-motherboard UART Idatha ye-RXè ihambisana ne-TX ye-motherboard UART I-CEBè Le CEB kufanele ixhumeke phansi (GND), bese imojuli izovuleka futhi ingasetshenziswa njengomsebenzi wokulawula ukonga amandla. PHUMAè Iphinikhodi yokuphuma ye-IO Port (Vuliwe/Vala ukuthumela) INèInput pin ye-IO Port (Vuliwe/Valiwe thola).

GNDe Ground +5Veya 5vtage input Idatha ye-SCLè ihambisana ne-SCL (Serial Clock Line serial clock) yedivayisi ye-I2C Slave I-SDAè ihambisana ne-SDA (Serial Data Line Serial Data Line) kudivayisi ye-I2C Slave I-CEBè Le CEB kufanele ixhumeke phansi (GND), bese imojuli izovuleka futhi ingasetshenziswa njengomsebenzi wokulawula ukonga amandla. PHUMAè Iphinikhodi yokuphuma ye-IO Port (On/Off the export)

Isetshenziswa kanjani

Le mojula isekela imojuli ye-Liquid Crystal I2C LCD, elawula amasethi amaningi ama-LCD ngokusebenzisa isixhumi esibonakalayo sokuxhumana se-UART.

Ungalanda lesi sibonelo sokusetshenziswa se-RFLINK-Mix UART-to-I2Cample kwisikhulu webindawo http://www.sunplusit.com/TW/Shop/IoT/Document.

Amadokhumenti / Izinsiza

	I-ARDUINO RFLINK-Hlanganisa i-UART engenantambo ku-I2C Module [pdf] Imaniwali yosebenzisayo I-RFLINK-Mix, i-UART engenantambo ukuya ku-I2C Module, RFLINK-Hlanganisa i-UART engenantambo ku-I2C Module
	I-ARDUINO RFLINK-Hlanganisa i-UART engenantambo ku-I2C Module [pdf] Imaniwali yosebenzisayo I-RFLINK-Mix Wireless UART to I2C Module, Mix Wireless UART to I2C Module, Wireless UART to I2C Module, UART to I2C Module, I2C Module, Module

Izithenjwa

• Imaniwali yosebenzisayo