ZEBRA ZD421 Desktop Printer
Product Specifications
- Model: ZD421D
- Type: Desktop Printer
- Connectivity: USB
- Media: Not included
Product Usage Instructions:
Setup:
Visit zebra.com/zd421d-info and install the driver for your printer.
Remove Packing:
Extraer embalaje / Retirer l’emballage
Load Media:
- Verify the roll spins easily on the holder.
- Despliegue los soportes del rollo y coloque el rollo en la impresora.
- Assurez-vous que le rouleau tourne facilement.
Connect Power and USB:
- Connect the power cable.
- Connect the USB cable.
- Power on the printer by pressing the POWER button.
Support and Information:
- For support, visit zebra.com/supportcommunity
- For supplies, visit zebra.com/supplies
- Contact Zebra at zebra.com/contactsupport
Cleaning:
Regularly clean the printer to maintain optimal performance.
Frequently Asked Questions (FAQ)
- Is media included with the ZD421D printer?
No, media is not included with the printer. You will need to purchase media separately. - How do I find product patent information?
Visit zebra.com/patents to learn more about product patent information.
Setup
IMPORTANT
Go to zebra.com/zd421d-info and install the driver for your printer.
The driver MUST be installed before connecting the printer to the computer, or it will cause complications. If your Microsoft Windows-based computer does not have the driver installed for this printer, download it from zebra.com/zd421d-info and install it before continuing.
Remove Packing
- After unpacking, make sure you have all items shown below.
- Slide the release latches (1) to the front to unlock the cover.
- Open the printer and remove the packing (1).
Load Media
- Unroll (1) and discard (2) the outer layer of the media roll (3).
- Spread the roll holders open (1) and place the roll (2) into the printer.
- Verify the roll spins easily on the holder.
- Pull the end of the roll past the front edge of the printer.
- Press the media under the guides (1).
Adjust Sensor
- Align the sensor to the center of the roll for regular labels (1).
- Align the sensor to the edge of the roll for marked labels (1).
Close Printer
Push down on the front edge of the printer until it locks.
Connect Power
- Plug the power supply into the printer.
- Plug the power cable into the power supply.
- Plug the power cord into an appropriate receptacle.
- Verify that the power supply lights green.
Connect USB
- Connect a USB cable to the printer.
- Connect the other end to your computer.
Power On
- Press POWER (1).
- When the the printer is ready, the printer status light turns green (1).
Smart Calibration
Press and hold PAUSE (1) + CANCEL (2) for two seconds to line up the labels.
Print Configuration
Press and hold FEED (1) + CANCEL (2) for two seconds to print a configuration report.
Support and Information
- View user documentation. zebra.com/zd421d-info
- Need to design a label? zebra.com/zebradesigner
- Learn about genuine Zebra supplies. zebra.com/supplies
- Need to manage your printer? zebra.com/profilemanager
- View Quick Answers and Knowledge Base. zebra.com/knowledge
- Join Community Connection of Zebra users and ambassadors. zebra.com/supportcommunity
- Contact Zebra about your printer. zebra.com/contactsupport
- Need to secure your printer? zebra.com/printsecure
- Learn about product patent information. ip.zebra.com
Media Out
- When the media runs out, the printer status and media status lights will turn red (1).
- Open the printer and discard the empty roll (1).
Cleaning
Clean the printhead (1) with a cleaning pen (2). Clean from the middle to the outside. Do not use a cleaning pen on the platen.
Documents / Resources
 |
ZEBRA ZD421 Desktop Printer [pdf] User Guide ZD421, ZD421D, ZD421 Desktop Printer, ZD421, Desktop Printer, Printer |