ZEBRA MC2700 Rugged Handheld Mobile Computers User Guide
Regulatory Information
This device is approved under Zebra Technologies Corporation.
This guide applies to the following model numbers:
- MC27AK
- MC27BK
- MC27AJ
- MC27BJ
- MC27CK
- MC27CJ
All Zebra devices are designed to be compliant with the rules and regulations in the locations they are sold and will be labeled as required.
authority to operate the equipment
CAUTION: Only use Zebra approved and NRTL-certified accessories, battery packs, and battery chargers. Do NOT attempt to charge damp/wet mobile computers, printers or batteries. All components must be dry before connecting to an external power source.www.bluetooth.com.
workplace practices. Consult with your local Health and Safety Manager to ensure that you are adheringto your company’s safety programs to prevent employee injury.
Vehicle Installation
RF signals may affect improperly installed or inadequately shielded electronic systems in motor vehicles (including safety systems). Check with the manufacturer or its representative regarding your vehicle. Ensure the equipment is installed to avoid driver distractions. You should also consult the manufacturer about any equipment that has been added to your vehicle.
Position the device within easy reach. User should be able to access the device without removing their eyes from the road.
IMPORTANT: Before installing or using, check national and local laws regarding distracted driving.
Give your full attention to driving. Obey the laws and regulations on the use of wireless devices in the
areas where you drive.
Remember to observe restrictions and obey all signs and instructions on the use of electronic devices in
restricted use locations.
NOTE: Wireless devices transmit radio frequency energy that may affect medical electrical equipment and aircraft’s operation. Wireless devices should be switched off wherever you are requested to do so in hospitals, clinics, healthcare facilities or by airline staff. These requests are designed to prevent possible interference with sensitive equipments.It is recommended that a minimum separation distance of 20 cm (8 inches) be maintained between a
wireless device and a medical devices such as pacemakers, defibrillator, or other implantable devices to
avoid potential interference with the medical device. Pacemaker users should keep the device at the opposite side of the pacemaker or turn OFF the device if suspected of interference.
your wireless product may interfere with the medical device.
Safety Information
Reducing RF Exposure – Use Properly
Only operate the device in accordance with the instructions supplied.
electromagnetic fields. For information on international human exposure to electromagnetic fields, refer to the Zebra Declaration of Conformity (DoC) at www.zebra.com/doc
compliance requirements and should be avoided.
Classified as ‘EXEMPT RISK GROUP’ according to IEC 62471:2006 and EN 62471:2008.
Pulse Duration: 22.8 ms or CW (MC2700 with SE4100)
WARNING ELECTRICAL SHOCK: Use only a Zebra approved, Certified ITE [LPS] power supply
with appropriate electrical ratings. Use of alternative power supply will invalidate any approvals
given to this unit and may be dangerous.
This information applies to Zebra-approved batteries and power packs containing batteries.
- Model BT-000418 (3.6 VDC, 3300 mAh)
- Model BT-000432 (3.6 VDC, 4900 mAh)
Zebra approved rechargeable battery packs are designed and constructed to the highest standards within
the industry.
However, there are limitations as to how long a battery can operate or be stored before needing
replacement. Many factors affect the actual life cycle of a battery pack such as heat, cold, harsh environmental conditions, and severe drops.
When batteries are stored over six months, some irreversible deterioration in overall battery quality may
occur. Store batteries at half charge in a dry, cool place, removed from the equipment to prevent loss of
capacity, rusting of metallic parts, and electrolyte leakage. When storing batteries for one year or longer,
the charge level should be verified at least once a year and charged to half charge.
Replace the battery when a significant loss of run time is detected.
- Standard warranty period for all Zebra batteries is one year, regardless if the battery was purchased separately or included as part of the host device. For more information on Zebra batteries, please visit: www.zebra.com/batterydocumentation and select the Battery Best Practices link.
Battery Safety Guidelines
IMPORTANT – SAFETY INSTRUCTIONS – SAVE THESE INSTRUCTIONS
WARNING – When using this product basic safety precautions should always be followed, including the following:
The area in which the units are charged should be clear of debris and combustible materials or chemicals. Particular care should be taken where the device is charged in a non-commercial environment.
- Read all the instructions before using the product.
- Follow battery usage, storage, and charging guidelines found in the user’s guide.
- Improper battery use may result in a fire, explosion, or other hazard.
To charge the mobile device battery, the battery and charger temperatures must be between 0°C and +40°C (+32°F and +104°F).
Do not use incompatible batteries and chargers. Use of an incompatible battery or charger may present a
risk of fire, explosion, leakage, or other hazard. If you have any questions about the compatibility of a battery or a charger, contact Zebra support.
Do not disassemble or open, crush, bend or deform, puncture, or shred. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion, or risk of injury.
Severe impact from dropping any battery-operated device on a hard surface could cause the battery to overheat.
Do not short circuit a battery or allow metallic or conductive objects to contact the battery terminals.
Do not modify, disassemble, or remanufacture, attempt to insert foreign objects into the battery, immerse or expose to water, rain, snow or other liquids, or expose to fire, explosion, or other hazard.
Do not leave or store the equipment in or near areas that might get very hot, such as in a parked vehicle or near a radiator or other heat source. Do not place battery into a microwave oven or dryer.
To reduce the risk of injury, close supervision is necessary when used near children.
Please follow local regulations to promptly dispose of used re-chargeable batteries.
Do not dispose of batteries in fire. Exposure to temperatures over 100°C (212°F) may cause explosion.
Seek medical advice immediately if a battery has been swallowed.
In the event of a battery leak, do not allow the liquid to come in contact with the skin or eyes. If contact has been made, wash the affected area with large amounts of water and seek medical advice.
If you suspect damage to your equipment or battery, contact Zebra support to arrange for inspection.
Marking and European Economic Area (EEA) Zebra hereby declares that this radio equipment is in compliance with Directives 2014/53/EU and 2011/65/EU.
Conformity. The full text of the EU Declaration of Conformity is available at: www.zebra.com/doc.
For EU Customers: For products at the end of their life, please refer to recycling/disposal advice at:
www.zebra.com/weee.
United States and Canada Regulatory
Radio Frequency Interference Notices
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digitaldevice, pursuant to Part 15 of the FCC rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
Radio Frequency Interference Requirements – Canada
Innovation, Science and Economic Development Canada ICES-003 Compliance Label: CAN ICES-3
([B])/NMB-3([B]
This device complies with Innovation, Science and Economic Development Canada’s licence-exempt
RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device.
RF Exposure Requirements – FCC and ISED
The FCC has granted an Equipment Authorization for this device with all reported SAR levels evaluated in compliance with the FCC RF emission guidelines. SAR information on this device is on file with the FCC and can be found under the Display Grant section of www.fcc.gov/oet/ea/fccid.
Handheld Devices
To satisfy RF exposure requirements, this device must operate with a minimum separation distance of 1
cm or more from a user’s body and nearby persons.p
Pour satisfaire aux exigences d’exposition aux radio fréquences, cet appareil doit fonctionner avec une
distance de séparation minimale de 1 cm ou plus de corps d’une personne.
To comply with FCC RF exposure compliance requirement, the antenna used for this transmitter must not be co-located (within 20 cm) or operating in conjunction with any other transmitter/antenna except those already approved in this filling.
When operating in hotspot mode, this device is restricted to indoor use when operating in the 5150 – 5350 MHz frequency range.
Underwriters Laboratories Inc. (UL) has not tested the performance or reliability of the Global Positioning System (GPS) hardware, operating software, or other aspects of this product. UL has only tested for fire, shock, or casualties as outlined in UL’s Standard(s) for Safety for Information Technology Equipment. UL Certification does not cover the performance or reliability of the GPS hardware and GPS operating software. UL makes no representations, warranties, or certifications whatsoever regarding the
performance or reliability of any GPS related functions of this product
Oriya, Punjabi, Sanskrit, Sindhi, Tamil, Telugu, Urdu, Bodo, Santhali, Maithili, and Dogri.
Warranty
For the complete Zebra hardware product warranty statement, go to: zebra.com\warranty.
Service Information
Before you use the unit, it must be configured to operate in your facility’s network and run your
applications. If you have a problem running your unit or using your equipment, contact your facility’s
Technical or System Support. If there is a problem with the equipment, they will contact Zebra support at
zebra.com\support. For the latest version of the guide go to: zebra.com\support.
Additional Information
For information on using the MC2700, refer to the MC2700 product guide available at: zebra.com/support.
Documents / Resources
 |
ZEBRA MC2700 Rugged Handheld Mobile Computers [pdf] User Guide MC2700 Rugged Handheld Mobile Computers, MC2700, Rugged Handheld Mobile Computers, Handheld Mobile Computers, Mobile Computers, Computers |
