ZALMAN Z3 Iceberg ATX Mid Tower Computer Case User Manual

RAZER CHROMA can be compatible with Z3 ICEBERG through Z-Sync or H/W supported

• To ensure safe and easy installation, please read the following precautions.
• Product design and specifications may be revised to improve quality and performance without notice.

Precautions

• Read this manual carefully before installing.
• Check the product and components before installing. If you find any abnormality, contact the location where you purchased the product for a replacement or refund.
• Wear gloves to prevent accidents when installing the product.
• Severe damage may occur when mounting the system, so do not apply excessive force.
• Connecting the cable incorrectly may cause a fire due to a short circuit. Make sure to refer to the manual when connecting the cable.
• Be careful not to block the ventilation hole of the product when using the system.
• Avoid locations with direct sunlight, water, moisture, oil, and excessive dust. Store and use the product in a well-ventilated location.
• Do not wipe the surface of the product using chemicals. (organic solvents such as alcohol or acetone)
• Do not insert your hand or other object into the product during operation, as this may injure your hand or damage the object.
• Store and use the product out of children’s reach.
• Our company assumes no responsibility for any problem that occurs due to the use of the product for purposes other than its designated purposes and/or the carelessness of the consumer.
• The exterior design and specifications of the product are subject to change without prior notice to consumers for quality improvement.

Specifications

Model		Z3 Iceberg KOR	Z3 Iceberg
Case Form Factor		ATX Mid-Tower
Dimensions		410 x 210 x 480(H)mm
Weight		6.6kg	6.4kg
Case Materials		Plastic, Steel, Tempered Glass
Motherboard Support		E-ATX(~280mm) / ATX / mATX / Mini-ITX
Maximum VGA Length		315mm
Maximum CPU Cooler Height		163mm
Maximum PSU Length		160mm
PCI Expansion Slots		7
Drive Bays		2 x 3.5″ (2 x Combo, 1 x Toolless), 4 x 2.5″
Fan Support	Top	2 x 120mm / 2 x 140mm
	Front	3 x 120mm / 3 x 140mm
	Rear	1 x 120mm
Fan(s) Included	Front	3 x 120mm (with White LED Effect)	1 x 120mm (Addressable RGB)
	Rear	1 x 120mm (with White LED Effect)	1 x 120mm (Addressable RGB)
			ARGB Controller Included
Radiator Support	Top	120mm / 240mm
	Front	120mm / 240mm / 280mm / 360mm
	Rear	120mm
I/O Ports		1 x Headphone, 1 x Mic, 1 x USB 2.0, 2 x USB 3.0, Power Button, Reset Button, LED Button

Diminsion

Accessories component

• User’s Manual
  
• Buzzer
  
• PCI Slot Covers x 2
  
• Cable Ties x 5
  
• Glass Cleaner
  
• USB Rubber overs x 3
  
• Fan Screws x 6
  
• Media Rubber Covers x 2
  
• Thumb Screws x 2
  
• HDD Screws x 8
  
• SSD / MB Screws x 22
  
• PSU / VGA Screws x 8
  
• Motherboard Standoffs x 6
  

I/O Ports

#	Part	#	Part	#	Part	#	Part
⑥	Power Button	ⓑ	HDD / Power LED	ⓒ	Reset Button	ⓓ	USB 3.0 Ports
ⓔ	USB 2.0 Port	ⓕ	Headphone Jack	ⓖ	Microphone Jack	ⓗ	LED Button

How to control RGB LED

Caution : Please do not connect ARGB fans more than 8pcs, otherwise it may cause malfunction.

• LED colors & patterns can be changed by pressing the LED Button on I/O ports.
• Long pressing on the LED Button for 6 seconds, RGB LED will be turn off after blinking twice in white.
• Long pressing on the LED Button for 3 seconds, RGB will be synchronized with motherboard after blinking once in white. Press the LED Button again to desynchronize with motherboard.

1. (A) ARGB LED 1~4 / 3-Pin
   
2. (B) ARGB LED Control Button / 2-Pin
   • Connector to ARGB LED Control Button
3. (C) Other Motherboards Sync / 3-Pin
   • Connector to Motherboard
   • Requires Motherboard that Supports RGB Sync
     
     Caution: if Addressable 3 Pin connects to 12V header instead of 5V header improperly, It may cause fatal damages to the product by the overvoltage.
4. (D) SATA Power / 15-Pin
   • Connector to PSU
   • Input : 5V
     
5. (E) Connect the ARGB connector to the RGB hub

Removing the side panels

Removing the front panel

Mounting the motherboard

Motherboard size

1. E-ATX (~280mm)
   
2. ATX
   
3. mATX
   
4. Mini-ITX
   

Mounting PCI-E(VGA) card

Mounting the 2.5″ SSD

Mounting the 3.5″ and 2.5″ SSD / HDD

Mounting the PSU

Mounting the radiator

1. Mounting the front radiator
   • 120mm / 240mm / 280mm / 360mm
     
2. Mounting the top radiator
   • 120mm / 240mm
     
3. Mounting the rear radiator
   • 120mm
     

Mounting the fans

1. Mounting the top fans
   • 120mm x 2, 140mm x 2
     
2. Mounting the front fans
   • 120mm x 3, 140mm x 3
     
3. Mounting the rear/bottom fan
   • 120mm x 1 / 120mm x 2
     

Fan(s) Included / Fan Specifications

Z3 Iceberg

Addressable RGB LED Fan	Front / Rear
Dimensions	120 x 120 x 25(T)mm
RPM	1,300 ±15%
Fan	DC 12V 0.15A ±20%
LED	DC 5V 0.72A
Bearing	Hydro Bearing
Power Connector	Fan-3PIN

Z3 Iceberg KOR

Addressable RGB LED Fan	Front / Rear
Dimensions	120 x 120 x 25(T)mm
RPM	1,200 ±10%
Fan LED	DC 12V 0.27A ±20%
Bearing	Hydro Bearing
Power Connector	IDE-4PIN Fan-3PIN

I/O Connectors

Certification

This mark, designed by Zalman, indicates product compliance with the European Union’s RoHS (Restriction of Hazardous Substances) Directive.

Disposal of Old Electrical & Electronic Equipment (Applicable in the European Union and other European countries with separate collection systems)

 

Documents / Resources

	ZALMAN Z3 Iceberg ATX Mid Tower Computer Case [pdf] User Manual Z3 Iceberg, ATX Mid Tower Computer Case
	ZALMAN Z3 Iceberg ATX MID Tower Computer Case [pdf] User Manual Z3 Iceberg, ATX MID Tower Computer Case
	ZALMAN Z3 Iceberg ATX MID Tower Computer Case [pdf] User Manual Z3 Iceberg ATX MID Tower Computer Case, Z3 Iceberg, ATX MID Tower Computer Case, ATX Tower Computer Case, MTD Tower Computer Case, Computer Case, Tower Case, Case
	ZALMAN Z3 Iceberg ATX MID Tower Computer Case [pdf] User Manual Z3 Iceberg ATX MID Tower Computer Case, Z3 Iceberg, Z3, Iceberg, ATX MID Tower Computer Case, Tower Computer Case, ATX MID Computer Case, MID Computer Case, ATX Computer Case, Computer Case, Case

References

• User Manual