ZALMAN logoZALMAN X3 ATX Mid Tower ComputerZALMAN X3 ATX Mid Tower Computer Case product

Precautions

  • Read this manual carefully before installing.
  • Check the product and components before installing. If you find any abnormality, contact the location where you purchased the product for a replacement or refund.
  • Wear gloves to prevent accidents when installing the product.
  • Severe damage may occur when mounting the system, so do not apply excessive force.
  • Connecting the cable incorrectly may cause a fire due to a short circuit. Make sure to refer to the manual when connecting the cable.
  • Be careful not to block the ventilation hole of the product when using the system.
  • Avoid locations with direct sunlight, water, moisture, oil, and excessive dust. Store and use the product in a well-ventilated location.
  • Do not wipe the surface of the product using chemicals. (organic solvents such as alcohol or acetone)
  • Do not insert your hand or other object into the product during operation, as this may injure your hand or damage the object.
  • Store and use the product out of children’s reach.
  • Our company assumes no responsibility for any problem that occurs due to the use of the product for purposes other than its designated purposes and/or the carelessness of the consumer.
  •  The exterior design and specifications of the product are subject to change without prior notice to consumers for quality improvement.

Specifications

Model X3
Case Form Factor ATX Mid-Tower
Dimensions 430 x 210 x 459(H)mm
Weight 9.1kg
Case Materials Plastic, Steel, Tempered Glass
Motherboard Support ATX / mATX / Mini-ITX
Maximum VGA Length 350mm
Maximum CPU Cooler Height 175mm
Maximum PSU Length 180mm
PCI Expansion Slots 7
Drive Bays 1 x Combo (3.5” or 2.5″) or 1 x Combo (2 x 3.5″), 2 x 2.5”
 

Fan Support

Top 2 x 120mm, 2 x 140mm
Front 3 x 120mm, 2 x 140mm
Rear 1 x 120mm, 1 x 140mm
 

Pre-Installed Fan(s)

Front 3 x 120mm (with Addressable RGB LED Sync)
Rear 1 x 120mm (with Addressable RGB LED Sync)
 

Radiator Support

Front 120mm / 240mm / 280mm / 360mm
Rear 120mm
I/O Ports 2 x USB 3.0, 2 x USB 2.0, 1 x Headphone Jack, 1 x Microphone Jack, LED Control Button, Reset Button, Power Button

Caution (Radiator support)

280mm radiator can be problematic to install on the X3. Width of the radiator should be 140mm. If you wish to use a radiator larger than 140mm please be sure to check the distance between the side of the radiator to screw hole. If the distance is below 5.7mm you can install it to X3.ZALMAN X3 ATX Mid Tower Computer Case fig 1

AccessoriesZALMAN X3 ATX Mid Tower Computer Case fig 2

I/O PortsZALMAN X3 ATX Mid Tower Computer Case fig 3

# Part # Part # Part # Part
USB 3.0 Port USB 2.0 Port Microphone Jack LED Control Button
Headphone Jack USB 2.0 Port USB 3.0 Port Power Button

RGB(Addressable) LED Control Button

  1. Short Press : 1st ~ 50th RGB LED Lighting Mode (Effects & Colors)
  2. Long Press : RGB LED Lighting Mode Change (LED Control Button → Motherboard Sync (Addressable Sync) → Lighting Off)

Removing the side panelsZALMAN X3 ATX Mid Tower Computer Case fig 4

Mounting the motherboardZALMAN X3 ATX Mid Tower Computer Case fig 5

Motherboard sizeZALMAN X3 ATX Mid Tower Computer Case fig 6

Mounting the PSUZALMAN X3 ATX Mid Tower Computer Case fig 7

Mounting the PCI-E(VGA) cardZALMAN X3 ATX Mid Tower Computer Case fig 8

Graphics card holder

Install the graphics card brace to a convenient position.ZALMAN X3 ATX Mid Tower Computer Case fig 9

Mounting the 3.5″ and 2.5″ SSD / HDDZALMAN X3 ATX Mid Tower Computer Case fig 10

Mounting the 2.5” SSD / HDDZALMAN X3 ATX Mid Tower Computer Case fig 11

Mounting the front radiator

Caution
280mm radiator can be problematic to install on the X3. Width of the radiator should be 140mm. If you wish to use a radiator larger than 140mm please be sure to check the distance between the side of the radiator to screw hole. If the distance is below 5.7mm you can install it to X3.

RGB LED Controller

ZALMAN X3 ATX Mid Tower Computer Case fig 12

Fan Specifications

  • RFD 120A [ X3 ]
  • Dimensions : 120 x 124 x 25 mm Bearing Type : Hydraulic Bearing
  • Fan – Rating Voltage : 6~13.8 V DC
    • Rating Current : 150mA ±20%LED – Rating Voltage : 4.5~5.3 V DC
    • Rating Current : 800mA ±20%Fan Speed : 800~1,500 ±10% RPM Max Airflow : 34.34 CFM
  • Max Noise Level : 25.6 dB(A) ±10%Connector : 3-Pin, 3-Pin Addressable Weight : 160g
  • Life Span : 40,000 hrs
  • Cable Length : 580mm x 2

I/O ConnectorsZALMAN X3 ATX Mid Tower Computer Case fig 1333

www.zalman.com

Documents / Resources

ZALMAN X3 ATX Mid Tower Computer Case [pdf] User Manual
X3, ATX Mid Tower Computer Case, Mid Tower Computer Case, Tower Computer Case, X3, Computer Case, Z-Machine Gaming Gear, Gaming Gear
ZALMAN X3 ATX Mid-Tower Computer Case [pdf] User Manual
X3, ATX Mid-Tower Computer Case, Tower Computer Case, Computer Case, ATX Case, X3

References

Leave a comment

Your email address will not be published. Required fields are marked *