ZALMAN N5 MF ATX MID Tower Computer Case
Precautions
- Read this manual carefully before installing.
- Check the product and components before installing. If you find any abnormality, contact the location where you purchased the product for a replacement or refund.
- Wear gloves to prevent accidents when installing the product.
- Severe damage may occur when mounting the system, so do not apply excessive force.
- Connecting the cable incorrectly may cause a fire due to a short circuit. Make sure to refer to the manual when connecting the cable.
- Be careful not to block the ventilation hole of the product when using the system.
- Avoid locations with direct sunlight, water, moisture, oil, and excessive dust. Store and use the product in a well-ventilated location.
- Do not wipe the surface of the product using chemicals. (organic solvents such as alcohol or acetone)
- Do not insert your hand or other object into the product during operation, as this may injure your hand or damage the object.
- Store and use the product out of children’s reach.
- Our company assumes no responsibility for any problem that occurs due to theuse of the product for purposes other than its designated purposes and/or the carelessness of the consumer.
- The exterior design and specifications of the product are subject to change without prior notice to consumers for quality improvement.
Specifications
Model | N5 MF | |
Case Form Factor | ATX Mid-Tower | |
Dimensions | 437(D) x 200(W) x 450(H)mm | |
Weight | 3.6kg | |
Case Materials | Plastic, Steel | |
Motherboard Support | ATX / mATX / Mini-ITX | |
Maximum VGA Length | 365mm | |
Maximum CPU Cooler Height | 158mm | |
Maximum PSU Length | 160mm | |
PCI Expansion Slots | 7 | |
Drive Bays | 2 x Combo(3.5” or 2.5”), 4 x 2.5” SSD | |
Fan Support |
Top | 3 x 120mm |
Front | 3 x 120mm | |
Rear | 1 x 120mm | |
Bottom | 2 x 120mm | |
Fan(s) Inclued |
Front | 3 x 120mm (with RGB LED Effect) |
Rear | 1 x 120mm (with RGB LED Effect) | |
Radiator Support |
Front | 120mm / 240mm / 360mm |
Rear | 120mm | |
I/O Ports |
1 x Headphone, 1 x Mic, 2 x USB 2.0, 1 x USB 3.0, Reset Button, Power Button, Fan-LED Controller (Change Fan Speed & LED Brightness) |
Accessories
- User’s Manual
- Buzzer
- SSD / MB Screws x 20
- Cable Ties x 5
- PSU / HDD / VGA Screws x 8
- Thumm Screws x 2
- Motherboard Standoffs x 3
I/O Ports
# | Part | # | Part | # | Part | # | Part |
ⓐ | Power Button | ⓑ | USB 2.0 Ports | ⓒ | HDD / Power LED | ⓓ | Headphone Jack |
ⓔ | Microphone Jack | ⓕ | Fan Controller | ⓖ | USB 3.0 Port | ⓗ | Reset Button |
- Removing the side panels
- Acrylic Panel
- Steel Panel
- Removing the front panel
- Mounting the motherboard
- Motherboard size
Pick out the 8-Pin auxiliary power cable(CPU power connector) through the groove on top before installing motherboard.- ATX
- mATX
- Mini-ITX
- Motherboard size
- Mounting the PSU
- Mounting the PCI-E(VGA) card
- Mounting the 3.5″ and 2.5″ SSD / HDD
- Mounting the 2.5″ SSD / HDD
- Mounting the fans
- Mounting the top fans
- Mounting the bottom fans
- Fan(s) Inclued
- Front : 3 x 120mm Fan – with RGB LED Effects
- Rear : 1 x 120mm Fan – with RGB LED Effects
- Fan Controller
4 Control Modes of Fan speed & LED brightnessMode Fan Speed LED Brightness Mode 1. High High Mode 2. Low Low Mode 3. Low Off Mode 4. Off Off Caution: shutting off your system fans could cause increase of system temperature.
- I/O Connectors
Documents / Resources
![]() |
ZALMAN N5 MF ATX MID Tower Computer Case [pdf] User Manual N5 MF ATX MID Tower Computer Case, N5 MF, ATX MID Tower Computer Case |
![]() |
ZALMAN N5 MF ATX MID Tower Computer Case [pdf] User Manual N5 MF, ATX MID Tower Computer Case, N5 MF ATX MID Tower Computer Case, MID Tower Computer Case, Tower Computer Case, Computer Case, Case |
![]() |
ZALMAN N5 MF ATX Mid Tower Computer Case [pdf] User Manual N5 MF ATX Mid Tower Computer Case, N5 Computer Case, MF ATX Mid Tower Computer Case, Computer Case, ATX Mid Tower Computer Case, ATX, ATX Computer Case |