ZigBee Smart plug
Itọsọna olumulo

Ọja Ifihan

Iwọn ẹrọ naa kere ju 1 kg. Iwọn fifi sori ẹrọ ti o kere ju 2 m ni a ṣe iṣeduro.

Awọn ilana fifi sori ẹrọ

1. Agbara kuro Lati yago fun ina mọnamọna, jọwọ kan si alagbawo oniṣowo tabi alamọja ti o peye fun iranlọwọ nigba fifi sori ẹrọ ati atunṣe.
2. Ilana onirin
   Rii daju wiwọn onirin to tọ ṣaaju ṣiṣe agbara ẹrọ naa. S1/S2 can connect with the rocker light switch, or it doesn’t connect. To ensure safety, do not connect the neutral wire and live wire to it.

Awọn pato

Ọja Iru	Zigbee Smart Plug
Iṣawọle	100-240VAC 50/60Hz
Abajade	100-240VAC 50/60Hz
Max.Lẹru	10A/13A/16A/20A
ZigBee	IEEE 802.15.4 2.4GHZ
Ohun elo	PC VO

Awọn ẹya ara ẹrọ

ZigBee plug is a smart Plug that adopts the ZigBee plug wireless protocol and connects to your internet through the ZigBee hub. You can turn on/off, schedule on/off, and share the device with your family to control together, and so on.

Isakoṣo latọna jijin	Iṣeto akoko
Iṣakoso ohun	Pin Iṣakoso
Smart si nmu

The above functions are determined by the ZigBee Hub.

Ilana Ilana

1. Ṣe igbasilẹ APP naa
   Please refer to the user guide of the hub to download the corresponding APP. below platforms are recommended:

   SmartTthings	Amazon Alexa	Hue

2. Asopọmọra ibudo
   Set the hub according to the user guide. Support ZigBee plug hubs as follows:
   iwoyi Studio
   Echo Plus (awoṣe: ZE39KL)
   Ifihan Gen Echo 2nd (awoṣe: DW84JL)
   2nd Gen Echo Plus (awoṣe: L9D29R)
   Samsung SmartThings ibudo
   Philips Hue
   Ti asopọ ba kuna, jọwọ gbe ibudo naa sunmọ foonu rẹ ki o tun gbiyanju lẹẹkansi.
3. Agbara lori
   Lẹhin ti o ti tan-an, ẹrọ naa yoo tẹ ipo sisopọ pọ lakoko lilo akọkọ, ati ifihan ifihan LED seju.
    The device will exit the pairing mode if no next operation for a long time. If you enter again, please long-press the manual switch for 5s until the LED signal indicator flashes and release.
4. Sopọ si Alexa
   1. Power on the Plug
   2. Ask, “Alexa, discover devices!
   3. Plug ashes once it’s connected
   4. Wait until Alexa finishes, check the new devices” First/Second….plug”

Sopọ si SmartThings

1. Power up the smart bulb, bulb breathe 3 times, and enter the configuration state.
2. Open the SmartThings app, and click”+”, click “Device”, click “SmartThings”, click “Lighting”, click ” Smart Bulb”, click “Start”, click “Next”, click “Skip the step”, click “Done”

Atunto ile-iṣẹ

Long-press the configuration button for 5s until the LED signal indicator flashes and release, then the reset is successful. The device enters spairing mode.

If you pair the device with the hub again, please reset the device to factory default.

Ṣe lati orilẹ-ede Ṣaina

Awọn iwe aṣẹ / Awọn orisun

ZigBee Light Yipada Module [pdf] Afowoyi olumulo Light Yipada Module, Yipada Module, Module

Awọn itọkasi

• Itọsọna olumulo