I-GIII X-Prog 3 i-Immobilizer ePhezulu &
UMcwangcisi ongundoqo
Incwadi yokusebenzisa

I-GIII X-Prog 3 i-Immobilizer ephucukileyo kunye neNkqubo engundoqo

Qalisa i-GIII X-Prog ye-3 ye-Immobilizer ephucukileyo kunye neNkqubo engundoqo ye-X431 V, i-X431 V+, i-ProS, i-X431 PAD V, i-PAD VII
Uphawu: Launch-X431

Ingcaciso yeMveliso

Qalisa i-GIII X-Prog 3 sisisombululo esinamandla sokulwa nobusela kunye nokhetho olufanelekileyo kwiivenkile zokulungisa iingcali kunye namashishini okugcinwa kwezithuthi.Ifumene isitshixo sesithuthi, i-injini kunye ne-gearbox programming, equkethe ii-reprogramming multiple parts anamandla kunye noluhlu olubanzi lokugubungela isithuthi.
Qalisa i-GIII X-Prog 3 ye-Immobilizer ephucukileyo kunye neNkqubo engundoqo
Qalisa i-GIII X-PROG 3 immobilizer ephucukileyo kunye nomdwelisi ophambili sisixhobo esinamandla sokufunda itshiphu esikwaziyo ukufunda/ukubhala izitshixo zesithuthi. Iyahambelana ne-X-431 yochungechunge lwe-scanners zokuxilonga, i-X-PROG 3 yenza ukuchongwa kohlobo lwe-Anti-ubusela, ukuhambelana nokulawula okude, ukufundwa kwe-chip Key kunye nokutshatisa, ukufundwa kwephasiwedi yokulwa nobusela kunye nokutshintshwa kwecandelo lokulwa.

Qalisa i-GIII X-Prog 3 Iimpawu:

1. Iyahambelana ne-X-431 series scanners zokuxilonga, i-X-PROG 3 yenza ukuba i-EEPROM ifunde / ibhale, i-MCU ekwibhodi kunye ne-BMW CAS4 +/FEM chips, izitshixo ze-infrared ze-Mercedes-Benz, ukuvelisa izitshixo ezikhethekileyo, ukufunda ikhowudi ye-BMW ye-ISN.
2. Iimpawu ezixhaswayo: VW, AUDI, SKODA, SEAT, BMW, MERCEDES-BENZ, TOYOTA, njl. Iimodeli ezininzi ziyaqhubeka zihlaziywa.
3. Iinkqubo ezixhaswayo: Ukuhanjiswa ngokuzenzekelayo, iNkqubo yeSixhobo, i-CAS, iNkqubo yoMzimba, iNkqubo yokutshixa, njl.
4. Iyahambelana ne: X431 V, X431 V+, X431 ProS, X431 PRO GT, X431 PRO V4.0, X431 PRO 3 V4.0, X431 PRO 5, X-431 PAD III V2.0, X-431 PAD V, X- 431 PAD VII
5. Ufunda kwaye ubhale uninzi lwe-Engine/Gearbox ECUs ngaphandle kokuqhawula iqokobhe

Uhlaziyo Qaphela: Qalisa i-X431 GIII X-Prog 3 yohlaziyo lwamva nje lwe-RESET PROG (V10.05) Umsebenzi:

1. Imisebenzi eyongeziweyo ye-ECU yokufunda nokubhala kwiimodeli ezili-10 ze-Siemens Engine kuquka i-MSD80, i-MSD81, i-MSD85, i-MSD87, i-MSV90, i-SIM271DE, i-SIM271KE, i-SIMOS8.4, i-SIMOS8.5 kunye ne-SIMOS8.6;
2. Imisebenzi eyongeziweyo ye-ECU yokufunda nokubhala kwiimodeli ze-5 zoThutho olubandakanya i-9G_Tronic, i-DQ380, i-AL551, i-AL450 kunye ne-8HPXX.

Qalisa i-GIII X-Prog 3 Advantages:

1. Ixhasa VW/AUDI MQB iqonga injini ECU replacement okanye cloning (Funda idatha injini ECU ngqo ukusuka isitshixo).
2. Ixhasa VW/AUDI MQB iqonga gearbox ECU endaweni okanye cloning.
3. Ixhasa ukutshintshwa kwe-ECU kwisizukulwana sesihlanu se-Audi (0AW/0B5) gearbox.
4. Ixhasa ukufunda, ukubhala kunye nokwenza i-ECU kwisizukulwana sesine se-VW UDS injini.
5. Ixhasa BMW E chassis 8HP gearbox ECU reprogramming engenanto.
6. Isebenza kunye nesixhobo sokuhlelwa kwakhona kwi-backup / ukubuyisela idatha yeprogram (yeBosch / i-Siemens injini ye-ECU).

Qalisa i-GIII X-Prog 3 yeMisebenzi ePhambili:

1. Idityaniswe imisebenzi yokudibanisa okuphambili / ikopi, ukufunda nokubhala i-IC echasene nobusela, kunye nokufunda kwe-ECU nokubhala, njl.
2. Ixhasa abavelisi abakhulu be-ECU/MCU/EEPROM, kunye neemodeli zemveliso ezingaphezu kwe-1200, kunye nokuhlaziya rhoqo.
3. Ixhasa ukutshintshwa kwe-ECU kuzo zonke ezilahlekileyo ngaphandle kokuchithwa kwesixhobo se-VW / AUDI esingeyo-35XX (inokufundwa ngokuthe ngqo kwi-harness ezimeleyo ngaphandle kokususa i-IC).
4. Ixhasa ukutshintshwa kwe-ECU kwisizukulwana sesine se-VW/AUDI injini;
5. Ixhasa ukutshintshwa kwe-ECU kwisizukulwana sesihlanu se-VW/AUDI Bosch kunye neenjini ze-Siemens.
6. Ixhasa zonke ezilahlekileyo kunye nokutshintshwa kwesizukulwana sesine se-AUDI EZS, i-ECU ekhululekile, kunye ne-KESSY IC.
7. Ixhasa iBMW F kunye ne-G chassis 8HP gearbox ECU reprogramming engenanto.
8. Ixhasa i-BMW CAS4/CAS4+ yokutshintshwa kwemodyuli.
9. Ixhasa i-ECU cloning kunye nokutshintshwa kweenjini ze-BMW Siemens.
10. Cima igama lokugqitha le Mercedes-Benz injini kunye gearbox ngaphakathi 3S.
11. Yongeza umsebenzi wokubala igama lokugqitha isitshixo Mercedes-Benz ngaphakathi 1 umzuzu.

Qalisa i-GIII X-Prog 3 yeempawu zeChip ezixhaswayo:
Ixhasa abavelisi be-ECU abaqhelekileyo be-MCU, kunye neemodeli zemveliso ezingaphezu kwe-1,000, kwaye zihlala zihlaziywa.

Iimpawu ze-EEPROM ezixhaswayo:
Ixhasa abavelisi be-EEPROM abaqhelekileyo abaqhelekileyo, kunye neemodeli zemveliso eziphantse zibe yi-1,000, kwaye zihlaziywa ngokuqhubekayo.

Qalisa uQhagamshelwano lokuSebenza lwe-X-PROG3:
Indlela yokudibanisa i-1: Qhagamshela ngokuthe ngqo kwi-OBD16 yokudibanisa okubalulekileyo, ukufundwa kwedatha kunye nokubhala, njl

Indlela yokudibanisa 2: Beka i-EEPROM echasene nobusela okanye i-MCU ye-chip kwi-socket evuthayo ye-chip, uze ufake i-socket evuthayo kwi-slot ye-immobilizer programmer locker kwaye uyitshixe ukuqonda ukusebenzisana kwedatha phakathi kwe-IC anti-ubusela chip kunye umamkeli woxilongo

Indlela yokudibanisa i-3: Emva kokususa i-ECU kwimoto, qhagamshela i-ECU ye-anti-theft pin kwi-DIY slot ye-immobilizer programmer ngekhebula ukuqonda ukusebenzisana kwedatha phakathi kwe-ECU yokulwa nobusela kunye ne-diagnostic host.

Yazisa iX-PROG 3 yeSikhokelo soHlaziyo:

1. Kwisikrini esiphambili sokuxilonga, cofa uHlaziyo lweSoftware ukungena kwiziko lohlaziyo. Jonga isoftwe ofuna ukuyiphucula, uze ucofe Hlaziya.
2. Nje ukuba ukukhuphela kugqityiwe, iipakethe zesoftware ziya kufakwa ngokuzenzekelayo.

Yazisa umboniso we-X-PROG3:

1. I-DB26 yokuxilonga isidibaniso: Ukudibanisa nazo zonke iintambo ezichasene nobusela.
2. Benz isitshixo slot: Ukubeka Benz isitshixo semoto.
3. I-slot engundoqo: Ukubeka isitshixo semoto kwi-RF defection.
4. Key chip slot: Ukubeka isitshixo chip.
5. Isalathisi samandla
   • Isibane esibomvu sibonisa iimpazamo.
   • Isibane esiorenji sibonisa imisebenzi eqhelekileyo.
6. Ivalve: Ukuqinisa ibhodi ye-EEPROM ekhululekile.
7. EEPROM slot: Ukufaka EEPROM ibhodi
8. Isibuko samandla: Ukutshaja amandla
9. I-DB15 isidibaniso sokuxilonga: Ukudibanisa nentambo yokuxilonga engundoqo.
10. I-DIY slot: Ukufaka ibhodi ye-DIY yesithuthi.

Qalisa iX-Prog 3 FAQ:

Yazisa iX-Prog 3 iNgcaciso:

Ujongano	DB26, DB15
Igalelo lamandla	DC12V
Ukusebenza CurrentMax	500mA
Ukutya umbane	5W
Ubushushu boGcino	-20℃~70℃
Ubushushu bokusebenza	0℃~50℃
Ubungakanani	228*120 mm

Yazisa i-XPROG-3 yoLuhlu lweePakethi:

• Iyunithi ephambili
• Iadaptha yamandla
• Intambo yoxilongo oluphambili
• Isizukulwana sesine sokufumana intambo yedatha
• Isizukulwana sesine se-EEPROM data acquisition cable(ngaphandle kokudiliza ideshibhodi)
• I-BENCH intambo yemowudi
• Umguquleli we-MCU V1
• Umguquleli we-MCU V2
• Intambo ye-MCU enezikhokelo ezininzi
• I-adaptha yetshiphu ye-EEPROM
• Iqhosha lokufumana i-analog ye-Benz ye-infrared
• Intambo ye-MCU enezikhokelo ezininzi
• EEPROM isiguquli
• Incwadi yokusebenzisa

Amaxwebhu / Izibonelelo

YENZA i-GIII X-Prog 3 ye-Immobilizer ephucukileyo kunye neNkqubo engundoqo [pdf] Incwadi yokusebenzisa I-GIII X-Prog 3, i-Advanced Immobilizer Key Programmer, i-Immobilizer Key Programmer, i-Advanced Key Programmer, uMcwangcisi oPhambili, uMcwangcisi

Iimbekiselo

• Incwadi yokusebenzisa