GIII X-Prog 3 Advanced Immobilizer &
Igodo Mmemme
Akwụkwọ ntuziaka onye ọrụ

GIII X-Prog 3 Advanced Immobilizer & Key Programmer

Ẹkedori GIII X-Prog 3 Advanced Immobilizer & Key Programmer maka X431 V, X431 V+, ProS, X431 PAD V, PAD VII
Ụdị: Mwepụta-X431

Nkọwa ngwaahịa

Mwepụta GIII X-Prog 3 bụ ihe ngwọta dị ike na-egbochi izu ohi yana nhọrọ dị mma maka ụlọ ahịa ndozi ọkachamara na azụmaahịa na-arụzi ụgbọ ala.Ọ nwetala igodo ụgbọ ala, mmemme injin na igbe gearbox, na-egosipụta mmegharị akụkụ dị ike na nhazigharị ụgbọ ala yana ọtụtụ mkpuchi ụgbọ ala.
Ẹkedori GIII X-Prog 3 Advanced Immobilizer & Key Programmer
Mwepụta GIII X-PROG 3 Advanced immobilizer & Key programmer bụ ngwaọrụ ọgụgụ mgbawa siri ike nke nwere ike ịgụ/de igodo ụgbọ ala ahụ. Dakọtara na X-431 usoro nyocha nyocha nyocha, X-PROG 3 na-enyere ụdị njirimara mgbochi izu ohi, njikwa njikwa anya, ọgụgụ isi mgbawa & dakọtara, ọgụgụ okwuntughe mgbochi izu ohi na nnọchi akụkụ mgbochi izu ohi.

Mwepụta GIII X-Prog 3 atụmatụ:

1. Dakọtara na X-431 usoro nyocha nyocha, X-PROG 3 na-enyere aka ịgụ / ide EEPROM, on-board MCU na BMW CAS4 +/FEM ibe, Mercedes-Benz infrared igodo, na-amụba igodo pụrụ iche, ịgụ BMW engine ISN code.
2. Ụdị akwadoro: VW, AUDI, SKODA, SEAT, BMW, MERCEDES-BENZ, TOYOTA, wdg. A na-emelite ụdị ndị ọzọ.
3. Usoro akwadoro: Mbufe akpaaka, Sistemụ Ngwa, CAS, Sistemụ Ahụ, Sistemu Mkpọchi, wdg.
4. Dakọtara na: X431 V, X431 V+, X431 ProS, X431 PRO GT, X431 PRO V4.0, X431 PRO 3 V4.0, X431 PRO 5, X-431 PAD III V2.0, X-431 PAD V, X-431 PAD VII
5. Na-agụ ma na-ede ọtụtụ Engine/Gearbox ECUs na-agbasaghị shei ahụ

Mara Nwelite: Mwepụta X431 GIII X-Prog 3 mmelite kachasị ọhụrụ maka ọrụ RESET PROG (V10.05):

1. Agbakwunyere ECU ịgụ na ide ọrụ maka ụdị 10 nke Siemens Engine gụnyere MSD80, MSD81, MSD85, MSD87, MSV90, SIM271DE, SIM271KE, SIMOS8.4, SIMOS8.5 na SIMOS8.6;
2. Agbakwunyere ECU ọgụgụ na ide ọrụ maka ụdị 5 nke nnyefe gụnyere 9G_Tronic, DQ380, AL551, AL450 na 8HPXX.

Mwepụta GIII X-Prog 3 Advantages:

1. Na-akwado VW/AUDI MQB n'elu ikpo okwu engine ECU nnọchi ma ọ bụ cloning (Gụọ engine ECU data ozugbo site na igodo).
2. Na-akwado VW/AUDI MQB ikpo okwu gearbox ECU nnọchi ma ọ bụ cloning.
3. Na-akwado nnọchi ECU maka ọgbọ nke ise nke Audi (0AW/0B5) gearbox.
4. Na-akwado ịgụ, ide & imechi ECU maka ọgbọ nke anọ nke VW UDS engine.
5. Na-akwado BMW E chassis 8HP gearbox ECU na-emegharị ka ọ tọgbọ chakoo.
6. Na-arụ ọrụ na ngwaọrụ reprogramming ka ndabere / weghachi data mmemme (Maka Bosch/Siemens engine ECU).

Mwepụta GIII X-Prog 3 Isi Ọrụ:

1. Ejikọtara ọrụ nke isi ndakọrịta/mbipụta, mgbochi izu ohi IC ịgụ & ide ihe, yana ịgụ na ide ECU, wdg.
2. Na-akwado ndị nrụpụta ECU/MCU/EEPROM nkịtị, nwere ụdị ngwaahịa karịrị 1200, na-emelite mgbe niile.
3. Na-akwado nnọchi ECU maka ndị niile furu efu na-enweghị disssembly maka ngwa VW/AUDI na-abụghị 35XX (enwere ike ịgụ ya ozugbo site na njide onwe ya na-ewepụghị IC).
4. Na-akwado nnọchi ECU maka ọgbọ nke anọ nke VW/AUDI engine;
5. Na-akwado nnọchi ECU maka ọgbọ nke ise nke VW/AUDI Bosch na Siemens engines.
6. Na-akwado ndị niile furu efu na nnọchi maka ọgbọ nke anọ nke AUDI EZS, ECU dị mma na KESSY IC.
7. Na-akwado BMW F na G chassis 8HP gearbox ECU ịmegharị ka ọ tọgbọ chakoo.
8. Na-akwado nnọchi BMW CAS4/CAS4+ modul.
9. Na-akwado cloning ECU na nnọchi maka injin BMW Siemens.
10. Hichapụ paswọọdụ maka Mercedes-Benz engine na gearbox n'ime 3S.
11. Tinye ọrụ nke ịgbakọ paswọọdụ maka igodo Mercedes-Benz n'ime nkeji 1.

Mwepụta GIII X-Prog 3 Ụdị Chip akwadoro:
Ọ na-akwado ndị na-emepụta ECU MCU nkịtị, yana ụdị ngwaahịa karịrị 1,000, a na-emelitekwa ha mgbe niile.

Ụdị EEPROM akwadoro:
Ọ na-akwado ndị na-emepụta EEPROM ndị nkịtị, yana ihe fọrọ nke nta ka ọ bụrụ 1,000 ụdị ngwaahịa, a na-emelitekwa ha mgbe niile.

Mwepụta njikọ ọrụ X-PROG3:
Usoro njikọ 1: Jikọọ ozugbo na OBD16 maka ndakọrịta igodo, ọgụgụ data na ide ihe, wdg

Usoro njikọ 2: Tinye mgbochi EEPROM ma ọ bụ MCU mgbawa n'ime oghere na-ere ọkụ, wee tinye oghere na-ere ọkụ n'ime oghere nke mkpuchi ihe mmemme immobilizer wee kpochie ya iji ghọta mmekọrịta data dị n'etiti mgbawa mgbochi ohi IC na onye nlekọta nyocha.

Usoro njikọ 3: Mgbe iwepu ECU na ụgbọ ala, jikọọ mgbochi-ezu ohi ECU pin ka oghere Mee N'onwe Gị nke immobilizer programmer site na USB ịghọta data mmekọrịta n'etiti mgbochi-ezu ohi ECU na diagnostic usu.

Mwepụta ntuziaka mmelite X-PROG 3:

1. Na isi nchoputa ihuenyo, kpatụ Software Nwelite ka ịbanye n'etiti mmelite. Lelee ngwanrọ ịchọrọ ịkwalite, wee pịa Mmelite.
2. Ozugbo nbudata nbudata, a ga-etinye ngwungwu ngwanrọ na-akpaghị aka.

Mwepụta ihe ngosi X-PROG3:

1. Njikọ nchọpụta nchọpụta DB26: Iji jikọọ na eriri mgbochi izu ohi niile.
2. Oghere igodo Benz: Ka idowe igodo ụgbọ ala Benz.
3. Oghere igodo: Dowe igodo ụgbọ ala maka nrụrụ RF.
4. Oghere mgbawa igodo: Ka idowe mgbawa igodo.
5. Ngosipụta ike
   • Ìhè na-acha uhie uhie na-egosi mmejọ.
   • Ìhè oroma na-egosi ọrụ ọ bụla.
6. Valve: Iji mesie bọọdụ EEPROM rụrụ arụ.
7. Oghere EEPROM: Iji tinye bọọdụ EEPROM
8. Ọdụ ụgbọ mmiri: Maka ịchaji ike
9. Njikọ nchọpụta nchọpụta DB15: Iji jikọọ na eriri nchọpụta isi.
10. Oghere N'onwe Gị: Iji tinye bọọdụ DIY ụgbọ ala.

Mwepụta X-Prog 3 FAQ:

Mwepụta nkọwapụta X-Prog 3:

Interface	DB26, DB15
Ike ntinye	DC12V
Na-arụ ọrụ CurrentMax	500mA
Oriri ike	5W
Okpomọkụ nchekwa	-20 ℃ ~ 70 ℃
Okpomọkụ na-arụ ọrụ	0 ℃ ~ 50 ℃
Nha	228 * 120 mm

Mwepụta Ndepụta ngwugwu XPROG-3:

• Isi nkeji
• Ihe nkwụnye ọkụ
• Igwe nyocha isi
• Ọgbọ nke anọ data enweta USB
• Ọgbọ nke anọ nke eriri nnweta data EEPROM (na-ewepụghị dashboard)
• USB mode bench
• MCU ntụgharị V1
• MCU ntụgharị V2
• USB MCU nwere ọtụtụ ụzọ
• Ihe nkwụnye ọkụ EEPROM
• Igodo nnweta analọgụ Benz infrared
• USB MCU nwere ọtụtụ ụzọ
• Ihe ntụgharị EEPROM
• Akwụkwọ ntuziaka onye ọrụ

Akwụkwọ / akụrụngwa

Mwepụta GIII X-Prog 3 Advanced Immobilizer & Key Programmer [pdf] Akwụkwọ ntuziaka onye ọrụ GIII X-Prog 3, Advanced Immobilizer Key Programmer, Immobilizer Key Programmer, Advanced Key Programmer, Key Programmer, Programmer

Ntụaka

• Akwụkwọ ntuziaka onye ọrụ