GIII X-Prog 3 Immobilizer e tsoetseng pele leamp;
Lenaneo la Key
Bukana ea Mosebelisi

GIII X-Prog 3 Advanced Immobilizer & Key Programmer

Qala GIII X-Prog 3 Advanced Immobilizer & Key Programmer bakeng sa X431 V, X431 V+, ProS, X431 PAD V, PAD VII
Lebitso: Launch-X431

Tlhaloso ea Sehlahisoa

Launch GIII X-Prog 3 ke tharollo e matla e khahlanong le bosholu le khetho e nepahetseng bakeng sa mabenkele a litsebi tsa ho lokisa le likhoebo tsa tlhokomelo ea likoloi.E fihletse senotlolo sa koloi, lenaneo la Enjine le lebokose la li-gearbox, le nang le likarolo tse ngata tse matla tsa ho tsosolosa likarolo le mefuta e mengata ea likoloi.
Qala GIII X-Prog 3 Advanced Immobilizer & Key Programmer
Launch GIII X-PROG 3 advanced immobilizer & key programmer ke sesebelisoa se matla sa ho bala chip se khonang ho bala / ho ngola linotlolo tsa koloi. E lumellana le li-scanner tsa tlhahlobo ea X-431, X-PROG 3 e thusa ho tsebahatsa mofuta o khahlanong le bosholu, ho tsamaisana le taolo ea Remote, Key chip Read & matching, ho bala li-password tse khahlanong le bosholu le karolo e khahlanong le bosholu.

Qala GIII X-Prog 3 Likarolo:

1. E lumellana le li-scanner tsa X-431 letoto la tlhahlobo, X-PROG 3 e nolofalletsa ho bala / ho ngola EEPROM, li-chips tsa MCU le BMW CAS4 +/FEM, linotlolo tsa infrared tsa Mercedes-Benz, ho hlahisa linotlolo tse khethehileng, ho bala khoutu ea ISN ea BMW.
2. Mefuta e tšehelitsoeng: VW, AUDI, SKODA, SEAT, BMW, MERCEDES-BENZ, TOYOTA, joalo-joalo Mehlala e meng e ntse e ntlafatsoa.
3. Sistimi e ts'ehelitsoeng: Phetiso ea Motlakase, Sisteme ea Lisebelisoa, CAS, Sistimi ea 'mele, Sistimi ea Lock, joalo-joalo.
4. E lumellana le: X431 V, X431 V+, X431 ProS, X431 PRO GT, X431 PRO V4.0, X431 PRO 3 V4.0, X431 PRO 5, X-431 PAD III V2.0, X-431 PAD V, X- 431 PAD VII
5. E bala le ho ngola boholo ba Engine/Gearbox ECUs ntle le ho qhaqholla khetla

Tlhokomeliso ea Nchafatso: Qala ntlafatso ea morao-rao ea X431 GIII X-Prog 3 bakeng sa Mosebetsi oa RESET PROG (V10.05):

1. Mesebetsi e ekelitsoeng ea ECU ea ho bala le ho ngola bakeng sa mefuta e 10 ea Siemens Engine ho kenyeletsa MSD80, MSD81, MSD85, MSD87, MSV90, SIM271DE, SIM271KE, SIMOS8.4, SIMOS8.5 le SIMOS8.6;
2. E kentse mesebetsi ea ho bala le ho ngola ECU bakeng sa mefuta e 5 ea Transmission ho kenyelletsa 9G_Tronic, DQ380, AL551, AL450 le 8HPXX.

Qala GIII X-Prog 3 Advantages:

1. E tšehetsa VW/AUDI MQB platform engine ECU replace kapa cloning (Bala data ya enjene ECU ka kotloloho ho tswa ho senotlolo).
2. E tšehetsa VW/AUDI MQB sethaleng gearbox ECU sebaka kapa cloning.
3. E tšehetsa phetoho ea ECU bakeng sa lebokose la gear la Audi (0AW/0B5) la moloko oa bohlano.
4. E ts'ehetsa ho bala, ho ngola le ho kopanya ECU bakeng sa moloko oa bone oa enjene ea VW UDS.
5. E tšehetsa BMW E chassis 8HP gearbox ECU reprogramming ho se na letho.
6. E sebetsa ka sesebelisoa sa ho hlophisa bocha ho boloka / ho khutlisetsa data ea lenaneo (Bakeng sa Bosch/Siemens engine ECU).

Qala GIII X-Prog 3 Mesebetsi ea Bohlokoa:

1. E kopantse mesebetsi ea bohlokoa ea ho bapisa / kopi, ho bala le ho ngola ha IC e khahlano le bosholu, le ho bala le ho ngola ECU, jj.
2. E ts'ehetsa bahlahisi ba ka sehloohong ba ECU/MCU/EEPROM, ba nang le mefuta e fetang 1200 ea lihlahisoa, 'me e lula e nchafatsoa.
3. E tšehetsa phetoho ea ECU bakeng sa bohle ba lahlehileng ntle le ho qhaqhoa bakeng sa sesebelisoa sa VW/AUDI seo e seng 35XX (e ka baloa ka ho toba ka har'a marapo a ikemetseng ntle le ho tlosa IC).
4. E tšehetsa phetoho ea ECU bakeng sa moloko oa bone oa enjene ea VW/AUDI;
5. E tšehetsa phetoho ea ECU bakeng sa moloko oa bohlano oa lienjiniere tsa VW/AUDI Bosch le Siemens.
6. E ts'ehetsa tsohle tse lahlehileng le tse nchafalitsoeng bakeng sa moloko oa bone oa AUDI EZS, ECU e phutholohileng, le KESSY IC.
7. E ts'ehetsa BMW F le G chassis 8HP gearbox ECU reprogramming ho se be letho.
8. E ts'ehetsa phetoho ea mojule oa BMW CAS4/CAS4+.
9. E ts'ehetsa ho kopanngoa ha ECU le ho nkela lienjine tsa BMW Siemens sebaka.
10. Hlakola phasewete bakeng sa enjene ea Mercedes-Benz le lebokose la gear ka har'a 3S.
11. Eketsa mosebetsi oa ho bala phasewete bakeng sa senotlolo sa Mercedes-Benz nakong ea motsotso o le mong.

Qala GIII X-Prog 3 Li-Brand tsa Chip tse Tšehetsoeng:
E ts'ehetsa bahlahisi ba tloaelehileng ba ECU MCU, ba nang le mefuta e fetang 1,000 ea lihlahisoa, 'me ba ntse ba ntlafatsoa khafetsa.

Lihlahisoa tsa EEPROM tse tšehelitsoeng:
E ts'ehetsa bahlahisi ba tloaelehileng ba EEPROM, ba nang le mefuta e ka bang 1,000 ea lihlahisoa, 'me e ntse e ntlafatsoa khafetsa.

Qala Khokahano ea Ts'ebetso ea X-PROG3:
Mokhoa oa khokahano 1: Hokela ka kotloloho ho OBD16 bakeng sa ho bapisa lintlha, ho bala le ho ngola data, jj

Mokhoa oa 2 oa ho hokahanya: Beha chip ea EEPROM kapa ea MCU e thibelang bosholu ka har'a sokete e tukang, ebe o kenya sokete e tukang ka har'a slot ea mochini oa mochini oa immobilizer ebe o e notlela ho hlokomela tšebelisano ea data lipakeng tsa IC anti-theft chip le moamoheli oa tlhahlobo ea mafu

Mokhoa oa ho hokahanya 3: Ka mor'a ho tlosa ECU koloing, kopanya pini ea ECU e khahlanong le bosholu ho DIY slot ea mochine oa immobilizer ka mohala ho hlokomela tšebelisano ea data pakeng tsa ECU e khahlanong le bosholu le moeti oa ho hlahloba.

Qala Tataiso ea ntlafatso ea X-PROG 3:

1. Ho skrine se seholo sa tlhahlobo, tlanya Software Update ho kenya setsi sa ntlafatso. Sheba software eo u batlang ho e ntlafatsa, ebe u tlanya Update.
2. Hang ha download e felile, liphutheloana tsa software li tla kenngoa ka bo eona.

Hlahisa Pontšo ea X-PROG3:

1. Sehokelo sa tlhahlobo ea DB26: Ho hokahana le likhoele tsohle tse khahlanong le bosholu.
2. Benz key slot: Ho beha senotlolo sa koloi sa Benz.
3. Senotlolo sa senotlolo: Ho beha senotlolo sa koloi bakeng sa RF defection.
4. Key chip slot: Ho beha chip ea senotlolo.
5. Letšoao la matla
   • Leseli le khubelu le bontša liphoso.
   • Leseli la lamunu le bontša mesebetsi e tloaelehileng.
6. Valofo: Ho tiisa boto ea EEPROM e hlephileng.
7. EEPROM slot: Ho kenya boto ea EEPROM
8. Power port: Bakeng sa ho tjhaja matla
9. DB15 sehokelo sa tlhahlobo: Ho hokela le thapo e kholo ea tlhahlobo.
10. DIY slot: Ho kenya koloi ea DIY board.

Qala X-Prog 3 FAQ:

Hlalosa Litlhaloso tsa X-Prog 3:

Sehokedi	DB26, DB15
Matla a Kena	DC12V
Ho sebetsa CurrentMax	500mA
Tšebeliso ea Matla	5W
Mocheso oa polokelo	-20 ℃ ~ 70 ℃
Mocheso oa Mosebetsi	0℃~50℃
Boholo	228 * 120 limilimithara

Qala Lenane la Liphutheloana tsa XPROG -3:

• Sehlopha se seholo
• Adapter ea matla
• Kabel e ka sehloohong ea tlhahlobo
• Moloko oa bone oa thapo ea ho fumana data
• Moloko oa bone oa thapo ea ho fumana data ea EEPROM (ntle le ho qhaqha dashboard)
• BENCH mode cable
• MCU converter V1
• MCU converter V2
• Cable ea MCU e nang le lisebelisoa tse ngata
• EEPROM chip adaptara
• Senotlolo sa ho fumana analoge ea Benz ea infrared
• Cable ea MCU e nang le lisebelisoa tse ngata
• EEPROM converter
• Bukana ea Mosebelisi

Litokomane / Lisebelisoa

QALA GIII X-Prog 3 e tsoetseng pele ea Immobilizer & Key Programmer [pdf] Bukana ea Mosebelisi GIII X-Prog 3, Advanced Immobilizer Key Programmer, Immobilizer Key Programmer, Advanced Key Programmer, Key Programmer, Programmer

Litšupiso

• Bukana ea Mosebelisi