Umboniso unokulawulwa ngeendlela ezi-4 ezahlukeneyo: I2C, SPI,
I-8-bit parallel 6800 interface, kunye ne-8-bit parallel 8080 interface.
Ngokungagqibekanga, umboniso ulungiselelwe ulawulo lweSPI. Ukutshintshela kwi
enye indlela yokulawula, kufuneka uphinde uthengise i-resistators BS1 kunye
BS2 ngasemva ebhodini.

Imiyalelo yokusetyenziswa kwemveliso

Ukuqhagamshela iModyuli yokuBonisa

1. Xhuma i-VSS (Pin 1) kumhlaba wangaphandle.

Ukunika amandla uMboniso

1. Xhuma i-VDD (i-Pin 2) kunikezelo lwamandla lwe-3.3-5V yokubonisa
  isekethe yemodyuli.

FAQ

Ndiyitshintsha njani indlela yolawulo yomboniso?

Ukutshintsha indlela yokulawula yesiboniso, kufuneka wenze njalo
re-solder the resistors BS1 kunye BS2 ngasemva ebhodini esekelwe
kujongano olufunwayo (I2C, SPI, 8-bit parallel 6800, okanye 8-bit
ngokuhambelana 8080).

View Fullscreen

I-OLED-BONISA IMODULI
I-COM-OLED2.42
1. IINKCUKACHA NGOKUBANZI mthengi othandekayo, enkosi kakhulu ngokukhetha imveliso yethu. Koku kulandelayo, siza kukwazisa ngento omawuyiqwalasele ngelixa uqalisa kwaye usebenzisa le mveliso. Ukuba ufumana naziphi na iingxaki ezingalindelekanga ngexesha lokusetyenziswa, nceda wenze
www.joy-it.net Pascalstr. 8 47506 Neukirchen-Vluyn

2. I-PIN ISABELO SEMBONISO

Iphini lokuchongwa inombolo yePin I/O

Umsebenzi

VSS

P Logic umhlaba wesekethe

Le yiphini lomhlaba. Ikwasebenza njengesalathiso sezikhonkwane zelogic. Kufuneka idibaniswe nomhlaba wangaphandle.

VDD

I-3,3 - 5V Ubonelelo lwaMandla kwisekethe yemodyuli yokubonisa

Eli liphini lonikezelo lwamandla.

– Voltage unikezelo lwe OEL panel

Lo ngowona mqulu unika ithembatage iphini lonikezelo lwetshiphu.

Nceda ungayidibanisi.

I Data/Command Control

Le pin yidatha / iphini yokulawula umyalelo. Xa isikhonkwane sitsalwa phezulu, igalelo kwi-D7 ~ D0 liphathwa njengedatha yokubonisa. Xa isikhonkwane sitsalwa phantsi, igalelo kwi-D7~D0 lidluliselwa kwirejista yomyalelo.

/WR

Ndiyafunda/Ndibhala Khetha okanye Ndibhale

Eli phini ligalelo lojongano lwe-MCU. Xa uqhagamshelwe kwi-microprocessor yechungechunge lwe-68XX, le pin isetyenziswa njengenqaku lokufunda / ukubhala (R / W). Tsala le phini iphakamileyo kwimowudi yokufunda kwaye uyitsale ezantsi kwimowudi yokubhala. Xa imowudi yojongano lwe-80XX ikhethiwe, le pin igalelo lokubhala (WR). Umsebenzi wokubhala idatha uqaliswa xa le pin itsalwa "Phantsi" kwaye i-CS itsalwa "Phantsi".

/RD

Ndiyafunda/Ndibhala Vulela okanye Ndiyafunda

Eli phini ligalelo lojongano lwe-MCU. Xa uqhagamshelwe kwi-microprocessor yechungechunge lwe-68XX, le pin isetyenziswa njenge-Enable (E) isignali. Umsebenzi wokufunda/ubhala uqaliswa xa isikhonkwane sitsalwa phezulu kwaye iCS itsalwa phantsi. Xa uqhagamshelwe kwi-microprocessor ye-80XX, le pin ifumana uphawu lwe-Read (RD). Umsebenzi wokufundwa kwedatha uqaliswa xa le pin itsalwa phantsi kwaye i-CS itsalwa phantsi.

www.joy-it.net Pascalstr. 8 47506 Neukirchen-Vluyn

Iphini lokuchongwa inombolo yePin I/O

Umsebenzi

DB0

I/O

DB1

I/O

DB2

I/O Inginginya idatha yedatha / ibhasi yemveliso

DB3

I/O

Ezi zikhonkwane ziyi-bidirectional 8-bit data bus ezidibanisa kwi-microprocessor data

DB4

I/O ibhasi. Xa imo yothotho ikhethiwe, i-D1 yi

DB5

I/O

Igalelo ledatha ye-SDIN ye-serial kunye ne-D0 yi-SCLK ye-serial clock input.

DB6

I/O

DB7

I/O

/CS

I Chip-Khetha

Eli phini ligalelo lokukhetha itshiphu. Itshiphu yenziwe kuphela kunxibelelwano lwe-MCU xa i-CS# itsalwa phantsi.

/SETHA KWAKHONA i-NC (BS1) NC (BS2)
NC FG

I Ukusetha kwakhona Amandla kuMlawuli kunye noMqhubi

Eli phini ligalelo lokusetha kwakhona uphawu. Xa ipini iphantsi, ukuqaliswa kwe-chip kuyenziwa.

H/L Ukukhetha iprotocol yonxibelelwano

H/L

Ezi zikhonkwane ngamagalelo okukhetha ujongano lwe-MCU.

Bona le theyibhile ilandelayo:

p6a8raXlXle- l

BS1

BS2

80XX ngokunxuseneyo
1 1

I2C Uthotho
1 0 0 0

-NC okanye uqhagamshelo kwiVSS.

0V Kufuneka idityaniswe kumhlaba wangaphandle.

www.joy-it.net Pascalstr. 8 47506 Neukirchen-Vluyn

2. 1 UKUSETYENZISWA KWE-DISPLAY INTERFACE

Umboniso unokulawulwa kwiindlela ezi-4 ezahlukeneyo, nge-I2C, i-SPI, i-8-bit parallel 6800 interface kunye ne-8-bit parallel 8080 interface. Umboniso uhanjiswa uqwalaselwe kwangaphambili kulawulo nge-SPI. Ukuba ufuna ukusebenzisa enye yezinye iindlela zolawulo, kufuneka uphinde uthengise i-resistators BS1 kunye ne-BS2 ngasemva kwebhodi.

Kwitheyibhile, unokubona ukuba izichasi kufuneka zibekwe njani kwimowudi efanelekileyo.

6800-parallel 8080-parallel

I2C

SPI

BS1

BS2

3. SEBENZISA NGE-ARDUINO Njengoko umboniso usebenza nge-3V logic level kunye ne-Arduinos eninzi ene-5V, sisebenzisa i-Arduino Pro Mini 3.3V kule ex.ample. Ukuba ufuna ukusebenzisa i-Arduino kunye nenqanaba le-logic ye-5V, njenge-Arduino Uno, kufuneka unciphise yonke imigca yedatha esuka kwi-Arduino ukuya kwisiboniso ukusuka kwi-5V ukuya kwi-3.3V nge-converter yezinga le-logic.

Okokuqala kufuneka ufake ilayibrari efunekayo kwiArduino IDE yakho.

Ukwenza oku, ithala leencwadi

yiya ku U8g2

bTyooollsiv-e>rLawula

Amathala eencwadi...

ukufuna

ngenxa

u8g2

kwaye

faka

www.joy-it.net Pascalstr. 8 47506 Neukirchen-Vluyn

SPI-Interface
Iintambo

Bonisa iPin 1 2 4 7 8 15 16

Arduino Pro Mini Pin

GND

3,3V (VCC)

www.joy-it.net Pascalstr. 8 47506 Neukirchen-Vluyn

SPI-Interface
Ngoku vula ikhowudi ye-GraphicTest sample yethala leencwadi. Ukwenza oku, cofa ku: File -> Eksamples -> U8g2 -> u8x8-> GraphicTest Ngoku faka lo makhi ulandelayo wokuboniswa kwinkqubo, njengoko kubonisiwe kumfanekiso ongezantsi: U8X8_SSD1309_128X64_NONAME2_4W_SW_SPI u8x8(13, 11, 10, 9, 8);
Ngoku ungalayisha i-example kwiArduino yakho.
www.joy-it.net Pascalstr. 8 47506 Neukirchen-Vluyn

I2C-Interface
Iintambo

Bonisa iPin 1 2 4 7 8 9 16

Arduino Pro Mini Pin

GND

3,3V (VCC)

GND

www.joy-it.net Pascalstr. 8 47506 Neukirchen-Vluyn

I2C-Interface
Ngoku vula ikhowudi ye-GraphicTest sample yethala leencwadi. Ukwenza oku, cofa ku: File -> Eksamples -> U8g2 -> u8x8-> GraphicTest Ngoku faka lo makhi ulandelayo womboniso kwinkqubo, njengoko kubonisiwe kumfanekiso ongezantsi: U8X8_SSD1309_128X64_NONAME2_HW_I2C u8x8(9, A4, A5);
Ngoku ungalayisha i-example kwiArduino yakho.
www.joy-it.net Pascalstr. 8 47506 Neukirchen-Vluyn

8 bit Parallel 6800-Interface
Iintambo

Bonisa iPin 1 2 4 5 6 7 8 9 10 11 12 13 14 15 16

Arduino Pro Mini Pin

GND

3,3V (VCC)

GND

13 11 2

6 A3 10 8

www.joy-it.net Pascalstr. 8 47506 Neukirchen-Vluyn

8 bit Parallel 6800-Interface
Ngoku vula ikhowudi ye-GraphicTest sample yethala leencwadi. Ukwenza oku, cofa ku: File -> Eksamples -> U8g2 -> u8x8-> GraphicTest Ngoku faka umakhi ulandelayo womboniso kwinkqubo, njengoko kubonisiwe kumfanekiso ongezantsi: U8X8_SSD1309_128X64_NONAME0_6800 u8x8(13, 11, 2, 3, 4, 5, 6, 3, 7, 10);
Ngoku ungalayisha i-example kwiArduino yakho.
www.joy-it.net Pascalstr. 8 47506 Neukirchen-Vluyn

8 bit Parallel 8080-Interface
Iintambo

Bonisa iPin 1 2 4

Arduino Pro Mini Pin

GND

3,3V (VCC)

5 6 7 8 9 10 11 12 13 14 15 16

3,3V (VCC)

6 A3 10 8

www.joy-it.net Pascalstr. 8 47506 Neukirchen-Vluyn

8 bit Parallel 8080-Interface
Ngoku vula ikhowudi ye-GraphicTest sample yethala leencwadi. Ukwenza oku, cofa ku: File -> Eksamples -> U8g2 -> u8x8-> GraphicTest Ngoku faka lo makhi ulandelayo womboniso kwinkqubo, U8X8_SSD1309_128X64_NONAME0_8080 u8x8(13, 11, 2, 3, 4, 5, 6, A3, 7, 10_9X8_NONAMEXNUMX_XNUMX uXNUMXxXNUMX(XNUMX, XNUMX, XNUMX, XNUMX, XNUMX, XNUMX, XNUMX, AXNUMX, XNUMX, XNUMX);
Ngoku ungalayisha i-example kwiArduino yakho.
www.joy-it.net Pascalstr. 8 47506 Neukirchen-Vluyn

4. SEBENZISA NERASPBERRY PI

Le miyalelo yabhalwa phantsi kweRaspberry Pi OS

I-Bookworm ye-Raspberry Pi 4 kunye ne-5. Akukho zitsheki eziye zenziwa

yenziwe ngezinye/ezintsha iinkqubo zokusebenza okanye ihardware.

Ukwenza ukusebenzisa umboniso ngeRaspberry Pi kube lula ngakumbi, sisebenzisa ilayibrari yeluma.oled. Ungafakela uxhomekeko olufunekayo kufakelo ngale miyalelo ilandelayo:
sudo apt ukufaka igit python3-dev python3-pip python3-numpy libfreetype6-dev libjpeg-dev yakha-ibalulekile sudo apt ukufaka libsdl2-dev libsdl2-image-dev libsdl2-mixerdev libsdl2 imfuneko-ujongano lwe-ttv-dev ngenisa lo myalelo ulandelayo:
sudo raspi-config Ngoku ungenza iSPI kunye ne-I2C zisebenze phantsi kweeNdlela eziNgcono ezi-3 ukuze ukwazi ukusebenzisa zombini ujongano. Kuya kufuneka ngoku udale imeko-bume yenyani yale projekthi. Ukwenza oku, ngenisa le miyalelo ilandelayo:
mkdir your_project cd your_project python -m venv –system-site-packages env source env/bin/activate Ngoku faka ilayibrari yeluma ngalo myalelo: pip3 install –upgrade luma.oled Khuphela i sample files ngalo myalelo ulandelayo: git clone https://github.com/rm-hull/luma.examples.git
cd luma.examples python3 setup.py ufake
www.joy-it.net Pascalstr. 8 47506 Neukirchen-Vluyn

SPI-Interface
Iintambo

Iphini lokubonisa

I-Raspberry pin

Emva kokuba uqhagamshele umboniso, ungenza njengeample program enemiyalelo emibini ilandelayo:

cd ~/your_project/luma.exampngaphantsi/umzampkancinci/

python3 demo.py -i spi

www.joy-it.net Pascalstr. 8 47506 Neukirchen-Vluyn

I2C-Interface
Iintambo

Iphini lokubonisa

9 16

I-Raspberry Pin GND 5V GND iPin 5 iPin 3 iPin 3 3,3V

Emva kokuba uqhagamshele umboniso, ungenza njengeample nkqubo enemiyalelo emibini ilandelayo: cd ~/your_project/luma.exampngaphantsi/umzampkancinci/
python3 demo.py
www.joy-it.net Pascalstr. 8 47506 Neukirchen-Vluyn

5. ULWAZI OLONGEZELELWEYO
Ulwazi lwethu kunye nezibophelelo zokuthatha-umva ngokoMthetho weSixhobo soMbane kunye ne-Electronic (ElektroG)
Uphawu kwizixhobo zombane neze-elektroniki:
Lo mgqomo wothuli unqunyulwayo uthetha ukuba izixhobo zombane neze-elektroniki azikho kwinkunkuma yasekhaya. Kufuneka ubuyisele izixhobo ezidala kwindawo yokuqokelela. Ngaphambi kokunikezelwa kweebhetri zenkunkuma kunye neziqokeleli ezingavalwanga ngesixhobo senkunkuma kufuneka zohlulwe kuyo. Ukhetho lokubuyisela: Njengomsebenzisi wokugqibela, ungabuyisela isixhobo sakho esidala (esizalisekisa umsebenzi ofanayo nesixhobo esitsha esithengwe kuthi) simahla ukuze ulahlwe xa uthenga isixhobo esitsha. Izixhobo ezincinci ezingenayo imilinganiselo yangaphandle engaphezu kwama-25 cm zinokulahlwa kubungakanani bekhaya obuqhelekileyo ngaphandle kokuthengwa kwesixhobo esitsha. Ithuba lokubuyisela kwindawo yethu yenkampani ngexesha lokuvula: SIMAC Electronics GmbH, Pascalstr. 8, D-47506 Neukirchen-Vluyn, eJamani Ithuba lokubuyela kwindawo yakho: Siza kukuthumela ipasile stamp onokusibuyisela ngayo isixhobo ngaphandle kwentlawulo. Nceda uqhagamshelane nathi nge-imeyile Service@joy-it.net okanye ngomnxeba. Ulwazi malunga nokupakisha: Ukuba awunayo imathiriyeli yokupakisha efanelekileyo okanye awufuni ukusebenzisa eyakho, nceda uqhagamshelane nathi kwaye siya kukuthumelela ukupakishwa okufanelekileyo.
6. INKXASO Ukuba kusekho nayiphi na imiba elindileyo okanye iingxaki ezivela emva kokuthenga kwakho, siya kukuxhasa nge-imeyile, umnxeba kunye nenkqubo yethu yokuxhasa itikiti. I-imeyile: service@joy-it.net Inkqubo yamatikiti: https://support.joy-it.net Imfonomfono: +49 (0)2845 9360-50 (Mvulo – ngoLwesine: 09:00 – 17:00 intsimbi CET ,
NgoLwesihlanu: 09:00 – 14:30 o`clock CET) Ukuze ufumane inkcazelo engakumbi nceda undwendwele yethu webindawo: www.joy-it.net

Ipapashwe: 2024.03.20

SIMAwCwwElwwec.wjtor.oyjo-niytic.-nsiteG.tnmebt H PPaasscaalsltsrt.r8. ,8474570560N6eNuekuirkchirecnh-eVnlu-yVnluyn

Amaxwebhu / Izibonelelo

uvuyo-it COM-OLED2.42 Imodyuli yokuBonisa ye-OLED [pdf] Isikhokelo somsebenzisi
I-COM-OLED2.42 Imodyuli yokuBonisa i-OLED, i-COM-OLED2.42, iModyuli yokuBonisa i-OLED, iModyuli yokuBonisa, iModyuli

Iimbekiselo

Incwadi yokusebenzisa

I-COM-OLED2.42 Imodyuli yokuBonisa ye-OLED

Ulwazi lweMveliso

Iinkcukacha

ISabelo sePin soMboniso

Ukuseta iDisplay Interface

Imiyalelo yokusetyenziswa kwemveliso

Ukuqhagamshela iModyuli yokuBonisa

Ukunika amandla uMboniso

FAQ

Ndiyitshintsha njani indlela yolawulo yomboniso?

Amaxwebhu / Izibonelelo

Iimbekiselo

Shiya uluvo

Rhoxisa impendulo