Contents
hide
VON DUPRIN 7827 Surface Vertical Rod Exit Device
Product Information
- Model: 7827 Surface Vertical Rod Exit Device
- Devices Covered: 7827-F (Fire) Surface Vertical Rod Exit Device, CD7827 (Cylinder Dogging) Surface Vertical Rod Exit Device, QEL7827/27-F (Electric Latch Retraction) Surface Vertical Rod Exit Device
- Special Tools Needed: 5/64 hex wrench, #10-24 tap, Drill bits: #25, 1/8, 1/4, 5/16, 13/32
- Customer Service: 1-877-671-7011
- Website: www.allegion.com/us
Specifications
- Suitable for surface mount installation
- Compatible with various door thicknesses
- Includes necessary screws and bolts for installation
Product Usage Instructions
Installation
- Ensure you have all the special tools required for installation.
- Position the device template correctly on the door based on the door thickness.
- Mark and drill holes as per the Preparation Chart provided.
- Assemble the device according to the instructions provided.
- Adjust the tailpiece if needed for the door thickness.
Maintenance
Regularly inspect the device for any signs of wear or damage. Clean and lubricate moving parts as needed to ensure smooth operation.
Emergency Procedures
If the device malfunctions or becomes inoperable during an emergency situation, follow the emergency exit procedures defined for your building.
Frequently Asked Questions
- Q: What should I do if the device is not locking properly?
- A: Check the alignment of the device and ensure all components are securely fastened. If the issue persists, contact customer service for assistance.
- Q: Can I install this device on a metal door?
- A: Yes, the device is suitable for installation on both metal and wood doors. Follow the provided instructions for each door type.
Product Information
Devices covered by these instructions: 7827 Surface Vertical Rod Exit Device 7827-F (Fire) Surface Vertical Rod Exit Device CD7827 (Cylinder Dogging) Surface Vertical Rod Exit Device QEL7827/27-F (Electric Latch Retraction) Surface Vertical Rod Exit Device
Special tools needed:
- 5/64″ hex wrench
- #10-24 tap
- Drill bits: #25, 1/8″, 1/4″, 5/16″, 13/32″
SCREWCHART
PREPARATIONCHART
Go to instructions on next page before using the Preparation Chart
Installation Instruction
- Draw Horizontal Center Line (
) and Assemble Device Template
- Position Template as Shown and Mark Vertical
- Align Top and Bottom Templates Along and Prepare Door
- Adjust Tailpiece if Needed
Make sure tailpiece is installed at correct length for 1-3/4″ thick or 2-1/4″ thick door. If necessary, remove pine tree clip, rotate tailpiece, and reinstall pine tree clip.
- If Using a Cylinder, Remove Cam and Rotate 180˚
Cam must be in position shown with key removed. If necessary, remove cam screws, place cam is correct position, and reinstall cam screws.
- If Necessary, Install Cylinder
- If Using a Cylinder with a Tailpiece, Prepare Device and Cylinder
- Install Trim (if using) and Secure Device Center Case to Door
- Mark and Prepare 2 Holes for End Cap Bracket
- Install End Cap Bracket and End Cap
- Install Top Latch and Rod
- Install Top Strike
- Adjust Top Rod (Screw Rod Into or Out of Latch) Until Adjusted as Shown
- Install Bottom Strike, Latch, and Rod
- Adjust Bottom Rod with Door Open (Top Latch Retracted)
- Install Rod Guides and Covers
CUT TOP ROD
INSTALLRODEXTENSION
CD (CYLINDER DOGGING)
CUTDEVICE
Documents / Resources
 |
VON DUPRIN 7827 Surface Vertical Rod Exit Device [pdf] Instructions 7827, 7827-F, CD7827, QEL7827-27-F, 7827 Surface Vertical Rod Exit Device, 7827, Surface Vertical Rod Exit Device, Vertical Rod Exit Device, Rod Exit Device, Exit Device, Device |
 |
VON DUPRIN 7827 Surface Vertical Rod Exit Device [pdf] Installation Guide 7827, 7827-F, CD7827, QEL7827-27-F, HH-HW7827-27-F, 7827 Surface Vertical Rod Exit Device, 7827, Surface Vertical Rod Exit Device, Vertical Rod Exit Device, Rod Exit Device, Exit Device |
