Allegion US | Redefining Access Control & Commercial Security
Instructions for VON DUPRIN models including: 7827, 7827-F, CD7827, QEL7827-27-F, 7827 Surface Vertical Rod Exit Device, 7827, Surface Vertical Rod Exit Device, Vertical Rod Exit Device, Rod Exit Device, Exit Device, Device
31 mag 2024 — Devices covered by these instructions: 7827 Surface Vertical Rod Exit Device. 7827-F (Fire) Surface Vertical Rod Exit Device.8 pagine
Von Duprin Innovative Exit Devices | Library
File Info : application/pdf, 8 Pages, 1.24MB
DocumentDocument*47986706* 7827 47986706 Surface Vertical Rod Exit Device Installation Instructions Devices covered by these instructions: 7827 Surface Vertical Rod Exit Device 7827-F (Fire) Surface Vertical Rod Exit Device CD7827 (Cylinder Dogging) Surface Vertical Rod Exit Device QEL7827/27-F (Electric Latch Retraction) Surface Vertical Rod Exit Device Dogging Key (use with non-fire devices to lock down pushbar) Index: · Screw chart ............................. 2 · Preparation chart .................... 3 · Device installation ............... 4-6 · Cut top rod ............................. 7 · Install rod extension ................ 7 · Optional equipment ............... 8 · Cut device .............................. 8 Special tools needed: 5/64" hex wrench #10-24 tap Drill bits: #25, 1/8", 1/4", 5/16", 13/32" Customer Service 1-877-671-7011 www.allegion.com/us © Allegion 2024 Printed in U.S.A. 47986706 Rev. 04/24-a SCREW CHART A #10-24 X 1" Surface mount or Sex bolts (1-3/4" door) #10-24 X 1-1/2" Sex bolts (2-1/4" door) #10 x 1-1/4" Wood screw Surface mount (wood) - Packaged with trim - #10-24 X 1-3/8" #10-24 X 1-7/8" 785 trims (1-3/4" door) 785 trims (2-1/4" door) B #10-24 X 3/4" Surface mount or Sex bolts (1-3/4" door) #10-24 X 1-1/8" Sex bolts 2-1/4" door #10 x 1-1/4" Wood screw Surface mount (wood) C #10-16 x 3/8" Thread cutting D 1/4-20 X 3/4" 1/4-20 X 1-1/4" End cap 1-3/4" door 2-1/4" door E #10-24 X 3/4" Metal frame #10 x 1-1/2" Wood screw Wood frame F #10-12 x 10-24 x 1-1/4" Combination Metal or wood frame G #10-12 x 10-24 x 1-1/4" Combination Variable floor surfaces H #8-32 X 1/4" Latch covers I #10-12 x 10-24 x 1" Combination Metal or wood door J #8-18 x 3/8" Thread cutting Center case cover 2 Wood Metal PREPARATION CHART Go to instructions on next page before using Preparation Chart Top strike Wood Metal Latches 5/16" Drill (device side) 13/32" Drill (trim side) 13/32" Drill thru #25 Drill #10-24 Tap 1/8" Drill pilot 1" deep *Rod guides #25 Drill #10-24 Tap Wood Metal 1/8" Drill pilot 1" deep *Use rod guide as a template to mark holes Center case - 4 holes Surface mount *Sex bolts or trims Wood Metal Wood Metal X #25 Drill 1/4" Drill (device side) #10-24 tap 13/32" Drill (trim side) CL 1/8" Drill 13/32" CL pilot 1" deep Drill thru X *End cap bracket - 2 holes Surface mount **Sex bolts #25 Drill #10-24 tap 1/4" Drill (device side) 13/32" Drill (trim side) 1/8" Drill pilot 1" deep 13/32" Drill thru * Prepare holes after lock side of device is mounted and hinge side is leveled Door cut-outs Outside cylinder and trim applications: Mark with template and cut-out: Metal door(cut device side) Wood door(cut thru) Wood Metal Wood Metal Bottom strike Wood Metal #25 Drill #10-24 Tap See template for strike variations 1/8" Drill pilot 1" deep 3 1 Draw Horizontal Center Line ( ) and Assemble Device Template Device template 4 Adjust Tailpiece if Needed Make sure tailpiece is installed at correct length for 1-3/4" thick or 2-1/4" thick door. If necessary, remove pine tree clip, rotate tailpiece, and reinstall pine tree clip. 39/" to finished floor RHR RHR shown (LHR opposite) 2 Position Template as Shown and Mark Vertical C Vertical 2³/" Standard backset For 7827 single and double door Pine tree clip Tailpiece 1-3/4" door 2-1/4" door 5 If Using a Cylinder, Remove Cam and Rotate 180° Cam must be in position shown with key removed. If necessary, remove cam screws, place cam is correct position, and reinstall cam screws. Standard Orientation with key removed. Rotate cam if necessary as shown here. 3 Align Top and Bottom Templates Along CL and Prepare Door See "Preparation Chart" on page 3 for drill, tap, and cut-out information Top template For NL and E-trims, use this orientation. 6 If Necessary, Install Cylinder Plastic template See trim instructions for pull side door preparation. Line X-X in trim instructions is same as vertical device CL . 1-1/8 - 1-1/4" (29-32 mm) Bottom template 1-3/8 - 1-1/2" (35-38 mm) 4 7 10 If Using a Cylinder with a Tailpiece, Prepare Device Install End Cap Bracket and End Cap and Cylinder a. Install tailpiece guide. Tailpiece guide Secure end cap bracket and end cap Trim output B tailpiece C 11 Install Top Latch and Rod 8 Install Trim (if using) and Secure Device Center Case to Door 1-1/2" Minimum clearance (with end cap removed) if device is too long for door, see "Cut Device" on back cover Ccaesneter See "Screw Chart" on page 2 for screw types and sizes A Trim (optional) Top latch D If top rod is too long, see "Cut Top Rod" on page 7 If top rod is too short, see "Install Rod Extension" on page 7 Top rod (longer of the two) 9 Mark and Prepare 2 Holes for End Cap Bracket 12 Install Top Strike End cap bracket flush Level device 299/299F strike 3/16" Shim to 3/16" as shown #325 sex bolts (required) 260U strike F See "Preparation Chart" on page 3 for preparation information Mark and prepare 2 mounting holes Strike plate (299 only) E 499F strike (for LBR devices) See instruction 911009 5 13 15 Adjust Top Rod (Screw Rod Into or Out of Latch) Until Adjust Bottom Rod with Door Open (Top Latch Adjusted as Shown Retracted) With door closed: Latch bolt deadlocked (will not push in) With door open: Latch bolt stays retracted With door open: With door closed: Release trigger extended Latch bolt should clear floor and not bind on strike Latch bolt should be deadlocked (will not push in) Open and close door a few times and check for deadlatching when door is closed. Readjust rods if needed. 14 Install Bottom Strike, Latch, and Rod 248L-4 strike 16 Install Rod Guides and Covers G Shim (as needed to engage latch) 304L strike Grout strike into floor Bottom rod D Bottom latch #325 sexbolts (required) (topDloaotcrhorpeetrnacted) Hurricane applications use threshold with 304L bottom strike H Latch cover (2) *Rod guide (2) I Remove blue film J Install at midpoint of each rod *See "Preparation Chart" on page 3 304L strike grouted into floor 6 Threshold 1¼" min. embed Center case cover CUT TOP ROD 1. Measure amount to cut off rod as shown below. Note: Rod cutting is required for doors shorter than 7'. 2. Cut rod. Amount to cut off Actual door opening height *84" *Rods are factory sized for 7' (84") door. Measure actual door opening height and subtract that number from 84" to get amount to cut off top rod. Drive out roll pin 3. Drill new hole. Use cut off piece as a template 1/8" dia. drill thru 4. Reinstall rod end and roll pin. INSTALL ROD EXTENSION 1. Measure door opening to determine amount to cut off rod extension. Amount to cut off *Standard door heights: With no extension 7' (84") With 1' extension 8' (96") With 3' extension 10' (120") 2. Cut rod extension. Drive out roll pin 3. Drill new hole. Actual door opening height *96" OR *120" *Rods are factory sized for door heights shown above. Measure actual door opening height and subtract that number from 96" (for 1' extension) or 120" (for 3' extension) to get amount to cut off extension. Use metal template supplied with extension (on both sides of rod) 4. Reinstall rod end and roll pin. 1/8" dia. drill thru 5. Connect top rod and rod extension. Rod extension Top rod 7 OPTIONAL EQUIPMENT - CONTINUED CD (CYLINDER DOGGING) 1. Remove mortise cylinder cam and reinstall in reverse (Figure 1). 2. Insert key and rotate cam to install the cylinder to the cover plate (Figure 2). 3. Remove key to slide cover plate in position in the mechanism case. Std. mortise cylinder Std. mortise cylinder Offset toward pushbar Dogging plate cover Mortise cylinder cam Mortise cylinder cam CD function conversion Figure 1 Dogging procedure Turn cylinder key clockwise approx. 1/8 turn for standard dogging Depress pushbar Cylinder locating washer Figure 2 Std. mortise cylinder Cylinder collar Cylinder lock nut Mechanism case CUT DEVICE 1 Measure amount to cut off device. 1-1/2" minimum clearance (with endcap removed) Device aligned with mounting holes 2 Tape and mark area being cut. Remove anti-rattle clip Tape Note If 5/8" diameter wire access hole has been predrilled in door, cut device 5/16" from center of hole. 5/16" Cover plate (flush to pushbar) Pushbar 3 Cut device square. Cut device square and remove all burrs NOTE: Device must be cut square for proper end cap fit 4 Slide anti-rattle clip into device. 2" min. Anti-rattle clip inside 8