VANTOP SH180 Quick Start Guide User Manual

HP Projector SH180
QUICK START GUIDE

Technical Support: For more detailed usage instructions, please download the HP SH180 user manual at seeprojector.com

REMOTE

1. Power Button
2. Input Source
3. Navigation
4.  Home
5. Volume +/-
6. Focus
7. OK
8. Back
9. Settings
10. Shortcut to NETFLIX
11. Shortcut to YouTube
12. Shortcut to prime video

* Make sure you have installed two AAA batteries (not included) in the remote.
“Make sure the remote points at the IR receiver directly. Do not cover the IR receiver.

PROJECTOR INSTALLATION

Note:
The ceiling-mounting screw hole is located on the bottom of the projector.
Mounting Screw: 1/4″-8mm*1 (not included)

POWER ON/OFF

1. Take off the protective film.
2. Connect the power cord to the adapter and plug the cord into an outlet.
3. Press the Power button to turn on/off the projector.

FOCUS ADJUSTMENT

ToF Auto Focus
When the projector detects shaking/rapid movement, it will automatically adjust the image quality.
Electric/Manual Focus
Press the Focus button on the remote, then press the Up and Down buttons to sharpen the image focus until the blurry image becomes clear.

PROJECTOR CONNECTION AND INPUT SOURCE

Connect your device to the projector correctly, then select the right input source.
USB Connection: Insert the USB device, then press the button on the remote and select USB to ploy the file.
HDMI Connection: Connect the device, then press the button on the remote and select HDMI.
Wired Speaker and Headphones Connection: Not required to select any Input source.
USB Type-C Port: Supports power supply from a power bank (Minimum Output: 65W).
Note:
A 65W PD (20V/3.25A) or higher power bank and a 65W or higher USB-C to USB-C cable are required.

WIFI CONNECTION

Connect your projector to a wireless network by going to Homepage Setting > Network > Wi-Fi.

SCREEN MIRRORING

Important Note:
Copyrighted content from Hulu, Disney, or other similar streaming services CANNOT be wirelessly mirrored or cast due to copyright restrictions.
For iOS System
Step 1: Connect the projector and your mobile device to the same WiFi network.
Step 2: Go to Homepage > My Apps > APP assistant. Then select Screen Share and press OK on the remote to download and install the ScreenShare opp.
Note:
It is necessary to download the ScreenShare app for the initial setup.
Step 3: Go back to My Apps page, and launch the Screen Share app.
Step 4: Go to the Control Center of your iOS device, then tap Screen Mirroring to search for the projector
Step 5: Choose HP SH180 from the list, and once the connection is successful, the content on your IOS device will be mirrored onto the projector screen or wall.
For Android System
To activate this function, please make sure your Android device supports Multi-screen/Smart View/Wireless Display. Names vary on different Android devices.
Step 1: Go to the WiFi setting of your Android device to switch on the option of WiFi
Note:
It is not necessary to have a successful WiFi connection, but it is important to ensure that the WiFi is turned on in your Android device
Step 2: Go to Homepage > My Apps   > Screencast.
Step 3: Activate the Multi-screen/Smart View/Wireless Display function on your Android device and search for the projector.
Step 4: Choose HP SH180 from the list, and once the connection is successful the content on your Android device will be mirrored onto the projector screen or wall
DLNA
Step 1: Connect the projector and your mobile device to the same WIFI network.
Step 2: Go to Homepage > My Apps > HomeShare. Ensure the toggle is switched to On.
Step 3: Launch a video player app on your mobile device and select a video to
play.
Step 4: Tap to search for the projector and select HP SH180 to connect. The content on your device will be mirrored onto the projector screen or wall.
Note:
When you cast a video from your mobile device, the video will only be displayed on the projector screen and you can still use your mobile device without interrupting the video or showing any of your other content.

USING AS A BT SPEAKER

Use the projector as a BT speaker by connecting your mobile device to it through a BT connection.
Step 1: Homepage > My Apps >BT Speaker to make the projector ready for a BT connection.
Step 2: Access your mobile device’s BT settings and activate BT. Search for HP SH180 in the available devices list to pair your mobile device with the projector.

PROJECTION DISTANCE AND SIZE

• The recommended projection distance varies with different projection content. Please adjust the distance between the wall/screen and the projector as needed.
• For optimal image quality, we recommend a projection size of 100 inches.
• Position the projector 9.3 feet (2.83 m) away from the wall or screen.
• A dark environment will improve the clarity of the projected images.

TROUBLESHOOTING GUIDE

1. Can I directly use Netflix on the projector?
*Yes, you can. The projector comes with preinstalled and officially-licensed Netflix/YouTube/prime video apps. You have the convenience of watching your favorite videos directly on the projector without any hassle.
2. The content from Hulu and Disney can’t be mirrored when connected with smartphones./ Why is there audio but no video when streaming videos from my mobile phone to the projector via screen mirroring?
Due to the copyright restrictions from Hulu, Disney, and similar services, the content MAY NOT be mirrored or cost.
3. What should I do if the image is blurry?
Adjust the focus and correct the keystone distortion.
*It’s recommended to position the projector perpendicular to the screen at a distance of 9.3 feet (2.83m), with a projection size of 100 inches.
4. Why doesn’t the remote control work?
*Make sure the remote points at the IR receiver directly. Do not cover the IR receiver
*Make sure you have installed two AAA batteries in the remote control.
*Avoid mixing new batteries with old ones in the remote control as this can result in insufficient power supply and operational issues.
5. How to avoid audio lag when using BT?
To get rid of the log, we suggest you mirror your device to the projector via a wired connection. Additionally, please move your BT device closer to the projector in order to minimize Interference in the environment.
6. How do I flip the image?
*Go to Home > Settings > Projection to select the corresponding projection mode
7. How do I reset the projector?
*Go to Home > Settings > Setup Reset Default to restore the projector to default settings.
8. Con I sideload Android Apps onto the projector?
Sorry, you cannot sideload Android apps onto the projector.
9. How can I fix the black spot in the picture?
Project a white background picture and pause to freeze the display
Remove the dust cleaning cover on the top of the projector.
Insert a cotton swab deep inside and carefully wipe the sides of the LCD screen.
Reattach the cover after cleaning
10. The picture is not bright enough.
*You can try placing the projector closer to the wall to achieve higher brightness. For the best viewing experience, we suggest using the projector in a dark environment-the darker the room, the better the image quality.
11. Auto Focus/Auto Keystone is not working.
*Please restore the projector to factory settings and try again. If the issue still persists, please send a video to our customer service team via email for further assistance
12. Can I power the projector with a power bank?
*Yes. This projector supports temporary power supply from a 65W PD (20V/3.25A) or higher power bank via a 65W or higher USB-C to USB-C cable.
This is Ideal for use in places without power outlets, such as camping or outdoor movie watching. If the power bank’s output is insufficient, the projector may automatically reduce brightness or restart. This is a sign of inadequate power supply, not a product malfunction. For regular use please use the included power adapter to ensure stable brightness.
Please read the product instructions carefully before use.
Thank you for purchasing and using this product! For your safety and interests, please read the instructions carefully before using the product.
The trademarks and names mentioned in the manual are the property of their respective owners.
All instructions shown are for illustration purposes only. The actual product may vary due to product enhancements. We shall not be liable for any personal injury, property damage, or other damages caused due to failure to comply with the instructions or precautions

PRECAUTIONS

• Always place the projector on a fiat, stable surface
• Don’t look straight at the lens when it’s on
• If the projector gets wet, unplug it immediately.
• Don’t poke the projector with sharp objects
• Don’t cover the projector with cloth when it’s on.
• Use in clean, dust-free creas
• Use in darker environments for better viewing.
• It’s normal for the projector to vent worm oir as port of its normal cooling process to prevent overheating and maintain optimal performants.

SCREEN MIRRORING NOTE

Copyrighted content from Hulu, Disney, or other similar streaming services CANNOT be wirelessly mirrored or cost due to copyright restrictions

The terms HDMI HDMI High-Definition Multimedia Interface, HDMI Trade dress and the HDMI Logos are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.Dalby, Dolby Audio, and the double-D symbol are registered trademarks of Dolby Laboratories Licensing Corporation, Manufactured under license from Dolby Laboratories.The Bluetooth word mark and logos are registered trade Marius owned by Bluetooth SIG, Inc and any use of such marks by Shenzhen VanTop Technology & Innovation Co, Ltd under license. Other trademarks and trade nomes are those of their respective owners.
This device complies with port 15 of the FOC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful Interference, and (2) this device must accept any interference received, including interference that may cause undesired operation
Note: This equipment has been tested and found to comply with the limits for a Clase B digital device, pursuant to port 15 of the FCC rules. Those limits are designed to provide reasonable protection against harmful interference in a residential installation, This equipment generates, uses and conrodiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
Important: You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
RF Exposure Information:
– The radiated output power of this device meets the limits of FCC radio frequency exposure limits.
This device should be operated with a minimum separation distance of 20cm (8 inches) between the equipment and a person’s body.
Canada compliance statement:
This device complies with Innovation, Science and Economic Development Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:

1. this device may not cause interference, and
2. this device must accept any interference, including interference that may cause undesired operation of the device.

Operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems.
Exposure to radio frequency energy:
– The radiated output power of this device meets the limits of IC radio frequency exposure limits. This device should be operated with a minimum separation distance of 20 cm (8 inches) between the equipment and a person’s body.
CAN ICES (B) / NMB (B)
The symbol indicates DC voltage
The product label and certification information are located at the bottom of the product.
Use only the original or approved power adapter and power cable.
Power Input: 19.5V 6.15A or USB-C 20.0V 3.25A
Operating Temperature: 32°F-95°F (0°C-35°C)
Storage Temperature: -13°F-176°F (-25°C-80°C)

Scan for E-Manualshttps://qrs.ly/kmhf7re