BOARDCON Mini3568 Computer sa Module
Impormasyon ng Produkto
Mga pagtutukoy
| Tampok | Mga pagtutukoy |
|---|---|
| CPU | Quad-core Cortex-A55 |
| DDR | 2GB DDR4 (hanggang 8GB) |
| eMMC | 8GB (hanggang 128GB) |
| FLASH | DC 3.4~5V |
| kapangyarihan | Discrete Power sa board |
| LVDS / MIPI DSI | 2-CH LVDS o Du-LVDS, 2-CH MIPI DSI |
| I2S | 3-CH |
| MIPI CSI | 1-CH DVP at 2-CH 2-Lane CSI o 1-CH 4-Lane CSI |
| SATA | 3-CH |
| PCIe | 1-CH PCIe 2.0 at 1-CH PCIe 3.0 |
| Lumabas ang HDMI | 1-CH |
| MAAARI | 2-CH |
| USB | 2-CH(USB HOST2.0), 1-CH(OTG 2.0) at 1-CH(USB 3.0) |
| Ethernet | 2-ch GMAC: GMDI, GMII at QSGMII 1GB PHY (RTL8211F) sa core board |
| SDMMC/SDIO | 2-CH |
| SPDIF TX | 1-CH |
| I2C | 5-CH |
| SPI | 4-CH |
| UART | 8-CH, 1-CH(DEBUG) |
| PWM | 14-CH |
| ADC IN | 2-CH |
| Dimensyon ng Lupon | 70 x 58mm |
Mga Tagubilin sa Paggamit ng Produkto
Pag-set Up ng Mini3568 System-on-Module:
- Tiyaking ang Mini3568 system-on-module ay ligtas na naka-mount sa development board.
- Ikonekta ang mga kinakailangang peripheral gaya ng power input, display interface, USB device, at Ethernet cable sa kani-kanilang mga port sa Mini3568.
- I-on ang Mini3568 sa pamamagitan ng pagbibigay ng isang matatag na DC voltage sa loob ng tinukoy na hanay (3.4~5V).
- Ang sistema ay handa na para gamitin. Sundin ang iyong partikular na mga kinakailangan sa aplikasyon upang magamit nang epektibo ang Mini3568.
Mga Madalas Itanong (FAQ)
- T: Ano ang mga pangunahing aplikasyon ng Mini3568 system-on-module?
A: Ang Mini3568 ay idinisenyo para sa iba't ibang application kabilang ang mga pang-industriyang controller, IoT device, intelligent interactive na device, personal na computer, at robot. - Q: Ano ang maximum na kapasidad ng RAM na sinusuportahan ng Mini3568?
A: Sinusuportahan ng Mini3568 ang DDR4 RAM na may kapasidad na hanggang 8GB.
Panimula
Tungkol sa Manwal na ito
Ang manwal na ito ay inilaan upang bigyan ang gumagamit ng isang overview ng board at mga benepisyo, kumpletong mga detalye ng feature, at mga pamamaraan sa pag-set-up. Naglalaman din ito ng mahalagang impormasyon sa kaligtasan.
Feedback at Update sa Manwal na ito
- Upang matulungan ang aming mga customer na masulit ang aming mga produkto, patuloy kaming gumagawa ng mga karagdagang at na-update na mapagkukunan na magagamit sa Boardcon weblugar (www.boardcon.com, www.armdesigner.com).
- Kabilang dito ang mga manual, application notes, programming examples, at na-update na software at hardware. Mag-check-in nang pana-panahon upang makita kung ano ang bago!
- Kapag inuuna namin ang trabaho sa mga na-update na mapagkukunang ito, ang feedback mula sa mga customer ang numero unong impluwensya, Kung mayroon kang mga tanong, komento, o alalahanin tungkol sa iyong produkto o proyekto, mangyaring huwag mag-atubiling makipag-ugnayan sa amin sa support@armdesigner.com.
Limitadong Warranty
- Ginagarantiyahan ng Boardcon na ang produktong ito ay walang mga depekto sa materyal at pagkakagawa sa loob ng isang taon mula sa petsa ng pagbili. Sa panahon ng warranty na ito, aayusin o papalitan ng Boardcon ang sira na unit sa ilalim ng sumusunod na proseso:
- Dapat may kasamang kopya ng orihinal na invoice kapag ibinalik ang may sira na unit sa Boardcon. Ang limitadong warranty na ito ay hindi sumasaklaw sa mga pinsalang dulot ng pag-iilaw o iba pang power surge, maling paggamit, pang-aabuso, abnormal na kondisyon ng operasyon, o pagtatangka na baguhin o baguhin ang function ng produkto.
- Ang warranty na ito ay limitado sa pag-aayos o pagpapalit ng sira na unit. Sa anumang pagkakataon ay mananagot o mananagot ang Boardcon sa anumang pagkawala o pinsala, kabilang ang ngunit hindi limitado sa anumang nawalang kita, hindi sinasadya o kinahinatnang pinsala, pagkawala ng negosyo, o inaasahang kita na nagmumula sa paggamit o kawalan ng kakayahang gamitin ang produktong ito.
- Ang mga pagsasaayos na ginawa pagkatapos ng pag-expire ng panahon ng warranty ay napapailalim sa singil sa pagkumpuni at ang halaga ng pagbabalik ng pagpapadala. Mangyaring makipag-ugnayan sa Boardcon upang ayusin ang anumang serbisyo sa pagkukumpuni at makakuha ng impormasyon sa singil sa pagkukumpuni.
Buod
- Ang Mini3568 system-on-module ay nilagyan ng RK3568 ng Rockchip. Mayroon itong quad-core Cortex-A55, Mali-G52 GPU, at 0.8TOPs NPU.
- Partikular itong idinisenyo para sa mga AI device gaya ng mga pang-industriyang controller, IoT device, intelligent interactive na device, personal computer, at robot. Ang high-performance at low-power solution ay makakatulong sa mga customer na magpakilala ng mga bagong teknolohiya nang mas mabilis at mapahusay ang pangkalahatang kahusayan sa solusyon.
- Sa partikular, ang Mini3568 ay gumagamit ng DDR4 na may ECC para sa 7*24h na trabaho.
Mga tampok
- Microprocessor
- Quad-core Cortex-A55 hanggang 1.8GHz
- 32KB I-cache at 32KB D-cache para sa bawat core, 512KB L3 cache
- Mali-G52 hanggang 0.8GHz
- 1.0 TOPS Neural Process Unit
Organisasyon ng Memorya - DDR4 RAM hanggang 8GB
- EMMC hanggang 128GB
- Boot ROM
- Sinusuportahan ang pag-download ng system code sa pamamagitan ng USB OTG o SD
- Trust Execution Environment system
- Sinusuportahan ang secure na OTP at maramihang cipher engine
- Video Decoder/Encoder
- Sinusuportahan ang pag-decode ng video hanggang sa 4K @ 60fps
- Sinusuportahan ang H.264 encode
- H.264 HP encoding hanggang 1080p@30fps
- Laki ng larawan hanggang 8192×8192
- Display Subsystem
- Output ng Video
- Sinusuportahan ang HDMI 2.0 transmitter na may HDCP 1.4/2.2, hanggang 4K@60fps
- Sinusuportahan ang 8/4 lane MIPI DSI hanggang 2560×1440@60fps
- O interface ng Du-LVDS hanggang 1920×1080@60fps
- Sinusuportahan ang interface ng ePD1.3 hanggang 2560×1600@30fps
- Sinusuportahan ang BT-656 8bit na output
- Sinusuportahan ang BT-1120 16bit na output
- Suportahan ang 24bits RGB TTL output
- Suportahan ang tatlong display na may iba't ibang pinagmulan
- Input ng Larawan
- Sinusuportahan ang MIPI CSI 4lanes interface o 2ch MIPI CSI 2lanes interface
- Sinusuportahan ang 8~16bit na DVP interface
- Sinusuportahan ang BT-656 8bit na input
- Sinusuportahan ang BT-1120 8~16bit na input
- Output ng Video
- I2S/PCM
- Tatlong interface ng I2S/PCM
- Suportahan ang Mic array Hanggang 8ch PDM/TDM interface
- Isang SPDIF output
- USB at PCIE
- Tatlong 2.0 USB interface
- Tatlong SATA interface
- O QSGMII + Isang USB3.0 host.
- O Dalawang USB3.0 host + Isang 1 lane PCIe 2.0.
- Isang interface ng PCIe 3.0
- Ethernet
- Nakasakay ang RTL8211F
- Suportahan ang GMAC/EMAC at QSGMII
- Suportahan ang 10/100/1000Mbit/s mga rate ng paglilipat ng data
- Suportahan ang dual ethernet
- I2C
- Hanggang Limang I2C
- Suportahan ang standard mode at fast mode (hanggang 400kbit/s)
- SDIO
- Suportahan ang SDIO 3.0 protocol
- SPI
- Hanggang apat na SPI controllers,
- Full-duplex synchronous serial interface
- UART
- Suportahan ang hanggang 9 na UART
- UART2 na may 2 wire para sa mga tool sa pag-debug
- Naka-embed ng dalawang 64byte FIFO
- Suportahan ang auto flow control mode para sa UART1-5
- SATA
- Tatlong SATA host controller
- Suportahan ang SATA 1.5Gb/s, 3.0Gb/s at SATA 6.0Gb/s
- ADC
- Hanggang dalawang ADC channel
- 10-bit na resolution
- Voltage input range sa pagitan ng 0V hanggang 1.8V
- Suportahan ang hanggang 1MS/ssampling rate
- PWM
- 14 on-chip PWM na may interrupt-based na operasyon
- Suportahan ang 32bit time/counter facility
- IR na opsyon sa PWM3/7/11/15
- Power unit
- Discrete Power sa board
- Single 3.4-5V input
- Napakababang kumonsumo ng kasalukuyang RTC, mas mababa ang 5uA sa 3V Button Cell
- 3.3V output max 500mA
I-block ang Diagram
RK3568 Block Diagram
Development board Block Diagram
Mga pagtutukoy
| Tampok | Mga pagtutukoy |
| CPU | Quad-core Cortex-A55 |
| DDR | 2GB DDR4 (hanggang 8GB) |
| eMMC FLASH | 8GB (hanggang 128GB) |
| kapangyarihan | DC 3.4~5V |
| LVDS / MIPI DSI | 2-CH LVDS o Du-LVDS, 2-CH MIPI DSI |
| I2S | 3-CH |
| MIPI CSI | 1-CH DVP at 2-CH 2-Lane CSI o 1-CH 4-Lane CSI |
| SATA | 3-CH |
| PCIe | 1-CH PCIe 2.0 at 1-CH PCIe 3.0 |
| Lumabas ang HDMI | 1-CH |
| MAAARI | 2-CH |
| USB | 2-CH (USB HOST2.0), 1-CH(OTG 2.0) at 1-CH(USB 3.0) |
| Ethernet | 2-ch GMAC: GMDI, GMII at QSGMII
1GB PHY (RTL8211F) sa core board. |
| SDMMC/SDIO | 2-CH |
| SPDIF TX | 1-CH |
| I2C | 5-CH |
| SPI | 4-CH |
| UART | 8-CH, 1-CH(DEBUG) |
| PWM | 14-CH |
| ADC IN | 2-CH |
| Dimensyon ng Lupon | 70 x 58mm |
Dimensyon ng PCB
Kahulugan ng Pin
| J1 | Signal | Paglalarawan o mga function | GPIO serial | IO Voltage |
| 1 | HDMI_TXCN | 0.5V | ||
| 2 | HDMI_TX0N | 0.5V | ||
| 3 | HDMI_TXCP | 0.5V | ||
| 4 | HDMI_TX0P | 0.5V | ||
| 5 | GND | Lupa | 0V | |
| 6 | GND | Lupa | 0V | |
| 7 | HDMI_TX1N | 0.5V |
| 8 | HDMI_TX2N | 0.5V | ||
| 9 | HDMI_TX1P | 0.5V | ||
| 10 | HDMI_TX2P | 0.5V | ||
| 11 | HDMI_HPD | HDMI HPD input | 3.3V | |
| 12 | HDMI_CEC | HDMI_CEC/SPI3_CS1_M1 | GPIO4_D1_u | 3.3V |
| 13 | I2C_SDA_HDMI | I2C5_SDA_M1 | GPIO4_D0_u | 3.3V |
| 14 | I2C_SCL_HDMI | I2C5_SCL_M1 | GPIO4_C7_u | 3.3V |
| 15 | GND | Lupa | 0V | |
|
16 |
LCDC_VSYNC/
UART5_TX_M1 |
VOP_BT1120_D14/SPI1_MI
SO_M1/I2S1_SDO3_M2 |
GPIO3_C2_d |
3.3V |
|
17 |
LCDC_HSYNC/
PCIE20_PERSTn_M1 |
VOP_BT1120_D13/SPI1_MO
SI_M1/I2S1_SDO2_M2 |
GPIO3_C1_d |
3.3V |
|
18 |
LCDC_CLK/
UART8_RX_M1 |
VOP_BT1120_CLK/SPI2_CL
K_M1/I2S1_SDO1_M2 |
GPIO3_A0_d |
3.3V |
|
19 |
LCDC_DEN/
UART5_RX_M1 |
VOP_BT1120_D15/SPI1_CL
K_M1/I2S1_SCLK_RX_M2 |
GPIO3_C3_d |
3.3V |
| 20 | LVDS_MIPI_TX_D0P | LVDS0 o MIPI0 DSI D0P TX | Tandaan(1) | 0.5V |
| 21 | LVDS_MIPI_TX_D0N | LVDS0 o MIPI0 DSI D0N TX | Tandaan(1) | 0.5V |
| 22 | LVDS_MIPI_TX_D1P | LVDS0 o MIPI0 DSI D1P TX | Tandaan(1) | 0.5V |
| 23 | LVDS_MIPI_TX_D1N | LVDS0 o MIPI0 DSI D1N TX | Tandaan(1) | 0.5V |
| 24 | LVDS_MIPI_TX_D2P | LVDS0 o MIPI0 DSI D2P TX | Tandaan(1) | 0.5V |
| 25 | LVDS_MIPI_TX_D2N | LVDS0 o MIPI0 DSI D2N TX | Tandaan(1) | 0.5V |
| 26 | LVDS_MIPI_TX_D3P | LVDS0 o MIPI0 DSI D3P TX | Tandaan(1) | 0.5V |
| 27 | LVDS_MIPI_TX_D3N | LVDS0 o MIPI0 DSI D3N TX | Tandaan(1) | 0.5V |
|
28 |
LCDC_D8/GPIO3_A1 |
VOP_BT1120_D0/SPI1_CS0
_M1/PCIe30x1_PERSTn_M1 |
GPIO3_A1_d |
3.3V |
|
29 |
LCDC_D9/I2S3_MCLK
_M0 |
VOP_BT1120_D1 |
GPIO3_A2_d |
3.3V |
|
30 |
LVDS_MIPI_TX_CLKP |
LVDS0 o MIPI0 DSI CLKP
TX |
Tandaan(1) |
0.5V |
|
31 |
LVDS_MIPI_TX_CLKN |
LVDS0 o MIPI0 DSI CLKN
TX |
Tandaan(1) |
0.5V |
|
32 |
LCDC_D10/I2S3_SCL
K_M0 |
VOP_BT1120_D2 |
GPIO3_A3_d |
3.3V |
|
33 |
LCDC_D11/I2S3_LRCK
_M0 |
VOP_BT1120_D3 |
GPIO3_A4_d |
3.3V |
|
34 |
LCDC_D12/I2S3_SDO
_M0 |
VOP_BT1120_D4 |
GPIO3_A5_d |
3.3V |
|
35 |
LCDC_D13/I2S3_SDI_
M0 |
VOP_BT1120_CLK |
GPIO3_A6_d |
3.3V |
| 36 | LCDC_D14/GPIO3_A7 | VOP_BT1120_D5 | GPIO3_A7_d | 3.3V |
| 37 | LCDC_D15/GPIO3_B0 | VOP_BT1120_D6 | GPIO3_B0_d | 3.3V |
|
38 |
LCDC_D16/UART4_RX
_M1 |
VOP_BT1120_D7/PWM8_M
0 |
GPIO3_B1_d |
3.3V |
|
39 |
LCDC_D17/UART4_TX
_M1 |
VOP_BT1120_D8/PWM9_M
0 |
GPIO3_B2_d |
3.3V |
|
40 |
LCDC_D18/I2C5_SCL_
M0 |
VOP_BT1120_D9/PDM_SDI
0_M2 |
GPIO3_B3_d |
3.3V |
|
41 |
LCDC_D19/I2C5_SDA
_M0 |
VOP_BT1120_D10/PDM_SD
I1_M2 |
GPIO3_B4_d |
3.3V |
|
42 |
LCDC_D20/GPIO3_B5 |
VOP_BT1120_D11/PWM10_
M0/I2C3_SCL_M1 |
GPIO3_B5_d |
3.3V |
|
43 |
LCDC_D21/PWM11_IR
_M0 |
VOP_BT1120_D12/I2C3_SD
A_M1 |
GPIO3_B6_d |
3.3V |
| 44 | GND | Lupa | 0V | |
| 45 | MIPI_CSI_RX_CLK0N | 0.5V | ||
| 46 | MIPI_CSI_RX_D0P | 0.5V | ||
| 47 | MIPI_CSI_RX_CLK0P | 0.5V | ||
| 48 | MIPI_CSI_RX_D0N | 0.5V | ||
| 49 | MIPI_CSI_RX_D2N | MIPI_CSI_RX1_D0N | 0.5V | |
| 50 | MIPI_CSI_RX_D1N | 0.5V | ||
| 51 | MIPI_CSI_RX_D2P | MIPI_CSI_RX1_D0P | 0.5V | |
| 52 | MIPI_CSI_RX_D1P | 0.5V | ||
| 53 | MIPI_CSI_RX_D3P | MIPI_CSI_RX1_D1P | 0.5V | |
| 54 | GND | Lupa | 0V | |
| 55 | MIPI_CSI_RX_D3N | MIPI_CSI_RX1_D1N | 0.5V | |
| 56 | MIPI_CSI_RX_CLK1N | MIPI_CSI_RX1_CLKN | 0.5V | |
| 57 | RTC_CLKO_WIFI | RTC 32.768KHz CLK na output | 1.8V | |
| 58 | MIPI_CSI_RX_CLK1P | MIPI_CSI_RX1_CLKP | 0.5V | |
| 59 | GND | Lupa | 0V | |
|
60 |
CIF_D9_GMAC1_TXD
3_M1_1V8 |
EBC_SDDO9/UART1_RX_M
1/PDM_SDI0_M1 |
GPIO3_D7_d |
1.8V |
|
61 |
CIF_D8_GMAC1_TXD
2_M1_1V8 |
EBC_SDDO8/UART1_TX_M
1/PDM_CLK0_M1 |
GPIO3_D6_d |
1.8V |
|
62 |
CIF_D11_GMAC1_RX
D2_M1_1V8 |
EBC_SDDO11/PDM_SDI1_
M1 |
GPIO4_A1_d |
1.8V |
|
63 |
CIF_D10_GMAC1_TX
CLK_M1_1V8 |
EBC_SDDO10/PDM_CLK1_
M1 |
GPIO4_A0_d |
1.8V |
|
64 |
CIF_D13_GMAC1_RX
CLK_M1_1V8 |
EBC_SDDO13/UART7_RX_
M2/PDM_SDI3_M1 |
GPIO4_A3_d |
1.8V |
|
65 |
CIF_D12_GMAC1_RX
D3_M1_1V8 |
EBC_SDDO12/UART7_TX_
M2/PDM_SDI2_M1 |
GPIO4_A2_d |
1.8V |
|
66 |
CIF_D15_GMAC1_TX
D1_M1_1V8 |
EBC_SDDO15/UART9_RX_
M2/I2S2_LRCK_RX_M1 |
GPIO4_A5_d |
1.8V |
|
67 |
CIF_D14_GMAC1_TX
D0_M1_1V8 |
EBC_SDDO14/UART9_TX_
M2/I2S2_LRCK_TX_M1 |
GPIO4_A4_d |
1.8V |
|
68 |
GMAC1_TXEN_M1_1V
8 |
EBC_SDCE0/SPI3_CS0_M0/
I2S1_SCK_RX_M1 |
GPIO4_A6_d |
1.8V |
|
69 |
GMAC1_RXD0_M1_1V
8/CAM_CLKOUT0 |
EBC_SDCE1/SPI3_CS1_M0/
I2S1_LRCK_RX_M1 |
GPIO4_A7_d |
1.8V |
|
70 |
GMAC1_RXD1_M1_1V
8/CAM_CLKOUT1 |
EBC_SDCE2/SPI3_MISO_M
0/I2S1_SDO1_M1 |
GPIO4_B0_d |
1.8V |
|
71 |
GMAC1_RXDV_CRS_
M1_1V8 |
EBC_SDCE3/I2S1_SDO2_M
1 |
GPIO4_B1_d |
1.8V |
|
72 |
CIF_HREF_GMAC1_M
DC_M1_1V8 |
EBC_SDLE/UART1_RTS_M
1/I2S2_MCLK_M1 |
GPIO4_B6_d |
1.8V |
|
73 |
CIF_VSYNC_GMAC1_
MDIO_M1_1V8 |
EBC_SDOE/I2S2_SCK_TX_
M1 |
GPIO4_B7_d |
1.8V |
|
74 |
CIF_CLKOUT/PWM11_
IR_M1_1V8 |
EBC_GDCLK |
GPIO4_C0_d |
1.8V |
|
75 |
CIF_CLKIN_GMAC1_M
CLKINOUT_M1_1V8 |
EBC_SDCLK/UART1_CTS_
M1/I2S2_SCK_RX_M1 |
GPIO4_C1_d |
1.8V |
|
76 |
I2C4_SCL_M0_1V8/ET
H1_CLKO_25M_M1 |
EBC_GDOE/SPI3_CLK_M0/I
2S2_SDO_M1 |
GPIO4_B3_d (Hilahin pataas
2.2K onboard) |
1.8V |
|
77 |
I2C4_SDA_M0_1V8/G
MAC1_RXER_M1 |
EBC_VCOM/SPI3_MOSI_M0
/I2S2_SDI_M1 |
GPIO4_B2_d (Hilahin pataas
2.2K onboard) |
1.8V |
| 78 | GND | Lupa | 0V | |
| 79 | EDP_TX_D1N | 0.5V | ||
| 80 | EDP_TX_D0N | 0.5V | ||
| 81 | EDP_TX_D1P | 0.5V | ||
| 82 | EDP_TX_D0P | 0.5V | ||
|
83 |
PHY_LED2/CFG_LDO
1 |
LINK LED+ |
3.3V |
|
|
84 |
PHY_LED1/CFG_LDO
0 |
BILIS LED- |
3.3V |
|
| 85 | EDP_TX_AUXN | 0.5V | ||
| 86 | EDP_TX_AUXP | 0.5V | ||
| 87 | PCIE20_TXP | O SATA2/QSGMII_TXP | 0.5V | |
| 88 | SARADC_VIN2_1V8 | 1.8V | ||
| 89 | PCIE20_TXN | O SATA2/QSGMII_TXN | 0.5V | |
|
90 |
SARADC_VIN0/RECO
VERY_1V8 |
I-recover ang Key input |
(Pull up10K onboard) |
1.8V |
| 91 | GPIO0_A0_d | REFCLK_OUT | 3.3V | |
| 92 | PCIE20_RXP | O SATA2/QSGMII_RXP | 0.5V | |
| 93 | PCIE20_REFCLKP | 0.5V | ||
| 94 | PCIE20_RXN | O SATA2/QSGMII_RXN | 0.5V |
| 95 | PCIE20_REFCLKN | 0.5V | ||
| 96 | VCC_RTC | VCC_RTC Power input | 1.8-3.3V | |
| 97 | VCC3V3_SYS | 3V3 IO output para sa Carry board | Pinakamataas na 500mA | 3.3V |
| 98 | GND | Lupa | 0V | |
| 99 | VCC3V3_SYS | 3V3 IO output para sa Carry board | 3.3V | |
| 100 | GND | Lupa | 0V |
| J2 | Signal | Paglalarawan o mga function | GPIO serial | IO Voltage |
| 1 | VCC_SYS | 3.3-5V Main Power input | 3.4-5V | |
| 2 | GND | Lupa | 0V | |
| 3 | VCC_SYS | 3.3-5V Main Power input | 3.4-5V | |
| 4 | GND | Lupa | 0V | |
| 5 | PMIC_EN | Power On Control signal | Tandaan(3) | 3.4-5V |
| 6 | PHY_MDI0+ | 0.5V | ||
| 7 | PHY_MDI1+ | 0.5V | ||
| 8 | PHY_MDI0- | 0.5V | ||
| 9 | PHY_MDI1- | 0.5V | ||
|
10 |
PWM3_IR |
EPD_HPDIN_M1/PCIE30x1_
WAKEn_M0 |
GPIO0_C2_d |
3.3V |
| 11 | PHY_MDI2+ | 0.5V | ||
| 12 | PHY_MDI3+ | 0.5V | ||
| 13 | PHY_MDI2- | 0.5V | ||
| 14 | PHY_MDI3- | 0.5V | ||
| 15 | GND | Lupa | 0V | |
|
16 |
SPDIF_TX_M0 |
UART4_RX_M0/PDM_CLK1
_M0/I2S1_SCLK_RX_M0 |
GPIO1_A4_d |
3.3V |
|
17 |
CIF_D4_SDMMC2_CM
D_M0_1V8 |
EBC_SDDO4/I2S1_SDI0_M1
/VOP_BT656_D4_M1 |
GPIO3_D2_d |
1.8V |
|
18 |
CIF_D0_SDMMC2_D0
_M0_1V8 |
EBC_SDDO0/I2S1_MCK_M1
/VOP_BT656_D0_M1 |
GPIO3_C6_d |
1.8V |
|
19 |
CIF_D1_SDMMC2_D1
_M0_1V8 |
EBC_SDDO1/I2S1_SCK_TX
_M1/VOP_BT656_D1_M1 |
GPIO3_C7_d |
1.8V |
|
20 |
CIF_D2_SDMMC2_D2
_M0_1V8 |
EBC_SDDO2/I2S1_LRCK_T
X_M1/VOP_BT656_D2_M1 |
GPIO3_D0_d |
1.8V |
|
21 |
CIF_D3_SDMMC2_D3
_M0_1V8 |
EBC_SDDO3/I2S1_SDO0_M
1/VOP_BT656_D3_M1 |
GPIO3_D1_d |
1.8V |
|
22 |
CIF_D5_SDMMC2_CL
K_M0_1V8 |
EBC_SDDO5/I2S1_SDI1_M1
/VOP_BT656_D5_M1 |
GPIO3_D3_d |
1.8V |
|
23 |
CIF_D6_1V8 |
EBC_SDDO6/I2S1_SDI2_M1
/VOP_BT656_D6_M1 |
GPIO3_D4_d |
1.8V |
|
24 |
CIF_D7_1V8 |
EBC_SDDO7/I2S1_SDI2_M1
/VOP_BT656_D7_M1 |
GPIO3_D5_d |
1.8V |
|
25 |
CAN2_RX_M0_1V8 |
EBC_GDSP/I2C2_SDA_M1/
VOP_BT656_CLK_M1 |
GPIO4_B4_d |
1.8V |
|
26 |
CAN2_TX_M0_1V8 |
EBC_SDSHR/I2C2_SCL_M1
/I2S_SDO3_M1 |
GPIO4_B5_d |
1.8V |
| 27 | GPIO2_C1_d_1V8 | GPIO2_C1_d | 1.8V | |
| 28 | GPIO0_D6_d_1V8 | GPIO0_D6_d | 1.8V | |
|
29 |
SPI0_CLK_M0 |
PCIe20_WAKE_M0/PWM1_
M1/I2C2_SCL_M0 |
GPIO0_B5_u |
3.3V |
|
30 |
SPI0_CS0_M0 |
PCIe30x2_PERST_M0/PWM
7_IR_M1 |
GPIO0_C6_d |
3.3V |
|
31 |
SPI0_MISO_M0 |
PCIe30x2_WAKE_M0/PWM6
_M1 |
GPIO0_C5_d |
3.3V |
|
32 |
SPI0_MOSI_M0 |
PCIe20_PERST_M0/PWM2_
M1/I2C2_SDA_M0 |
GPIO0_B6_u |
3.3V |
|
33 |
UART7_RX_M1 |
SPDIF_TX_M1/I2S1_LRCK_
RX_M2/PWM15_IR_M0 |
GPIO3_C5_d |
3.3V |
|
34 |
UART7_TX_M1 |
PDM_CLK1_M2/VOP_PWM
_M1/PWM14_M0 |
GPIO3_C4_d |
3.3V |
| 35 | UART8_RX_M0_1V8 | CLK32K_OUT1 | GPIO2_C6_d | 1.8V |
| 36 | UART8_TX_M0_1V8 | GPIO2_C5_d | 1.8V | |
| 37 | GND | Lupa | 0V | |
|
38 |
UART8_CTS_M0_1V8 |
CAN2_TX_M1/I2C4_SCL_M
1 |
GPIO2_B2_u |
1.8V |
| 39 | USB3_OTG0_DM | O ADB/debug USB port | 0.5V | |
|
40 |
UART8_RTS_M0_1V8 |
CAN2_RX_M1/I2C4_SDA_M
1 |
GPIO2_B1_d |
1.8V |
| 41 | USB3_OTG0_DP | O ADB/debug USB port | 0.5V | |
| 42 | USB3_OTG0_ID | 1.8V | ||
| 43 | USB3_HOST1_DM | 0.5V | ||
| 44 | USB3_OTG0_VBUS | VBUS DET input | 3.3V | |
| 45 | USB3_HOST1_DP | 0.5V | ||
| 46 | USB2_HOST3_DM | 0.5V | ||
|
47 |
SATA0_ACT_LED/UAR
T9_RX_M1 |
SPI3_CS0_M1/I2S3_SDI_M1
/PWM13_M1 |
GPIO4_C6_d |
3.3V |
| 48 | USB2_HOST3_DP | 0.5V | ||
|
49 |
CAN1_RX_M1/PWM14
_M1 |
SPI3_CLK_M1/I2S3_MCLK_
M1/PCIe30x2_CLKREQ_M2 |
GPIO4_C2_d |
3.3V |
| 50 | GND | Lupa | 0V | |
|
51 |
SATA1_ACT_LED/UAR
T9_TX_M1 |
SPI3_MISO_M1/I2S3_SDO_
M1/PWM12_M1 |
GPIO4_C5_d |
3.3V |
|
52 |
CAN1_TX_M1/PWM15
_IR_M1D |
SPI3_MOSI_M1/I2S3_SCLK
_M1/PCIe30x2_WAKE_M2 |
GPIO4_C3_d |
3.3V |
| 53 | GND | Lupa | 0V | |
|
54 |
SPDIF_TX_M2/SATA2_
ACT_LED |
EDP_HPD_M0/I2S3_LRCK_
M1/PCIe30x2_PERST_M2 |
GPIO4_C4_d |
3.3V |
| 55 | USB3_OTG0_SSRXN | O SATA0_RXN | 0.5V | |
| 56 | USB3_OTG0_SSTXN | O SATA0_TXN | 0.5V | |
| 57 | USB3_OTG0_SSRXP | O SATA0_RXP | 0.5V | |
| 58 | USB3_OTG0_SSTXP | O SATA0_TXP | 0.5V | |
| 59 | USB3_HOST1_SSRXP | O SATA1/QSGMII_RXP | 0.5V | |
| 60 | USB3_HOST1_SSTXP | O SATA1/QSGMII_TXP | 0.5V | |
| 61 | USB3_HOST1_SSRXN | O SATA1/QSGMII_RXN | 0.5V | |
| 62 | USB3_HOST1_SSTXN | O SATA1/QSGMII_TXN | 0.5V | |
|
63 |
SDMMC0_CLK |
UART5_TX_M0/CAN0_RX_
M1 |
GPIO2_A2_d |
3.3V |
| 64 | GND | Lupa | 0V | |
|
65 |
SDMMC_D0 |
UART2_TX_M1/UART6_TX_
M1/PWM8_M1 |
GPIO1_D5_u |
3.3V |
|
66 |
SDMMC_CMD |
UART5_RX_M0/CAN0_TX_
M1/PWM10_M1 |
GPIO2_A1_u |
3.3V |
| 67 | SDMMC_D2 | UART5_CTS_M0 | GPIO1_D7_u | 3.3V |
|
68 |
SDMMC_D1 |
UART2_RX_M1/UART6_RX
_M1/PWM9_M1 |
GPIO1_D6_u |
3.3V |
|
69 |
SDMMC_DET |
PCIe30x1_CLKREQ_M0/SAT
A_CP_DET |
GPIO0_A4_u |
3.3V |
| 70 | SDMMC_D3 | UART5_RTS_M0 | GPIO1_A0_u | 3.3V |
|
71 |
PCIE20_CLKREQn_M0
/GPIO0_A5 |
SATA_MP_SWITCH |
GPIO0_A5_d |
3.3V |
| 72 | LCD0_BL_PWM4 | PCIe30x1_PERST_M0 | GPIO0_C3_d | 3.3V |
|
73 |
LCD0_PWREN_H_GPI
O0_C7 |
HDMITX_CEC_M1/PWM0_M
1 |
GPIO0_C7_d |
3.3V |
| 74 | LCD1_BL_PWM5 | SPI0_CS1_M0 | GPIO0_C4_d | 3.3V |
|
75 |
I2S1_SDI0_M0/PDM_S
DI0_M0 |
GPIO1_B3_d |
3.3V |
|
|
76 |
I2S1_MCLK_M0 |
UART3_RTS_M0/SCR_CLK/
PCIe30x1_PERST_M2 |
GPIO1_A2_d |
3.3V |
|
77 |
I2S1_SCLK_TX_M0 |
UART3_CTS_M0/SCR_IO/P
CIe30x1_WAKE_M2 |
GPIO1_A3_d |
3.3V |
|
78 |
PDM_CLK0_M0 |
UART4_TX_M0/I2S1_LRCK
_RX_M0/AU_PWM_ROUTP |
GPIO1_A6_d |
3.3V |
|
79 |
I2S1_LRCK_TX_M0 |
UART4_RTS_M0/SCR_RST/
PCIe30x1_CLKREQ_M2 |
GPIO1_A5_d |
3.3V |
|
80 |
I2S1_SDO0_M0 |
UART4_CTS_M0/SCR_DET/
AU_PWM_ROUTN |
GPIO1_A7_d |
3.3V |
|
81 |
PDM_SDI1_M0_ADC |
I2S1_SDI1_SDO3_M0/PCIe2
0_PERST_M2 |
GPIO1_B2_d |
3.3V |
|
82 |
PDM_SDI2_M0_ADC |
I2S1_SDI2_SDO2_M0/PCIe2
0_WAKE_M2 |
GPIO1_B1_d |
3.3V |
|
83 |
PDM_SDI3_M0_ADC |
I2S1_SDI3_SDO1_M0/PCIe2
0_CLKREQ_M2 |
GPIO1_B0_d |
3.3V |
|
84 |
LCDC_D0/SPI0_MISO
_M1/I2S1_MCLK_M2 |
PCIe20_CLKREQ_M1/VOP_
BT656_D0_M0 |
GPIO2_D0_d |
3.3V |
|
85 |
I2C3_SDA_M0 |
UART3_RX_M0/CAN1_RX_
M0/AU_PWM_LOUTP |
GPIO1_A0_u |
3.3V |
| 86 | GND | Lupa | 0V | |
|
87 |
LCDC_D1/SPI0_MOSI
_M1/I2S1_SCK_Tx_M2 |
PCIe20_WAKE_M1/VOP_BT
656_D1_M0 |
GPIO2_D1_d |
3.3V |
|
88 |
I2C3_SCL_M0 |
UART3_TX_M0/CAN1_TX_
M0/AU_PWM_LOUTN |
GPIO1_A1_u |
3.3V |
|
89 |
I2C1_SDA/CAN0_RX_
M0 |
PCIe20_BUTTONRST/MCU_
JTAG_TCK |
GPIO0_B4_u(Hilahin pataas
2.2K) |
3.3V |
|
90 |
LCDC_D2/SPI0_CS0_ M1/I2S1_LRCK_TX_M
2 |
PCIe30x1_CLKREQ_M1/VO P_BT656_D2_M0 |
GPIO2_D2_d |
3.3V |
|
91 |
UART2_RX_M0_DEBU
G |
GPIO0_D0_u |
3.3V |
|
|
92 |
I2C1_SCL/CAN0_TX_
M0 |
PCIe30x1_BUTTONRST/MC
U_JTAG_TDO |
GPIO0_B3_u(Hilahin pataas
2.2K) |
3.3V |
|
93 |
LCDC_D23/UART3_RX
_M1 |
PDM_SDI3_M2/PWM13_M0 |
GPIO3_C0_d |
3.3V |
|
94 |
UART2_TX_M0_DEBU
G |
GPIO0_D1_u |
3.3V |
|
|
95 |
LCDC_D3/SPI0_CLK_
M1/I2S1_SDI0_M2 |
PCIe30x1_WAKE_M1/VOP_
BT656_D3_M0 |
GPIO2_D3_d |
3.3V |
|
96 |
LCDC_D22/UART3_TX
_M1 |
PDM_SDI2_M2/PWM12_M0 |
GPIO3_B7_d |
3.3V |
|
97 |
LCDC_D4/SPI0_CS1_
M1/I2S1_SDI1_M2 |
PCIe30x2_CLKREQ_M1/VO
P_BT656_D4_M0 |
GPIO2_D4_d |
3.3V |
|
98 |
LCDC_D5/SPI2_CS0_
M1/I2S1_SDI2_M2 |
PCIe30x2_WAKE_M1/VOP_
BT656_D5_M0 |
GPIO2_D5_d |
3.3V |
|
99 |
LCDC_D6/SPI2_MOSI
_M1/I2S1_SDI3_M2 |
PCIe30x2_PERST_M1/VOP
_BT656_D6_M0 |
GPIO2_D6_d |
3.3V |
|
100 |
LCDC_D7/SPI2_MISO
_M1/I2S1_SDO0_M2/U ART8_TX_M1 |
VOP_BT656_D7_M0 |
GPIO2_D7_d |
3.3V |
| J3 | Signal | Paglalarawan o mga function | GPIO serial | IO Voltage |
| 1 | MIPI_DSI_TX1_D3P | LVDS1 o MIPI1 DSI D3P TX | Tandaan(1)(2) | 0.5V |
| 2 | GND | Lupa | 0V | |
| 3 | MIPI_DSI_TX1_D3N | LVDS1 o MIPI1 DSI D3N TX | Tandaan(1)(2) | 0.5V |
| 4 | GPIO4_D2_d | GPIO4_D2_d | 3.3V | |
| 5 | MIPI_DSI_TX1_D2P | LVDS1 o MIPI1 DSI D2P TX | Tandaan(1)(2) | 0.5V |
| 6 | MIPI_DSI_TX1_CLKP | LVDS1 o MIPI1 DSI CKP TX | Tandaan(1)(2) | 0.5V |
| 7 | MIPI_DSI_TX1_D2N | LVDS1 o MIPI1 DSI D2N TX | Tandaan(1)(2) | 0.5V |
| 8 | MIPI_DSI_TX1_CLKN | LVDS1 o MIPI1 DSI CKN TX | Tandaan(1)(2) | 0.5V |
| 9 | MIPI_DSI_TX1_D1P | LVDS1 o MIPI1 DSI D1P TX | Tandaan(1)(2) | 0.5V |
| 10 | MIPI_DSI_TX1_D0P | LVDS1 o MIPI1 DSI D0P TX | Tandaan(1)(2) | 0.5V |
| 11 | MIPI_DSI_TX1_D1N | LVDS1 o MIPI1 DSI D1N TX | Tandaan(1)(2) | 0.5V |
| 12 | MIPI_DSI_TX1_D0N | LVDS1 o MIPI1 DSI D0N TX | Tandaan(1)(2) | 0.5V |
| 13 | GND | Lupa | 0V | |
| 14 | PCIE30_RX1P | 0.5V | ||
| 15 | PCIE30_RX0P | 0.5V | ||
| 16 | PCIE30_RX1N | 0.5V | ||
| 17 | PCIE30_RX0N | 0.5V | ||
| 18 | GND | Lupa | 0V | |
| 19 | PCIE30_TX1P | 0.5V | ||
| 20 | PCIE30_TX0P | 0.5V | ||
| 21 | PCIE30_TX1N | 0.5V | ||
| 22 | PCIE30_TX0N | 0.5V | ||
| 23 | GND | Lupa | 0V | |
| 24 | PCIE30_REFCLKP_IN | 0.5V | ||
|
25 |
PCIE30X2_CLKREQN_
M0 |
SATA_CP_POD |
GPIO0_A6_d |
3.3V |
| 26 | PCIE30_REFCLKN_IN | 0.5V | ||
| 27 | VCC_SYS | 3.3-5V Main Power input | 3.4-5V | |
| 28 | GND | Lupa | 0V | |
| 29 | VCC_SYS | 3.3-5V Main Power input | 3.4-5V | |
| 30 | GND | Lupa | 0V | |
| Tandaan:
1. Default na MIPI DSI na output. Ngunit maaaring magbago sa output ng LVDS sa pamamagitan ng software. 2. Maaaring itakda sa Du-LVDS. 3. Hilahin hanggang sa VCC_SYS，Ang pagtatakda ng 0V ay maaaring Power OFF. |
||||
Development Kit
Development Kit (SBC3568)
Gabay sa Pagdisenyo ng Hardware
Sanggunian ng Peripheral Circuit
Panlabas na Kapangyarihan
Pangunahing 5V
PANGUNAHING 3.3V
Debug Circuit
TVI Interface Circuit
TP28x5
VIN 4CH
Bakas ng paa sa PCB
Ang larawan ng mga konektor ng carry board (Pitch 1.27mm)
Mga Katangiang Elektrikal ng Produkto
Pagwawaldas at Temperatura
| Simbolo | Parameter | Min | Typ | Max | Yunit |
|
VCC_SYS |
System IO
Voltage |
3.4V |
5 |
5.5 |
V |
|
Isys_in |
VCC_SYS
input Kasalukuyan |
1400 |
2050 |
mA |
|
| VCC_RTC | RTC Voltage | 1.8 | 3 | 3.4 | V |
|
Iirtc |
RTC input
Kasalukuyan |
5 |
8 |
uA |
|
|
VCC3V3_SYS |
3V3 IO Voltage |
3.3 |
V |
||
|
I3v3_out |
VCC_3V3
kasalukuyang output |
500 |
mA |
||
|
Ta |
Operating Temperatura |
-0 |
70 |
°C |
|
|
Tstg |
Temperatura ng Imbakan |
-40 |
85 |
°C |
Pagiging maaasahan ng Pagsusulit
| Mataas na Temperatura sa Operating Test | ||
| Mga nilalaman | Gumagana ng 8h sa mataas na temperatura | 55 ° C ± 2 ° C |
| Resulta | Pass | |
| Operating Life Test | ||
| Mga nilalaman | Nagpapatakbo sa kwarto | 120h |
| Resulta | Pass | |
Naka-embed na Disenyo ng Boardcon
www.armdesigner.com.
Mga Dokumento / Mga Mapagkukunan
 |
BOARDCON Mini3568 Computer sa Module [pdf] User Manual Mini3568, Mini3568 Computer sa Module, Computer sa Module, Module |
