Tizwis CL-V11 LED Fill Light
Product Information
Specifications
- Product Name: LED Fill Light
- Models: CL-V11, CL-V11SE, CL-V11R
- Ultra-thin design
- Color temperature/brightness adjustable
- Built-in 3000mAh battery
- Approximately 2 hours of continuous lighting
- Compatibility: Mobile phones and laptops
Product Usage Instructions
Matters Needing Attention
- This fill light does not have waterproof and dustproof functions.
- Do not let this fill light be strongly impacted.
- Do not look directly at the light-emitting surface of the fill lamp in use for a long time in a static distance, or it may damage your vision.
- After charging, unplug the power cord.
- After not using this product for a long time, the battery should be fully charged before using this product again, otherwise it may lead to no power and unable to start.
- To extend the service life of the battery, it is recommended to charge and maintain it every three months.
- This product has a built-in rechargeable lithium battery, which has a certain life limit. After a certain period of use, the performance will be reduced, which is a normal phenomenon.
Product Installation
Fixing Clip 1
It is fixed through the 1/4 screw hole and can be fixed by screwing the knob. (Compatible with other accessories linked by 1/4 screw)
Fixing Clip 2
- First install the single leg of the fixing clip into the slot on the back of the fill lamp.
- Then push the fixing clip towards the direction of both feet until the two feet of the fixing clip are also installed in the slot of the fill lamp.
- Screw out the mobile phone mounting base of fixing clip 2.
- Place the mobile phone in the direction as shown in the figure.
Function and Display
- CL-V11
- ON/OFF: Press and hold the power button for 3 seconds to turn on the fill light. Press and hold the power button again for 3 seconds to turn off the light.
- Parameter Settings: Briefly press the M button to toggle color temperature/brightness options. Use the +/- buttons to adjust the parameter values.
- Charge: When using Type-c or Micro-USB interface to charge, the battery indicator will flash in flowing water. When the indicator is no longer flashing, it means that the charging is completed.
- CL-V11SE and CL-V11R
- ON/OFF: Press and hold the power button for 3 seconds to turn on the fill light. Press and hold the power button again for 3 seconds to turn off the light.
- Mode Switching: Briefly press the power button to switch modes, CCT/HSV/special effect, and three modes are switched.
- Parameter Adjustment: In any mode, briefly press the M key to switch between different parameters, and use the +/- keys to adjust the parameter values.
FAQ
- Q: Does the fill light have waterproof and dustproof functions?
A: No, the fill light does not have waterproof and dustproof functions. - Q: How long does the battery last?
A: The built-in 3000mAh battery can provide approximately 2 hours of continuous lighting.
Preface
Thank you for purchasing our products!
This is an ultra-thin fill light, which is compact and convenient to use. This product can be used for fill light in mobile phones and laptops, with a variety of color temperature/brightness adjustable,Built-in 3000mAh battery can provide about 2 hours of continuous lighting.
Please read this manual carefully before use, and keep it for future reference after reading.
Matters needing attention
- This fill light does not have waterproof and dustproof functions.
- Do not let this fill light be strongly impacted.
- Do not look directly at the light-emitting surface of the fill lamp in use for a long time in a static distance, or it may damage your vision.
- After charging, unplug the power cord.
- After not using this product for a long time, the battery should be fully charged before using this product again, otherwise it may lead to no power and unable to start.
- To extend the service life of the battery, it is recommended to charge and maintain it every three months.
- This product has a built-in rechargeable lithium battery, which has a certain life limit. After a certain period of use, the performance will be reduced, which is a normal phenomenon.
Product introduction
- Luminous surface
- Type-c charging port
- Micro-usb charging port
- Value decrease button
- Value increase button
- Power/mode switch
- Retaining clip 1
- Angle adjustment knob
- Indicator/display
- Retaining clip 2
- Fixed knob
- 1/4 screw hole
- Parameter switching
Product installation
Fixing clip 1
It is fixed through 1/4 screw hole and can be fixed by screwing the knob. (Compatible with other accessories linked by 1/4 screw).
Fixing clip 2
- First install the single leg of the fixing clip into the slot on the back of the fill lamp.
- Then push the fixing clip towards the direction of both feet until the two feet of the fixing clip are also installed in the slot of the fill lamp.
- Screw out the mobile phone mounting base of fixing clip 2.
- Place the mobile phone in the direction as shown in the figure.
Function and display
CL-V11
- ON/OFF
Press and hold the power button for 3 seconds, and the fill light will turn on. Press and hold the power button again for 3 seconds to turn off the light. - Parameter settings
Briefly press the “M” button to Toggle color temperature/brightness options. Use the “+”/”-” buttons to adjust the parameter values. - Charge
When using Type-c or Micro-USB interface to charge, the battery indicator will flash in flowing water, When the indicator is no longer flashing, it means that the charging is completed.
CL-V11SE
- ON/OFF
Press and hold the power button for 3 seconds, and the fill light will turn on. The default is white light mode. Press and hold the power button again for 3 seconds to turn off the light. - Mode switching
Briefly press the power button to switch between warm light, cold light and white light. - Brightness adjustment
In any mode, use the “+”/”-” keys to adjust the brightness, which can be adjusted by 10 levels. - Charge
When using Type-c or Micro-USB interface to charge, the battery indicator will flash in flowing water, When the indicator is no longer flashing, it means that the charging is completed.
CL-V11R
- ON/OFF ON/OFF
Press and hold the power button for 3 seconds, and the fill light will turn on. Press and hold the power button again for 3 seconds to turn off the light. - Mode switching
Briefly press the power button to switch modes, CCT/HSV/ special effect, and three modes are switched. - Parameter adjustment
In any mode, briefly press the “M” key to switch between different parameters, and use the “+”/”-” keys to adjust the parameter values - Special effect mode
Support 24 kinds of special effects. - Charge
When using Type-c or Micro-USB interface to charge, the battery indicator will flash in flowing water, When the indicator is no longer flashing, it means that the charging is completed.
Specifications
| Model | CL-V11 | |||
| Colour | 2500 K-9000 K（±200 K） | |||
| Brightness | 0-100% | |||
| LED Qty | 60pcs | |||
| illuminanc e（lux） | 2500 K | 4500 K | 9000 K | |
| distance | 0.3 m | 900 | 1200 | 1000 |
| 0.5 m | 350 | 500 | 400 | |
| CRI | ≥95 | |||
| TLCI | ≥97 | |||
| Battery | 3.7 V 3000mA h（11.1W h） | |||
| Power | 5 W | |||
| Duration | About 1.5 hours | |||
| Input | 5V/1A | |||
| Charging port | Type- C/Micro-usb | |||
| Fixed interface | 1/4 screw hole, retaining clip 1, retaining clip 2 | |||
| Size | 104*75*11.8mm | |||
| Weight | About 140 g | |||
| Accessories | LfiEx iDnlgi gchlti*p11, ,Tfiyxpien-gC cclhi pa r2ging cable*1, | |||
| Model | CL-V11SE | |||
| Colour | 2500 K/4500K/9000 K（±200 K） | |||
| Brightness | 10 levels adjustable | |||
| LED Qty | 60pcs | |||
| illuminanc e（lux） | 2500 K | 4500 K | 9000 K | |
| distance | 0.3 m | 900 | 1200 | 1000 |
| 0.5 m | 350 | 500 | 400 | |
| CRI | ≥95 | |||
| TLCI | ≥97 | |||
| Battery | 3.7 V 3000mA h（11.1W h） | |||
| Power | 5 W | |||
| Duration | About 1.5 hours | |||
| Input | 5V/1A | |||
| Charging port | Type- C/Micro-usb | |||
| Fixed interface | 1/4 screw hole, retaining clip 1, retaining clip 2 | |||
| Size | 104*75*11.8mm | |||
| Weight | About 140 g | |||
| Accessories | LfiEx iDnlgi gchlti*p11, ,Tfiyxpien-gC cclhi pa r2ging cable*1, | |||
| Model | CL-V11R | |||||
| CCT | 2500 K-9000 K（±200 K） | |||||
| Brightness | Brightness adjustment range ：0-100 % | |||||
| LED Qty | RGB:30pcs BI：48pcs | |||||
| illuminance（lux） | Warm light | Cold light | Red | Green | Blue | |
| distance | 0.3 m | 900 | 1000 | 200 | 100 | 400 |
| 0.5 m | 350 | 400 | 80 | 40 | 180 | |
| CRI | ≥95 | |||||
| TLCI | ≥97 | |||||
| RGB（HSV） | 0-35 9（Full color） | |||||
| Special effect | 24 kinds | |||||
| Battery | 3.7 V 3000mA h（11.1W h） | |||||
| Power | 5 W | |||||
| Duration | About 1.5 hours | |||||
| Input | 5V/1A | |||||
| Charging port | Type- C/Micro-usb | |||||
| Fixed interface | 1/4 screw hole, retaining clip 1, retaining clip 2 | |||||
| Size | 104*75*11.8mm | |||||
| Weight | About 140 g | |||||
| Accessories | fiL Ex iDnlgi gchlti*p11, ,Tfiyxpien-gC cclhi pa r2ging cable*1, | |||||
The specifications and parameters of this product are tested by the company’s laboratory samples. The finished product may have some differences ,which will not affect the normal use; if the design and specifications changed will not prior notice.
Documents / Resources
 |
Tizwis CL-V11 LED Fill Light [pdf] User Manual CL-V11, CL-V11SE, CL-V11R, CL-V11 LED Fill Light, LED Fill Light, Fill Light, Light |
