Expansion Module Manuals & User Guides

DNAKE B17-EX001-S Expansion Module User Manual

May 28, 2025

DNAKE B17-EX001-S Expansion Module User Manual REMARK Please follow the user manual for correct installation and testing. If there is any doubt please call our tech-supporting and customer center. Our company applies ourselves to reformation and innovation of our products.…

Brand: DNAKE

logic io EX9043D MODBUS I-O Expansion Module Instruction Manual

May 20, 2025

Technical Manual for RT-EX-9043D Version 2.03 15 x Digital Output Introduction The EX9043D MODBUS I/O Expansion module is a high-quality and low-cost add-on data acquisition device that allows expanding the on-board digital output capabilities on X32-based RTCU units almost indefinitely…

Brand: logic IO

PARADOX PGM4-TI02 4-PGM Expansion Module Instruction Manual

May 8, 2025

PARADOX PGM4-TI02 4-PGM Expansion Module Technical Specifications Power input: Typically 11 to 16 Vdc Number of outputs: 4 form “C” relays rated @ 125V, 5A resistive load Current Consumption: Typical 13mA, 150mA max. (all PGMs active) Humidity: 95% maximum Product…

Brand: Paradox

PARADOX ZX82 8 Zone Input Expansion Module Instruction Manual

May 8, 2025

PARADOX ZX82 8 Zone Input Expansion Module Specifications: Product Name: ZX82 8-Zone Input Expansion Module Installation Manual Version: V1.20 and higher Compatibility: Works with Paradox panels - EVO, Spectra, or MG Features: 8 zones input expansion, Zone Status LED indicators,Power…

Brand: Paradox

PARADOX ZX8SP 8 Zone Expansion Module User Manual

May 8, 2025

PARADOX ZX8SP 8 Zone Expansion Module Product Information The ZX8SP 8-Zone Expansion Module V5.0 serves as an interface between the control panel and hardwired detection devices. It provides eight additional hardwired inputs and one 50 mA on-board PGM output. Please…

Brand: Paradox

PARADOX RTX3 Wireless Expansion Module Instruction Manual

May 8, 2025

PARADOX RTX3 Wireless Expansion Module Instruction Manual Introduction The RTX3 is a 2-way, 32 zone wireless expansion module which enables EVO and SP Series control panels to support wireless hardware such as sirens, motion detectors, water detectors, and remote controls.…

Brand: Paradox

BOSCH B228 SDI2 8-Input, 2-Output Expansion Module Installation Guide

May 3, 2025

BOSCH B228 SDI2 8-Input, 2-Output Expansion Module Specifications 8 points/zones supervised expansion device 2 additional switched outputs Connects to control panels through the SDI2 bus Communicates back all point status changes to the control panel Inputs and outputs accessed through…

Brand: Bosch

Danfoss AK-XM 204B Expansion Module Instructions

April 16, 2025

REFRIGERATION AND AIR CONDITIONING Instructions AK-XM 204B AK-XM 204B Expansion Module The Product contains electrical components And may not be disposed together with domestic waste. Equipment must be separate collected with Electrical and Electronic waste. According to Local and currently…

Brand: Danfoss

Danfoss Gas Detection Controller Unit and Expansion Module User Guide

April 16, 2025

ENGINEERING TOMORROW User Guide Danfoss Gas Detection Controller unit and Expansion module Intended use The Danfoss gas detection controller unit is controlling one or multiple gas detectors, for monitoring, detection and warning of toxic and flammable gases and vapours in…

Brand: Danfoss

Danfoss DHP-R Expansion Module Installation Guide

April 15, 2025

DHP-R InstallatIon InstRuctIons ExPansIon moDulE, HPc Em coolIng moDulE, HPc cm VMBQI202 Important information! 24 VAC 1 must not be connected together with: 24VAC 2 24V0C Other equipment that uses 0-10V control signal Signal ground GND 24 VAC 2 must…

Brand: Danfoss