IN2 ACCESS CP-6638 Gilbert Wireless Loop Kit

Mwongozo wa maagizo ya Gilbert Wireless Loop Kit

Mfumo huo unajumuisha detector ya magnetic na mpokeaji. Innovation yake kuu iko katika mawasiliano ya wireless ya detector magnetic na mpokeaji ambayo inawezesha sana ufungaji. Iliyoundwa kwa ajili ya kuunganishwa kwa ufanisi, emitter imewekwa kwa urahisi chini, kuhakikisha uendeshaji wa kuaminika na salama. Mpokeaji ana matokeo 2 ya relay kwa utendakazi wa utambuzi wa msukumo na usalama (uwepo wa gari).

 Maagizo ya Usalama

• Wakati wa majibu chini ya 60ms
• Kifaa chenye Ugavi wa Nishati wa SELV/PELV

Vituo vya Kisambazaji na Kipokeaji

Ufungaji wa kawaida - lango la kuteleza

Ufungaji wa kawaida - Kizuizi

Viunganisho vya Pato la Mpokeaji

*Powered and safe system configuration

Kiashiria kinachoongozwa na Mpokeaji

Kuanzisha

1. Weka betri
2. Connect receiver power supply
3. Check option selectors
4. Carry out programming process (Point 7)
5. Install detector on gate/barrier
6. Ensure minimum distance of 1m
7. Install and wire receiver
8. Washa usambazaji wa umeme
9. Carry out calibration process (Point 8)
10. Test system on gate/barrier

Kumbuka: The kit is supplied with the transmitter and receiver pre-programmed as standard (skip 7 if single TX installed).

Mchakato wa Kupanga Programu

Upangaji wa mwongozo wa kisambazaji (hadi jumla ya vigunduzi 7 kwa kila kipokeaji)

Kuweka upya kumbukumbu (kufuta vigunduzi vilivyopangwa)

Mchakato wa Kurekebisha (Utatekelezwa Wakati Kigunduzi Kimewekwa Katika Nafasi)

* Katika kipindi hiki cha 120sec, visambazaji data vilivyooanishwa na kipokeaji rekebisha ili kutambua walicho nacho katika mazingira yao, na kuchukua vigezo hivi kama thamani ya awali.

Kiashiria Kamili cha Kumbukumbu
Milio kadhaa kwa sekunde 10 unapojaribu kukariri kisambaza data kipya. Mfumo unaweza kuhifadhi transmita 7 kwa kila chaneli.

Kiashiria cha Betri ya Chini
Milio 4 kila mara ujumbe unapopokelewa kutoka kwa kisambaza data kilichopangwa. Zote mbili, LED ya onyo na buzzer huwashwa kwa wakati mmoja.

Mipangilio ya Chaguo la Mpokeaji

Nchi za Ugunduzi

When a vehicle is first detected, both outputs are triggered. Shortly after the impulse output switches off until the sensor is full clear and another vehicle is detected. The presence output remains on as long as the vehicle is detected by the sensor. Once the vehicle has cleared the sensor, the presence output switches off. (NOTE: DIP 5 (ON) on the receiver enables a
5 sec switch off delay) If multiple detectors are used, the impulse output will switch every time the sensor is activated and deactivated but the presence remains switched as long as one sensor is covered.

Vigezo vya Kigunduzi

Juu ya ardhi / mlima wa uso

Chini ya ardhi / iliyoingia

Vipimo vya Kiufundi

Vipimo	Maelezo
Receiver Supply Voltage	12/24 AC/DC
Betri	2 x AA 3.6V lithium battery
Maisha ya Betri	miaka 4
Kumbukumbu ya Mpokeaji	7 transmitter per receiver
Matokeo ya Mpokeaji	2 Relays, Voltagna mawasiliano ya bure
Receiver Power Consumption	0.5 W – 12 V / 1.2 W – 24 V
Masafa	50m
Joto la Kufanya kazi	-35°C hadi +55°C
Programu	Darasa A
Rated Transient Overvoltage	330V
Transmitter Power Consumption	Transmitting 17mA / Stand by 100uA
Wakati wa Majibu	Chini ya 60 ms

Vidokezo vya Ufungaji

• Installation, start-up, modification, and retrofitting of the system may only be carried out by a qualified person.
• Zima ujazo wa uendeshajitage kabla ya kufanya kazi kwenye mfumo.
• The system doesn’t have fuse protection. It is recommended to include exterior protection minimum 100mA and maximum 250mA.
• If there is any doubt, it is advisable to perform a complete memory wipe (process 7).

Mfumo wa Kugundua Gari isiyo na waya ya Gilbert

Mwongozo wa kuanza haraka
Mwongozo huu umeundwa ili kukusaidia kusanidi na kuanza kutumia mfumo wako wa kutambua pasiwaya kwa urahisi. Iwe unasakinisha vitambuzi katika eneo la maegesho ya magari, barabara kuu, au eneo la biashara, Gilbert hutoa utambuzi wa gari unaotegemewa na katika wakati halisi bila kuhitaji waya nyingi. Fuata hatua zilizoainishwa hapa chini ili kufanya mfumo wako ufanye kazi kwa haraka, ukihakikisha utendakazi bora na usahihi tangu mwanzo.

Vipengele muhimu

 

Juu ya kitanzi cha wireless cha ardhi

1. Hatua ya 1: Carefully mark the hole positions on the ground using the mounting base or template as a guide. Ensure correct alignment and that the wireless loop is level before continuing. Use an appropriate drill and bit suitable for the surface material to drill holes at the marked positions.
2. Hatua ya 2: Position the wireless loop over the drilled holes, ensuring correct alignment. Insert the provided bolts through the holes in the base of the wireless loop and into the drilled holes in the ground. Using a suitable tool, tighten the bolts securely to ensure the detector is firmly anchored in place.
3. Hatua ya 3: Mara tu betri za AA zimewekwa (zinazotolewa na kitengo), funga tena kifuniko kwa usalama, uhakikishe kuwa imefungwa vizuri ili kulinda dhidi ya vumbi na unyevu. Kitengo kikiwa kimekusanyika kikamilifu, endelea kutekeleza utaratibu wa urekebishaji kama ilivyoainishwa katika mwongozo wa maagizo. Hatua hii ni muhimu ili kuhakikisha utambuzi sahihi wa gari na utendakazi bora.

Vipengele muhimu

In-ground Wireless Loop

1. Hatua ya 1: Using a core drill, carefully cut a hole in the ground’s surface to accommodate the in-ground wireless loop. Ensure the hole is sized correctly, allowing enough space for the wireless loop to sit flush with the surface.
2. Hatua ya 2: Weka alama kwenye sehemu za shimo kwa kutumia msingi wa kupachika kama mwongozo, hakikisha upatanisho sahihi na kwamba kitanzi kisichotumia waya kiko sawa. Chimba mashimo ardhini kwenye sehemu zilizowekwa alama. Ingiza bolts zinazotolewa kupitia msingi na ndani ya mashimo yaliyopigwa. Kwa kutumia chombo kinachofaa, kaza bolts kwa usalama ili kuimarisha kitengo. Hakikisha vipengele vya kuziba vilivyotolewa vinatumika kudumisha ulinzi wa hali ya hewa.
3. Hatua ya 3: Mara tu betri za AA zimewekwa (zinazotolewa na kitengo), funga tena kifuniko kwa usalama, uhakikishe kuwa imefungwa vizuri ili kulinda dhidi ya vumbi na unyevu.
4. Hatua ya 4: Kitengo kikiwa kimekusanyika kikamilifu, endelea kutekeleza utaratibu wa urekebishaji kama ilivyoainishwa katika mwongozo wa maagizo. Hatua hii ni muhimu ili kuhakikisha utambuzi sahihi wa gari na utendakazi bora.
5. Hatua ya 5: Jaza tena mapengo yoyote karibu na kitanzi kisichotumia waya kwa nyenzo inayofaa ili kuhakikisha uthabiti na kuzuia maji kuingia kwa usakinishaji wa bomba na salama.

Gilbert Juu-Ground

• Gilbert Above-Ground (component): CP-6647
• Gilbert Above-Ground (Kit): CP-6639
• Mpokeaji: CP-RX GILBERT

Gilbert In-Ground

• Gilbert In-Ground (component): CP-6646
• Gilbert In-Ground (Kit): CP-6638
• Mpokeaji: CP-RX GILBERT

IN2 Access & Control Ltd. Unit 6A Mile Oak, Maesbury Road Industrial Estate, Oswestry, Shropshire, SY10 8GA, UK.

• Web: www.in2access.co.uk
• Barua pepe: technical@in2access.co.uk
• Jumatatu to Friday 08:30 – 17:00

Maswali Yanayoulizwa Mara Kwa Mara

Ni nini dalili ya betri ya chini katika transmita?

When a message is received from a programmed transmitter, there will be 4 beeps, and both the warning LED and buzzer will be activated simultaneously.

Ni visambazaji vingapi vinaweza kuhifadhiwa kwa kila chaneli?

The system can store up to 7 transmitters per channel for efficient operation.

Nyaraka / Rasilimali

IN2 ACCESS CP-6638 Gilbert Wireless Loop Kit [pdf] Mwongozo wa Maelekezo CP-6638 Gilbert Wireless Loop Kit, CP-6638, Gilbert Wireless Loop Kit, Wireless Loop Kit, Loop Kit

Marejeleo

• Mwongozo wa Mtumiaji