IN2 ACCESS CP-6638 Gilbert Wireless Loop Kit
Instruction manual Gilbert Wireless Loop Kit
The system is composed of a magnetic detector and a receiver. Its main innovation lies in the wireless communication of the magnetic detector and the receiver which greatly facilitates installation. Designed for efficient integration, the emitter is easily installed on the ground, ensuring reliable and safe operation. The receiver has 2 relay outputs for the functionalities of impulse detection and security (vehicle presence).
د خوندیتوب لارښوونې
- Reaction time < 60ms
- Device with SELV/PELV Power Supply
Transmitter And Receiver Terminals
Typical Installation – Sliding gate
Typical Installation – Barrier
Receiver Output Connections
*Powered and safe system configuration
Receiver Led Indicator
پیلول
- بیټرۍ داخل کړئ
- Connect receiver power supply
- Check option selectors
- Carry out programming process (Point 7)
- Install detector on gate/barrier
- Ensure minimum distance of 1m
- Install and wire receiver
- د بریښنا رسولو فعال کړئ
- Carry out calibration process (Point 8)
- Test system on gate/barrier
یادونه: The kit is supplied with the transmitter and receiver pre-programmed as standard (skip 7 if single TX installed).
د پروګرام کولو پروسه
Manual programming of transmitter (up to a total of 7 detectors per receiver)
Memory reset (clearing programmed detectors)
Calibration Process (To Be Carried Out When Detector Fixed Into Position)
* During these 120sec, the transmitters paired with the receiver readjust to the detection they have in their environment, taking these parameters as the initial value.
د حافظې بشپړ شاخص
Several beeps for 10 seconds when trying to memorize a new transmitter. The system can store 7 transmitters per channel.
د ټیټ بیټرۍ شاخص
4 beeps each time a message is received from a programmed transmitter. Both, warning LED and buzzer are activated simultaneously.
Receiver Option Settings
Detection States
When a vehicle is first detected, both outputs are triggered. Shortly after the impulse output switches off until the sensor is full clear and another vehicle is detected. The presence output remains on as long as the vehicle is detected by the sensor. Once the vehicle has cleared the sensor, the presence output switches off. (NOTE: DIP 5 (ON) on the receiver enables a
5 sec switch off delay) If multiple detectors are used, the impulse output will switch every time the sensor is activated and deactivated but the presence remains switched as long as one sensor is covered.
Detector Variants
Above ground/ surface mount
Below ground/ embedded
تخنیکي مشخصات
| مشخصات | جزیات |
|---|---|
| Receiver Supply Voltage | 12/24 AC/DC |
| بیټرۍ | 2 x AA 3.6V lithium battery |
| د بیټرۍ ژوند | ۵ کاله |
| د ترلاسه کونکي حافظه | 7 transmitter per receiver |
| د رسیدونکي محصول | 2 Relays, Voltagد وړیا اړیکه |
| Receiver Power Consumption | 0.5 W – 12 V / 1.2 W – 24 V |
| رینج | 50m |
| د کار د حرارت درجه | -35 درجې تر +55 درجو پورې |
| سافټویر | ټولګي الف |
| Rated Transient Overvoltage | 330V |
| Transmitter Power Consumption | Transmitting 17mA / Stand by 100uA |
| د غبرګون وخت | له 60 ms څخه لږ |
د نصب یادښتونه
- Installation, start-up, modification, and retrofitting of the system may only be carried out by a qualified person.
- عملیاتي حجم بند کړئtage before working on the system.
- The system doesn’t have fuse protection. It is recommended to include exterior protection minimum 100mA and maximum 250mA.
- If there is any doubt, it is advisable to perform a complete memory wipe (process 7).
Gilbert Wireless Vehicle Detection System
د چټک پیل لارښود
This guide is designed to help you set up and begin using your wireless detection system with ease. Whether you’re installing the sensors in a car park, driveway, or commercial area, Gilbert delivers reliable, real-time vehicle detection without the need for extensive wiring. Follow the steps outlined below to get your system up and running quickly, ensuring optimal performance and accuracy from the outset.
کلیدي ځانګړتیاوې
Above ground wireless loop
- لومړی ګام: Carefully mark the hole positions on the ground using the mounting base or template as a guide. Ensure correct alignment and that the wireless loop is level before continuing. Use an appropriate drill and bit suitable for the surface material to drill holes at the marked positions.
- لومړی ګام: Position the wireless loop over the drilled holes, ensuring correct alignment. Insert the provided bolts through the holes in the base of the wireless loop and into the drilled holes in the ground. Using a suitable tool, tighten the bolts securely to ensure the detector is firmly anchored in place.
- لومړی ګام: Once the AA batteries have been installed (supplied with unit), securely reattach the lid, ensuring it is properly sealed to protect against dust and moisture. With the unit fully assembled, proceed to run the calibration procedure as outlined in the instruction manual. This step is essential to ensure accurate vehicle detection and optimal performance.
کلیدي ځانګړتیاوې
In-ground Wireless Loop
- لومړی ګام: Using a core drill, carefully cut a hole in the ground’s surface to accommodate the in-ground wireless loop. Ensure the hole is sized correctly, allowing enough space for the wireless loop to sit flush with the surface.
- لومړی ګام: Mark the hole positions using the mounting base as a guide, ensuring correct alignment and that the wireless loop is level. Drill holes into the ground at the marked points. Insert the provided bolts through the base and into the drilled holes. Using a suitable tool, tighten the bolts securely to anchor the unit. Ensure sealing components provided are used to maintain weather protection.
- لومړی ګام: Once the AA batteries have been installed (supplied with unit), securely reattach the lid, ensuring it is properly sealed to protect against dust and moisture.
- لومړی ګام: With the unit fully assembled, proceed to run the calibration procedure as outlined in the instruction manual. This step is essential to ensure accurate vehicle detection and optimal performance.
- لومړی ګام: Backfill any gaps around the wireless loop with a suitable material to ensure stability and prevent water ingress for a flush and secure installation.
Gilbert Above-Ground
- ګیلبرټ Above-Ground (component): CP-6647
- ګیلبرټ Above-Ground (Kit): CP-6639
- اخیستونکی: CP-RX GILBERT
Gilbert In-Ground
- ګیلبرټ In-Ground (component): CP-6646
- Gilbert In-Ground (Kit): CP-6638
- اخیستونکی: CP-RX GILBERT
IN2 Access & Control Ltd. Unit 6A Mile Oak, Maesbury Road Industrial Estate, Oswestry, Shropshire, SY10 8GA, UK
- Web: www.in2access.co.uk
- بریښنالیک: technical@in2access.co.uk
- دوشنبه to Friday 08:30 – 17:00
په مکرر ډول پوښتل شوي پوښتنې
What is the indication for low battery in the transmitter?
When a message is received from a programmed transmitter, there will be 4 beeps, and both the warning LED and buzzer will be activated simultaneously.
How many transmitters can be stored per channel?
The system can store up to 7 transmitters per channel for efficient operation.
اسناد / سرچینې
 |
IN2 ACCESS CP-6638 Gilbert Wireless Loop Kit [pdf] د لارښوونې لارښود CP-6638 Gilbert Wireless Loop Kit, CP-6638, Gilbert Wireless Loop Kit, Wireless Loop Kit, Loop Kit |