CE Electronics CE3871-0 Mwongozo wa Maagizo ya Moduli ya Transceiver ya Powertool

The module’s operation is automated. Attach it to the tool, power it on, and it will establish communication with the tool.
It will attempt to wirelessly connect to the previous controller; if not found, it will scan through available channels to find a new controller.

Maagizo ya Uendeshaji CE3871-0 & CE3871-1

Bunge

The designated cable in the tool should be plugged into the J1 connector.

The J2 connector is used for development and should be left unconnected by the user.
The module must be mounted at least 5mm from the outside edge of the product.

Uendeshaji

Module operation is entirely automated.

Once attached to the tool and powered on, the module will automatically begin communication with the tool and attempt to connect wirelessly to the previous controller.
If the previous controller cannot be found at power-up, the module will automatically scan through the available channels to find a new controller.

Masafa ya Kituo

Kituo	Masafa (GHz)
1	2.410
2	2.415
3	2.420
4	2.425
5	2.430
6	2.435
7	2.440
8	2.445
9	2.450
10	2.455
11	2.460
12	2.465

TAARIFA YA FCC

Taarifa za Udhibiti
Marekani (FCC)
CE3871 Modules comply with Part 15 of the FCC rules and regulations. Compliance with the labeling requirements, FCC notices and antenna usage guidelines is required.
Ili kutimiza Uidhinishaji wa FCC, OEM lazima itii kanuni zifuatazo:

Kiunganishi cha mfumo lazima kihakikishe kuwa maandishi kwenye lebo ya nje yaliyotolewa na kifaa hiki yamewekwa nje ya bidhaa ya mwisho.

Mahitaji ya kuweka lebo ya OEM
ONYO! Kama Mtengenezaji wa Vifaa Halisi (OEM) ni lazima uhakikishe kuwa mahitaji ya uwekaji lebo ya FCC yanatimizwa. Ni lazima ujumuishe lebo inayoonekana kwa uwazi kwenye sehemu ya nje ya ua wa mwisho wa bidhaa ambayo inaonyesha maudhui yafuatayo:
Ina Kitambulisho cha FCC: O4O-CE3871
Kifaa hiki kinatii Sehemu ya 15 ya Sheria za FCC. Operesheni inategemea masharti mawili yafuatayo:

Kifaa hiki hakiwezi kusababisha usumbufu unaodhuru na

Kifaa hiki lazima kikubali uingiliaji wowote uliopokewa, ikiwa ni pamoja na uingiliaji ambao unaweza kusababisha uendeshaji usiohitajika.

Matangazo ya FCC
MUHIMU: CE3871 Modules have been certified by the FCC for use with other products without any further certification (as per FCC section 2.1091). Modifications not expressly approved by C.E. Electronics could void the user’s authority to operate the equipment.
MUHIMU: OEMs must test the final product to comply with unintentional radiators (FCC section 15.107 & 15.109) before declaring compliance of their final product to Part 15 of the FCC Rules.
MUHIMU: The module has been certified for remote, base, and portable radio applications. If the module will be used for portable applications, the device must have a minimum of 5mm separation from the operator.
Kifaa hiki kimejaribiwa na kupatikana kuwa kinatii vikomo vya kifaa cha kidijitali cha Hatari B, kwa mujibu wa Sehemu ya 15 ya Sheria za FCC. Vikomo hivi vimeundwa ili kutoa ulinzi unaofaa dhidi ya kuingiliwa kwa hatari katika usakinishaji wa makazi. Kifaa hiki huzalisha, kutumia na kuangazia nishati ya masafa ya redio na, ikiwa hakijasakinishwa na kutumiwa kwa mujibu wa maagizo, kinaweza kusababisha mwingiliano unaodhuru kwa mawasiliano ya redio. Hata hivyo, hakuna uhakika kwamba kuingiliwa haitatokea katika ufungaji fulani.
Iwapo kifaa hiki kitasababisha usumbufu unaodhuru kwa upokeaji wa redio au televisheni, ambao unaweza kubainishwa kwa kuzima na kuwasha kifaa, mtumiaji anahimizwa kujaribu kusahihisha uingiliaji huo kwa moja au zaidi ya hatua zifuatazo: Elekeza upya au kuhamisha kifaa. kupokea antena, Ongeza utengano kati ya kifaa na kipokezi, Unganisha kifaa na kipokezi kwenye maduka kwenye saketi tofauti, au Wasiliana na muuzaji au fundi mzoefu wa redio/TV kwa usaidizi.

ISED (Uvumbuzi, Sayansi na Maendeleo ya Kiuchumi Kanada)
Kifaa hiki kina visambazaji/vipokezi visivyo na leseni ambavyo vinatii Uvumbuzi, Sayansi na Maendeleo ya Kiuchumi RSS isiyo na leseni ya Kanada. Operesheni inategemea masharti mawili yafuatayo:

Kifaa hiki hakiwezi kusababisha usumbufu.

Kifaa hiki lazima kikubali uingiliaji wowote, ikiwa ni pamoja na kuingiliwa ambayo inaweza kusababisha uendeshaji usiohitajika wa kifaa.

Mahitaji ya kuweka lebo

Labeling requirements for Industry Canada are similar to those of the FCC. A clearly visible label on the outside of the final product enclosure must display the following text:
Ina Model Powertool Transceiver Moduli CE3871, IC: 8507A-CE3871

The integrator is responsible for its product to comply with IC ICES-003 & FCC Part 15, Sub. B – Unintentional Radiators. ICES-003 is the same as FCC Part 15 Sub. B and Industry Canada accept FCC test report or CISPR 22 test report for compliance with ICES-003.
Marekebisho ambayo hayajaidhinishwa waziwazi na CE Electronics yanaweza kubatilisha mamlaka ya mtumiaji kuendesha kifaa.

Firmware Version Identification number (FVIN)

CE3871 firmware versions are 5.x or 6.x. FVIN is displayed on the controller with which the module is communicating.

WASILIANA NA

CE Electronics, Inc.
2107 Hifadhi ya Viwanda
Bryan, OH 43506
Simu: 419-636-6705
Faksi: 419-636-2516

Maswali Yanayoulizwa Mara kwa Mara

Swali: Nitajuaje ikiwa moduli imeunganishwa kwa kidhibiti?

A: The module will automatically establish a connection with the controller when powered on. You can check for successful connection indicators on the tool or controller interface.

Swali: Je, ninaweza kutumia kiunganishi cha J2 kwa madhumuni yoyote?

A: The J2 connector is intended for development purposes only and should not be connected during normal operation to avoid interference with the module's functionality.

Nyaraka / Rasilimali

CE Electronics CE3871-0 Powertool Transceiver Moduli [pdf] Mwongozo wa Maelekezo
CE3871-0, CE3871-1, CE3871-0 Moduli ya Transceiver ya Powertool, CE3871-0, Moduli ya Transceiver ya Powertool, Moduli ya Transceiver, Moduli

Marejeleo

Mwongozo wa Mtumiaji

C E Electronics CE3871-0 Powertool Transceiver Module

Vipimo

Maagizo ya Matumizi ya Bidhaa