BridgeCom SYSTEMS Using Remote Shutdown and Reboot Commands User Guide

Using Remote Shutdown and Reboot Commands

Specifikationer

• Product: SkyBridge Max
• Connectivity: Ethernet cable or WiFi
• Remote Commands: Shutdown and Reboot

Produktanvändningsinstruktioner

Konfiguration

1. Power on your hotspot and wait for it to boot. Ensure network
   connectivity via Ethernet cable or WiFi.
2. From a computer or smartphone on the same network:
   • Öppna a web browser and enter the IP address displayed on the
     SkyBridge Max.
   • Access the WPSD dashboard by clicking Admin in the upper-right
     corner, then Advanced.
   • Navigate to Full Editors -> RF Remote Commands.
   • Ändra inställningar:
     • enabled=true
     • callsign=Your Callsign
     • In the dmr field, remove the ‘#’ at the beginning of reboot and
       shutdown lines.
   • Klicka på Verkställ ändringar.

Hur man använder

1. If using BridgeCom’s codeplugs:
   • In the Remote zone, use the channel knob to select SKY Shutdown
     or SKY Reboot.
2. If not using BridgeCom’s codeplugs:
   • Add talkgroups 9999996 (shutdown) and 9999997 (reboot) with
     corresponding hotspot settings to a channel.
3. If shutdown command was successful, wait 60 seconds before
   removing power. If reboot command was used, wait for unit to boot
   upp.

FAQ

Q: What should I do if the remote commands do not work?

A: Check network connectivity and ensure correct configuration
settings. Try restarting the SkyBridge Max and reapplying the
förändringar.

Using Remote Shutdown and Reboot Commands with your SkyBridge Max
Introduktion
When powering down the SkyBridge Max, it is essential to shut it down properly to avoid the risk of file corruption. Thanks to the intuitive web interface, this is a simple process. However, there are situations where it would be more convenient to remotely shut down the unit without needing to log into its web interface. With a SkyBridge Max, it is possible to configure this functionality using a DMR radio. Configuring additional digital modes and commands is also supported, but the scope of this document is limited to shutdown and reboot commands with a DMR radio.
Konfiguration
1. Power on your hotspot and wait for it to boot. This guide assumes that you are using a SkyBridge Max and are either using an Ethernet cable for network connectivity, or have already configured WiFi.
2. Using a computer (or smartphone) connected to the same network, open a web browser and type in the IP address that appears on the SkyBridge Max display.
You should be directed to your WPSD dashboard page. 3. Click Admin in the upper-right corner
4. Klicka på Avancerat

5. Navigate to Full Editors->RF Remote Commands
6. Change the following lines: a. enabled=true b. callsign=Your Callsign c. Under the dmr field, remove the `#’ at the beginning of the reboot and shutdown lines i. Be sure there is not a `#’ character present at the beginning of the enabled, callsign, reboot, and shutdown lines d. The resulting file should resemble the image below
Click the Apply Changes button when finished.
Hur man använder
1. If using one of BridgeCom’s codeplugs, navigate to the Remote zone and rotate the channel knob to select either SKY Shutdown or SKY Reboot depending on the desired operation to run.

a. If not using one of BridgeCom’s codeplugs, you will need to add talkgroups 9999996 (shutdown) and 9999997 (reboot), and add a channel corresponding to your hotspot’s frequency, color code, and timeslot for each. Guidance on codeplug construction is outside the scope of this article.
2. Be sure the hotspot is not already transmitting, and briefly press the PTT. Immediately after transmitting, your callsign and the talkgroup number should appear on the display. a. Within 30 seconds, the display text should change to Stopped and the line below it should change to MMDVM Inactive b. If this does not occur, it is likely the unit did not shut down or reboot (depending on the operation that was run). In this case, review the steps in the previous section and ensure the PiStar Remote configuration file is correct and saved with the changes that were made.
3. If Step 2 was successful, and the shutdown command was run, wait 60 seconds. It is now safe to remove power from the unit. a. If the reboot command was run, do not remove power from the unit. It should boot and be running again within a few minutes.

Dokument/resurser

BridgeCom SYSTEMS Using Remote Shutdown and Reboot Commands [pdf] Användarhandbok Using Remote Shutdown and Reboot Commands, Remote Shutdown and Reboot Commands, Reboot Commands

Referenser

• Användarmanual