BridgeCom SYSTEMS Brug af fjernnedluknings- og genstartskommandoer

Specifikationer

• Produkt: SkyBridge Max
• Forbindelse: Ethernet-kabel eller WiFi
• Fjernkommandoer: Nedlukning og genstart

Indledning

Når du slukker for SkyBridge Max, er det vigtigt at slukke den korrekt for at undgå risiko for file korruption. Takket være den intuitive web brugerfladen, dette er en simpel proces. Der er dog situationer, hvor det ville være mere bekvemt at lukke enheden ned eksternt uden at skulle logge ind på dens web Med en SkyBridge Max er det muligt at konfigurere denne funktionalitet ved hjælp af en DMR-radio. Konfiguration af yderligere digitale tilstande og kommandoer understøttes også, men omfanget af dette dokument er begrænset til nedluknings- og genstartskommandoer med en DMR-radio.

Konfiguration

1. Power on your hotspot and wait for it to boot. This guide assumes that you are using a SkyBridge Max and are either using an Ethernet cable for network connectivity, or have already configured WiFi.
2. Using a computer (or smartphone) connected to the same network, open a web browser and type in the IP address that appears on the SkyBridge Max display. You should be directed to your WPSD dashboard page.
3. Klik Admin i øverste højre hjørne.
4. Klik Fremskreden.
5. Naviger til Full Editors->RF Remote Commands.
6. Change the following lines:
   • enabled=true
   • callsign=Your Callsign
   • Under the dmr field, remove the # at the beginning of the reboot and shutdown lines.
     • Be sure there is not a # character present at the beginning of the enabled, callsign, reboot, and shutdown lines.
   • Det resulterende file should resemble the image below.

Klik på Anvend ændringer knappen, når du er færdig.

Sådan bruges

1. If using one of BridgeCom’s codeplugs, navigate to the Remote zone and rotate the channel knob to select either SKY Shutdown or SKY Reboot depending on the desired operation to run.
   • If not using one of BridgeCom’s codeplugs, you will need to add talkgroups 9999996 (shutdown) and 9999997 (reboot), and add a channel corresponding to your hotspot’s frequency, color code, and timeslot for each. Guidance on codeplug construction is outside the scope of this article.
2. Be sure the hotspot is not already transmitting, and briefly press the PTT. Immediately after transmitting, your callsign and the talkgroup number should appear on the display.
   • Within 30 seconds, the display text should change to Stoppet and the line below it should change to MMDVM Inactive.
   • If this does not occur, it is likely the unit did not shut down or reboot (depending on the operation that was run). In this case, review trinene i det foregående afsnit og sørg for, at PiStar Remote er konfigureret file er korrekt og gemt med de foretagne ændringer.
3. If Step 2 was successful, and the shutdown command was run, wait 60 seconds. It is now safe to remove power from the unit.
   • If the reboot command was run, do not remove power from the unit. It should boot and be running again within a few minutes.

FAQ

What should I do if the remote commands do not work?

Check network connectivity and ensure correct configuration settings. Try restarting the SkyBridge Max and reapplying thechanges.

Dokumenter/ressourcer

BridgeCom SYSTEMS Brug af fjernnedluknings- og genstartskommandoer [pdfBrugervejledning Brug af fjernnedluknings- og genstartskommandoer, fjernnedluknings- og genstartskommandoer, genstartskommandoer

Referencer

• Brugermanual