BridgeCom SYSTEMS Siv cov chaw taws teeb kaw thiab reboot lus txib

Specifications

• Khoom siv: SkyBridge Max
• Kev sib txuas: Ethernet cable lossis WiFi
• Tej thaj chaw deb commands: shutdown thiab reboot

Taw qhia

Thaum fais fab tuag rau SkyBridge Max, nws yog ib qho tseem ceeb uas yuav tsum kaw nws kom zoo kom tsis txhob muaj kev pheej hmoo file kev noj nyiaj txiag. Ua tsaug rau qhov intuitive web interface, qhov no yog cov txheej txheem yooj yim. Txawm li cas los xij, muaj cov xwm txheej uas nws yuav yooj yim dua rau kev kaw lub tsev tsis tas yuav nkag mus rau hauv nws web interface. Nrog SkyBridge Max, nws tuaj yeem teeb tsa qhov kev ua haujlwm no siv lub xov tooj cua DMR. Configuring ntxiv cov qauv thiab cov lus txib kuj tau txais kev txhawb nqa, tab sis cov peev txheej ntawm cov ntaub ntawv no txwv rau kev kaw thiab rov pib dua cov lus txib nrog DMR xov tooj cua.

Kev teeb tsa

1. Power on your hotspot and wait for it to boot. This guide assumes that you are using a SkyBridge Max and are either using an Ethernet cable for network connectivity, or have already configured WiFi.
2. Using a computer (or smartphone) connected to the same network, open a web browser and type in the IP address that appears on the SkyBridge Max display. You should be directed to your WPSD dashboard page.
3. Nyem Admin nyob rau hauv lub kaum sab xis saum toj.
4. Nyem Advanced.
5. Nkag mus rau Full Editors->RF Remote Commands.
6. Change the following lines:
   • enabled=true
   • callsign=Your Callsign
   • Under the dmr field, remove the # at the beginning of the reboot and shutdown lines.
     • Be sure there is not a # character present at the beginning of the enabled, callsign, reboot, and shutdown lines.
   • Qhov tshwm sim file should resemble the image below.

Nyem qhov Thov Hloov khawm thaum ua tiav.

Yuav siv li cas

1. If using one of BridgeCom’s codeplugs, navigate to the Remote zone and rotate the channel knob to select either SKY Shutdown or SKY Reboot depending on the desired operation to run.
   • If not using one of BridgeCom’s codeplugs, you will need to add talkgroups 9999996 (shutdown) and 9999997 (reboot), and add a channel corresponding to your hotspot’s frequency, color code, and timeslot for each. Guidance on codeplug construction is outside the scope of this article.
2. Be sure the hotspot is not already transmitting, and briefly press the PTT. Immediately after transmitting, your callsign and the talkgroup number should appear on the display.
   • Within 30 seconds, the display text should change to Nres and the line below it should change to MMDVM Inactive.
   • If this does not occur, it is likely the unit did not shut down or reboot (depending on the operation that was run). In this case, review cov kauj ruam hauv ntu dhau los thiab xyuas kom meej PiStar Remote configuration file yog qhov tseeb thiab tau txais kev cawmdim nrog cov kev hloov pauv uas tau ua.
3. If Step 2 was successful, and the shutdown command was run, wait 60 seconds. It is now safe to remove power from the unit.
   • If the reboot command was run, do not remove power from the unit. It should boot and be running again within a few minutes.

FAQ

What should I do if the remote commands do not work?

Check network connectivity and ensure correct configuration settings. Try restarting the SkyBridge Max and reapplying thechanges.

Cov ntaub ntawv / Cov ntaub ntawv

BridgeCom SYSTEMS Siv cov chaw taws teeb kaw thiab reboot lus txib [ua pdf] Cov neeg siv phau ntawv qhia Siv tej thaj chaw deb shutdown thiab reboot commands, tej thaj chaw deb shutdown thiab reboot commands, reboot commands

Cov ntaub ntawv

• Cov neeg siv phau ntawv