Pitunjuk Gancang
AQG-10087-05
FlexNet CommandLink II

FlexNet CommandLink II Wireless Interface

The CommandLink® II wireless interface provides access to a complete suite of functional controls within a gas, water, or electric SmartPoint® transceiver. This Bluetooth® enabled device, coupled with a handheld, can perform activations, deactivation, meter read, on-demand reads, and audits of the SmartPoint module.

Awas: Risk of hot surface. Do not hold the device longer than one (1) minute when operating in an ambient temperature above 40°C (104°F).

Lengkah 1: Ngecas CommandLink II
You must charge the CommandLink II completely before first use.

1. Plug the charging adapter into a power outlet and connect to the Charging Port located next to the Mag Loop on top of the Command Link II.
   Catetan: Make sure you have rechargeable batteries installed before using a power outlet.
   Unit nu boga batré non-rechargeable teu kudu plugged kana stop kontak listrik pikeun ngecas.
2. Indikator LED beureum hurung, nunjukkeun unit nuju ngecas.
3. Unplug the unit when the red LED is no longer illuminated, indicating the CommandLink II is fully charged.
   Catetan: To power down the CommandLink II immediately, press and hold the power button located on the side of the CommandLink II until the PWR LED turns off.

Lengkah 2: Hurungkeun Patalina Komando II

1. Pencét tombol daya.
2. Lampu LED héjo hurung nalika CommandLink II suksés didamel.

Lengkah 3: Jieun Partnership Bluetooth
To use the CommandLink II, you must first establish a Bluetooth partnership with a Windows Mobile, Android, or iOS-equipped handheld device (HHD) or PC.

Eusi pakét

• FlexNet CommandLink II
• Tali Bungee (2)
• Adaptor ngecas (AC/DC)
• Adaptor Ngecas Kandaraan (DC/DC)
• Kasus

LED	Katerangan
CHG (Red)	Ngecas
LNK (Blue)	Bluetooth disambungkeun
PWR (Héjo)	Solid: power on Flash: needs charge/poor battery connection/defective battery

Upami nganggo Alat Panangan Windows Mobile:

1. Pilih Mimitian, teras Setélan.
2. Select Connections, then select Bluetooth COM.
   Power on the CommandLink II if it is off.
3. Pilih Discover Devices.
   A list of all the Bluetooth-enabled devices in range is generated and displayed.
   If your CommandLink II does not appear in the list, make sure that it is powered on. If it is powered on, power cycle it and select Discover Devices again, and repeat this step.
4. Pilih anjeun
   CommandLink II from the list and select Connect.
5. If you are prompted toSet the Bluetooth PIN, enter 0000 and select OK.
6. Pilih OK pikeun kaluar.
7. Pilih X di pojok katuhu handap pikeun kaluar.
8. Pilih FieldLogic Tools tina menu Start.
9. From the FieldLogic Tools main screen, select Menu, and select Options.
10. Pilih tab FlexNet tur pilih CommandLink tina daptar dropdown tipe Alat. Ulah milih CLxxxxxxxxx_BLE.
11. Pilih Meunangkeun Status. FieldLogic Tools nyambung sareng CommandLink II sareng nampilkeun pesen suksés.
12. Pilih OK.
13. Pilih OK deui pikeun mulang ka layar Sambungkeun.

Upami nganggo Alat Android:

1. Pilih ikon Setélan.
2. Select Options, then select FlexNet. FieldLogic displays a list of available devices.
3. Pilih + ka view layar papasangan sistem.AQG – 10007 – 05
4. Pilih CommandLink II (CLxxxxxxxx) anjeun tina daptar alat Bluetooth anu sayogi.
5. Pilih Pair. CommandLink II anjeun teras dipidangkeun dina daptar Alat Dipasangkeun.
6. Balik deui ka Alat FieldLogic.
7. Select the newly-paired CommandLink II in the list and select the information symbol.FieldLogic nyambung ka CommandLink II tur mintonkeun pesen suksés.
8. Pilih Tutup.
9. Pilih panah tukang pikeun mulang ka layar utama FieldLogic.

Upami nganggo Alat Dicekel Ios:

1. Pilih ikon Setélan.
2. Pilih Pilihan, teras pilih FlexNet. FieldLogic nyeken alat teras nampilkeun alat anu sayogi. Daptar refreshes otomatis.
3. Jandéla pop-up idin dipintonkeun. Pilih OK.
4. Pilih CommandLink II (CLxxxxxxxx) anjeun tina daptar alat Bluetooth anu sayogi.
   
5. Select your CommandLink II and then select the information symbol.
6. FieldLogic nyambung ka CommandLink II tur mintonkeun pesen suksés.
7. Pilih Tutup pikeun mulang ka layar Pilihan.
8. Pilih panah tukang pikeun mulang ka layar utama FieldLogic.

Upami nganggo PC:

1. Hurungkeun CommandLink II.
2. Pilih ikon Bluetooth dina desktop komputer Anjeun atawa tina menu Start.
3. Tina panel Alat Bluetooth, pilih Tambah alat.
4. Komputer anjeun milarian alat pikeun nambihan.
5. Select the icon containing the CommandLink II ID number (CLxxxxxxxx).
   Catetan: If two numbers appear, make sure you select CLxxxxxxxx. Do not select CLxxxxxxxx_BLE.
6. Pilih Salajengna.
7. Your computer confirms the successful addition of the CommandLink II.
8. Pilih Tutup pikeun neruskeun.
9. Mimitian FieldLogic Pakakas. Tina layar utama, pilih Alat sareng pilih Pilihan.
10. Pilih expander Setélan FlexNet tur pilih CommandLink tina daptar turun-handap Alat Komunikasi. Pilih alat Anjeun tina daptar turun-handap Ngaran alat.
11. Select Get Status.
    FieldLogic Tools connects with the CommandLink II and displays a success message.
12. Pilih OK pikeun mulang ka layar Pilihan.
13. Pilih OK pikeun mulang ka layar Sambungkeun.

Attach a Strap to the CommandLink II

To attach a strap, slide it in between the slots on the sides of the unit.

AQG – 10007 – 05

Pernyataan minuhan

PERHATOSAN
Any modifications made to this device that are not approved by Sensus may void the authority granted to the user by the FCC to operate equipment.

PERHATOSAN
Pikeun Kelas B - Radiator Teu Dihaja:
This device complies with Part 15 of the FCC Rules. Operation is subjectto the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.

PERHATOSAN
ICES-003 Kelas B Bewara—Avis NMB-003, Kelas B
Aparat digital Kelas B ieu saluyu sareng ICES-003 Kanada.

PERHATOSAN
Catetan: Alat ieu geus diuji sarta kapanggih sasuai jeung wates pikeun alat digital Kelas B, nurutkeun Bagian 15 tina Aturan FCC.
Watesan ieu dirarancang pikeun nyayogikeun panyalindungan anu wajar tina gangguan anu ngabahayakeun dina pamasangan padumukan. Alat ieu ngahasilkeun, ngagunakeun, sareng tiasa mancarkeun énergi frekuensi radio sareng, upami henteu dipasang sareng dianggo saluyu sareng petunjuk, tiasa nyababkeun gangguan anu ngabahayakeun kana komunikasi radio. Nanging, teu aya jaminan yén gangguan moal lumangsung dina pamasangan khusus. Upami alat ieu nyababkeun gangguan anu ngabahayakeun kana panarimaan radio atanapi televisi, anu tiasa dipastikeun ku cara mareuman sareng ngaktipkeun alat, pangguna didorong pikeun nyobian ngabenerkeun gangguan ku salah sahiji atanapi langkung tina ukuran ieu:

• Reorient atawa mindahkeun anteneu panarima
• Ningkatkeun separation antara alat jeung panarima
• Sambungkeun alat-alat kana stop kontak dina sirkuit béda ti nu disambungkeun ka panarima
• Taroskeun ka dealer atanapi teknisi radio/TV anu berpengalaman pikeun pitulung

PERHATOSAN
Alat ieu saluyu sareng standar RSS anu dibebaskeun lisénsi Industri Kanada. Operasi tunduk kana dua kaayaan di handap ieu: (1) alat ieu moal ngabalukarkeun gangguan, jeung (2) alat ieu kudu narima sagala gangguan, kaasup gangguan nu bisa ngabalukarkeun operasi nu teu dihoyongkeun alat.

PERHATOSAN
This radio transmitter, the Sensus CL201, has been approved by Industry Canada to operate with the antenna types listed below, with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.

PERHATOSAN
Dina peraturan Industri Kanada, pamancar radio ieu ngan ukur tiasa beroperasi nganggo anteneu tina jinis sareng kauntungan maksimum (atanapi langkung handap) anu disatujuan pikeun pamancar ku Industri Kanada. Pikeun ngirangan poténsi gangguan radio ka pangguna anu sanés, jinis anteneu sareng kauntunganna kedah dipilih supados kakuatan radiasi isotropik anu sami (eirp) henteu langkung ti anu dipikabutuh pikeun komunikasi anu suksés.

PERHATOSAN
There is a danger of explosion if batteries are mishandled or incorrectly replaced. On systems with replaceable batteries, replace only with the same manufacturer and type or equivalent type recommended per the instructions provided in the product service manual.
Entong ngabongkar batré atanapi nyobian ngecas deui di luar sistem. Ulah miceun batré dina seuneu.
Buang batré anu leres saluyu sareng parentah produsén sareng peraturan lokal.

PERHATOSAN
ULAH INCINERATE atawa nempatkeun sél batré dina suhu leuwih ti 212 ° F. Pangobatan sapertos kitu tiasa nyababkeun beubeulahan sél.

PERHATOSAN
EXPLOSION HAZARD – BATTERIES MUST ONLY BE CHANGED IN AN AREA KNOWN TO BE NON-HAZARDOUS.

xylem.com
SENSUS | 637 Davis Drive | Morrisville, NC 27560 | 800.638.3748 | sénsus.com

©2026 Sensus. All products purchased and services performed are subject to Sensus’ terms of sale, available at either sensus.com/TC atanapi 1-800-638-3748. Sensus reserves the right to modify these terms and conditions in its own discretion without notice to the customer. The Sensus logo is a registered trademark of Sensus.
This document is for informational purposes only, and SENSUS MAKES NO EXPRESS WARRANTIES IN THIS DOCUMENT. FURTHERMORE, THERE ARE NO IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, WARRANTIES AS TO FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY. ANY USE OF THE PRODUCTS THAT IS NOT SPECIFICALLY PERMITTED HEREIN IS PROHIBITED.

Dokumén / Sumberdaya

xylem FlexNet CommandLink II Wireless Interface [pdf] Pituduh pamaké CL201, FlexNet CommandLink II Wireless Interface, FlexNet CommandLink II, Wireless Interface

Rujukan

• Manual pamaké