Weihai Printer Mainboard Module

Specific Operating Conditions

1. This product is a high-performance printer mainboard (Mainboard Module), specifically designed for printer equipment. The module integrates wireless communication functionality (Wi-Fi) and is intended to serve as a core component installed inside the printer, enabling data transmission and device control with a host computer. It supports communication with the host via USB, Ethernet, or Wi-Fi interfaces to receive print data and execute printing tasks.
2.  Professional Use Limitation: This module has professional user condition restrictions. The host product manufacturer must clearly state the warning “This product is intended for professional users only” in the product manual.
3.  Pamasangan sareng Parentah Operasi:
   1. Antenna installation: Remove the nut from the antenna, insert the metal end of the antenna through the mounting hole on the main control board bracket, and then reinstall the nut onto the antenna.
   2. Route the antenna through the designated hole as shown in the diagram and plug it into the main control board.
   3. Mount the main board onto the bracket and secure it using an electric screwdriver to install the following four screws (torque setting: 7 ± 0.5 kgf·cm).
   4. Attach the wireless communication module onto the metal end of the antenna.
   5. Plug the printhead harness connector into the main board, and gently bend the adapter cable at the connection end..
   6. Connect the printhead cable as illustrated.
4. Mainboard Usage Instructions
   After completing the above installation steps, toggle the rocker switch on the mainboard—the printer’s indicator light will illuminate brightly.
   The printer will automatically search for the pre-configured end-customer Wi-Fi SSID and connect to it. End users may also use the printer’s accompanying web-based utility tool to modify the Wi-Fi SSID to which the printer should automatically connect.
   Print jobs are sent to the printer via the Wi-Fi interface, and the printer executes the printing tasks accordingly.
5. Operating temperature: 5-45 ℃

Host Product Integration Labeling Instructions

1.  If the FCC Identifier (FCC ID) cannot be clearly seen after the module is installed inside the equipment, a label indicating the contained module must be affixed to the exterior of the equipment. The label format must follow “Contains FCC ID: 2BTZASRN” , complying with FCC KDB guidance 784748 labeling specifications.
2. End-user equipment must comply with the labeling requirements of §15.19. For special equipment labeling rules, please refer to §2.925, §15.19(a)(5), and related KDB documents; electronic labels must comply with §2.935 requirements.

Additional Test Requirements

Test Mode and Additional Test Requirements

1. The Original Equipment Manufacturer (OEM) integrator must ensure there are no instructions for end-users to manually remove or install this module.
2. This module is limited to installation in mobile applications. All other operating configurations (including portable configurations compliant with §2.1093 and different antenna configurations) require separate approval.
3. The host product manufacturer is ultimately responsible for performing additional compliance testing on the end product after installation of this module, including but not limited to tests related to digital device emissions, PC peripheral requirements, and other transmitters within the host.

Test Mode Software Access: Supports Wifi Test . Test items, frequency, transmit power, modulation type, and other parameters can be selected within the test script instructions.

Produk Host

Host Product Manufacturer FCC Other Parts and Part 15B Compliance Requirements

1. This modular transmitter is only certified for the specific rule parts listed in the FCC grant. The host product manufacturer must ensure the host complies with other applicable FCC rules not covered by the modular transmitter certification.
2. Under all circumstances, the host product manufacturer must ensure that the host product with this module installed and operating complies with Part 15B requirements.
3. If the end product is a Class B or Class A digital device or peripheral, its user manual must prominently include the user notice statement specified in §15.105 or a similar statement:

(I) Class B Device Notice:

Catetan: Alat ieu geus diuji sarta kapanggih sasuai jeung wates pikeun alat digital Kelas B, nurutkeun bagian 15 Aturan FCC. Watesan ieu dirarancang pikeun nyayogikeun panyalindungan anu wajar tina gangguan anu ngabahayakeun dina pamasangan padumukan. Alat ieu ngahasilkeun, ngagunakeun sareng tiasa mancarkeun énergi frekuensi radio sareng, upami henteu dipasang sareng dianggo saluyu sareng petunjuk, tiasa nyababkeun gangguan anu ngabahayakeun kana komunikasi radio. Nanging, teu aya jaminan yén gangguan moal lumangsung dina pamasangan khusus. Upami alat ieu nyababkeun gangguan anu ngabahayakeun kana panarimaan radio atanapi televisi, anu tiasa dipastikeun ku cara mareuman sareng ngaktipkeun alat, pangguna didorong pikeun nyobian ngabenerkeun gangguan ku salah sahiji atanapi langkung tina ukuran ieu:

• Reorient atawa mindahkeun anteneu panarima.
• Ningkatkeun separation antara alat jeung panarima.
• Sambungkeun alat-alat kana stop kontak dina sirkuit béda ti nu disambungkeun ka panarima.
• Taroskeun ka dealer atanapi teknisi radio/TV anu berpengalaman pikeun pitulung.

 Class A Device Notice:

Catetan: Alat ieu geus diuji sarta kapanggih matuh ka wates pikeun alat digital Kelas A, nurutkeun bagian 15 Aturan FCC. Watesan ieu dirarancang pikeun nyayogikeun panyalindungan anu wajar tina gangguan anu ngabahayakeun nalika alat-alat dioperasikeun di lingkungan komérsial. Alat ieu ngahasilkeun, ngagunakeun, sareng tiasa mancarkeun énergi frekuensi radio sareng, upami henteu dipasang sareng dianggo saluyu sareng petunjuk manual, tiasa nyababkeun gangguan anu ngabahayakeun kana komunikasi radio. Operasi pakakas ieu di wewengkon padumukan kamungkinan ngabalukarkeun gangguan ngabahayakeun, nu hal ieu pamaké bakal diperlukeun pikeun ngabenerkeun gangguan dina ongkos sorangan.

Pernyataan Patuh Regulasi FCC

§15.19 Pernyataan
Alat ieu saluyu sareng Bagian 15 Aturan FCC. Operasi tunduk kana dua kaayaan di handap ieu: (1) alat ieu moal ngabalukarkeun gangguan anu ngabahayakeun, sareng (2) alat ieu kedah nampi gangguan anu ditampi, kalebet gangguan anu tiasa nyababkeun operasi anu teu dipikahoyong.
Alat ieu saluyu sareng wates paparan radiasi FCC anu ditetepkeun pikeun lingkungan anu teu dikendali. Alat ieu kedah dipasang sareng dioperasikeun kalayan jarak minimum 20cm antara radiator sareng awak anjeun.

§15.21 Émbaran pikeun pamaké

Awas: parobahan atawa modifikasi teu dinyatakeun disatujuan ku pihak jawab minuhan bisa batal wewenang pamaké pikeun beroperasi alat.

Pernyataan patuh Paparan RF
This module complies with FCC radiation exposure limits set forth for an uncontrolled environment.. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

pernyataan minuhan ISED
Alat ieu ngandung pamancar/panarima anu dibebaskeun lisénsi anu saluyu sareng RSS anu dibebaskeun lisensi Inovasi, Élmu sareng Pangwangunan Ékonomi Kanada. Operasi tunduk kana dua kaayaan ieu:

1. Alat ieu moal ngabalukarkeun gangguan.
2.  Alat ieu kedah nampi gangguan naon waé, kalebet gangguan anu tiasa nyababkeun operasi alat anu henteu dipikahoyong.

Alat ieu saluyu sareng wates paparan radiasi IC RSS-102 anu ditetepkeun pikeun lingkungan anu teu terkendali. Alat ieu kedah dipasang sareng dioperasikeun kalayan jarak minimum 20cm antara radiator sareng awak anjeun.

Pernyataan Paparan Radiasi ISED
Alat ieu saluyu sareng wates paparan radiasi IC RSS-102 anu ditetepkeun pikeun lingkungan anu teu terkendali.
Please notice that if the IC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains IC: 35008-SRN”” any similar wording that expresses the same meaning may be used.

This radio transmitter [IC: 35008-SRN”] has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. If you desire to increase antenna gain and either change antenna type or use same antenna type certified, a Class II permissive change application is required to be filed by us, or you (host manufacturer) can take responsibility through the change in IC ID (new application) procedure followed by a Class II permissive change application. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.

Applicable FCC Rules Statement

This modular transmitter complies with FCC Rules Part 15.247, 15.407.

• Restricted Module Statement
  This printer mainboard module is not a restricted module and does not require additional compliance with restricted module-related procedures.
•  Antenna Design Statement
  The antenna supplied with this module is not a microstrip antenna. Therefore, information related to microstrip antenna design layout, Bill of Materials (BOM), and isolation requirements is not required.

1. This module complies with the radiation exposure limits set by the FCC for uncontrolled environments.
2.  When this module coexists with other simultaneously operating transmitters, compliance evaluation must be conducted in accordance with the FCC multiple transmitter procedures.

Antenna Usage Instructions and Compliance Statement

Antenna Specifications and Restrictions:

This device is authorized for use only with the antenna types listed in the table below. Use of uncertified antennas or antennas with gain exceeding the specified limits is strictly prohibited..

Jenis anteneu	Merk / produsén	Modél No.	Max. Antenna Gain
anteneu rod	IOE	366W0831	2.71 dBi

RSS-247 Clause  7.3.7 Compliance Statement

Pursuant to Clause 7.3.7 of Innovation, Science and Economic Development Canada (ISED) standard RSS-247, the following declarations are made:
Antenna Replacement Restriction:

1. This device is equipped with a removable antenna connector. Users must not arbitrarily replace the antenna type or use an antenna with gain exceeding the authorized limit.
2. Liability Statement: Any unauthorized antenna replacement or modification may cause the device to exceed permissible radiation emission limits and could result in the user losing legal authorization to operate the device. Should an antenna change be required, the manufacturer must submit a Permissive Change Application.
3. Interference Warning:
   1. Alat pikeun operasi dina pita 5150-5250 MHz ngan pikeun pamakéan jero rohangan pikeun ngurangan potensi gangguan ngabahayakeun pikeun ko-kanal sistem satelit mobile;
   2. Gain anteneu maksimum anu diijinkeun pikeun alat dina pita 5250-5350 MHz sareng 5470-5725 MHz kedah sasuai sareng wates eirp; jeung
   3. Gain anteneu maksimum anu diijinkeun pikeun alat-alat dina pita 5725-5825 MHz kedah saluyu sareng wates eirp anu ditangtukeun pikeun operasi point-to-point sareng non-point-to-point anu pas.

Daptar sadaya jinis anteneu

Jenis anteneu	Merk / produsén	Modél No.	Max. Antenna Gain
anteneu rod	IOE	366W0831	2.71 dBi

FAQ

Can I use any antenna with this module?

No, this device is authorized for use only with specific antenna types mentioned in the table provided in the user manual. Using uncertified antennas or those with gain exceeding specified limits is strictly prohibited.

Dokumén / Sumberdaya

Weihai Printer Mainboard Module [pdf] Buku Panduan Pamilik Printer Mainboard Module, Mainboard Module, Module

Rujukan

• Manual pamaké