PEMASANGAN INSTAL
CSEN1
CSEN1 Combo Sensor Controller
Part Numbers: CSEN1-H-W-ZHA (white enclosure) and CSEN1-H-G-ZHA (gray enclosure)
PEDARAN
The CSEN1 is a low voltage Networked Lighting Controller with an integrated passive infrared sensor and a photocell. It is powered via the AUX power from the LED driver. The CSEN1 autodetects both 0-10V Drivers and D4i Drivers to simplify the installation. The product is DLC certified for both indoor and outdoor applications.
SPESIFIKASI
- Frékuénsi Radio: 2.4 GHz (IEEE 802.15.4)
- RF Transmission Kaluaran Power: + 20dBM
- Suhu Operasi: -40 ° nepi ka +70 ° C
- Kalembaban Operasi: 10 nepi ka 95%, non-condensing
- IP66 Dipeunteun dipager
- Ukuran: 3.1 "D x 1.6" H (80mm D x 42mm H)
- Input Power: 12-24VDC, 35mA max, 840mW
- Tujuan kontrol: Operasi
- Environmental: Indoor/Outdoor
- Gelar polusi: 3
- Dipeunteun Impulse Voltagieu: 330v
PERTIMBANGAN DESAIN
Below are some recommendations for successful analog dimming using the CSEN1. The analog dimming control wires are referenced as DALI+/DIM+ and Common Ground/DALI-. The dimming signals have a Maximum voltage tina 10V DC.
- Do not ground the Common Ground/DALI- wire to chassis ground; this is a return signal and is critical for proper dimming.
- Rute dimming kawat jauh ti garis AC lamun mungkin.
- Maksimum 4 DALI-2 / D4i LED Supir per controller, konsultasi Synapse Rojongan lamun rasio gede diperlukeun.
- Maximum of 8 DIM to OFF LED Drivers for DIM to OFF Designs.
- Entong dipasang kana heatsink atanapi ka supir LED.
CATETAN: Supir LED kedah ngadukung fungsi DIM ka OFF.
WARNINGS AND PERHATOSAN
- TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT POWER IS OFF BEFORE INSTALLING OR SERVICING!
- The CSEN1 should only be installed in a fixture with a Zhaga Book 18 receptacle.
- Gagalna nuturkeun paréntah sareng peringatan ieu tiasa berpotensi ngabatalkeun jaminan.
- This product must be installed in accordance with national, state, and local electrical codes and requirements.
- If you are unsure about any part of these instructions, consult an electrician; qualified personnel should perform all work.
Rincian kabel ZHAGA BUKU 18 stop kontak
TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT POWER IS OFF BEFORE INSTALLING OR SERVICING!
For fixtures with an existing Zhaga socket, prior to installation, verify the wiring per the details below. (See Figure 1) If the fixture does not have a Zhaga socket, use the appropriate Wired Adapter accessory based on the knockout size: CSEN1-ZHA-ADPT-22 for 22mm knockouts, or CSEN1-ZHA-ADPT-33 for 33mm knockouts. The specifications for the signal wires are:
- 12-24VDC POWER: Brown
- Common Ground/DALI-: Pink with White Stripe
- DALI+/DIM+: Violet with White Stripe
- Solid Conductor, 105°C, Rated for 600VAC, AWG 20, 15” Length
GAMBAR 1 
PITUDUH INSTALASI
TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT POWER IS OFF BEFORE INSTALLING OR SERVICING!
- Upami tiasa, cabut tutup sealing atanapi alat kontrol cahaya anu ayeuna dipasang dina wadahna.
- Align the CSEN1 such that the contacts pins are positioned at the appropriate the receptacle contacts.
- After alignment, push until the CSEN1 is fully seated within the receptacle.
- While pushing against the device, twist the CSEN1 housing clockwise until it locks into place. The CSEN1 includes a latching key or notch that will lock into position with an audible “click”. (See Figure 2)
Catetan: Pikeun fungsina leres, pastikeun controller diselapkeun lengkep kana stop kontak jeung twisted kana posisi dikonci.
Awas: The Zhaga receptacle should not turn during installation. Turning the receptacle could damage the internal fixture wiring by pulling it loose.
GAMBAR 2
LED STATUS
| kakuatan LED | Status |
| Biru | On for 3 seconds at Startup, then Off |
| Status LED | Status |
| Beureum | No script on the device |
| Kedip-kedip Beureum | Kasalahan Komunikasi |
| Kedip-kedip Biru | Communication, No Config |
| Kedip-kedip Héjo | Normal Operation with Motion |
| Pareum | Normal Operation, no Motion |
INFORMASI REGULATOR JEUNG SERTIFIKASI
RF Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Sertifikasi Industri Kanada (IC): Aparat digital ieu henteu ngaleuwihan wates Kelas B pikeun émisi bising radio tina alat digital anu diatur dina Peraturan Interferensi Radio Departemen Komunikasi Kanada.
Sertifikasi FCC sareng inpormasi pangaturan (USA wungkul)
FCC Bagian 15 Kelas B: Alat ieu saluyu sareng bagian 15 aturan FCC. Operasi tunduk kana dua kaayaan di handap ieu: (1) Alat ieu moal ngabalukarkeun gangguan anu ngabahayakeun, sareng (2) Alat ieu kedah nampi gangguan anu ditampi, kalebet gangguan anu tiasa nyababkeun operasi ngabahayakeun.
RADIO FREQUENCY INTERFERENCE (RFI) (FCC 15.105): This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: (1) Re-orient or relocate the receiving antenna; (2) Increase the separation between the equipment and the receiver; (3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected; (4) Consult the dealer or an experienced radio/TV technician for help.
Declaration of Conformity (FCC 96-208 & 95-19): Synapse Wireless, Inc. declares that the product name CSEN1 to which this declaration relates, meet the requirements specified by the Federal Communications Commission as detailed in the following specifications:
- Bagian 15, Subbagian B, pikeun parabot Kelas B
- FCC 96-208 sabab manglaku ka komputer pribadi Kelas B sareng périferal
- Produk ieu parantos diuji di Laboratorium Uji Eksternal anu disertipikasi ku aturan FCC sareng parantos kapendak pikeun minuhan FCC, Bagian 15, Watesan Émisi. Dokuméntasi hurung file sareng sayogi ti Synapse Wireless, Inc.
Upami ID FCC pikeun modul di jero kandang produk ieu henteu katingali nalika dipasang di jero alat anu sanés, maka bagian luar alat dimana produk ieu dipasang ogé kedah nunjukkeun labél anu ngarujuk kana ID FCC modul anu ditutup. Modifikasi (FCC 15.21):
Parobihan atanapi modifikasi kana alat ieu anu henteu disatujuan ku Synapse Wireless, Inc., tiasa ngabatalkeun wewenang pangguna pikeun ngoperasikeun alat ieu.
Dipaténkeun - nyirian maya di https://www.synapsewireless.com/about/patents
Pikeun leuwih jéntré mangga buka: synapsewireless.com
SERTIFIKASI
| Modél | CSEN1-H-W-ZHA (white enclosure) or CSEN1-H-G-ZHA (gray enclosure) |
| Ngandung ID FCC | QOQ-GM240P |
| Ngandung IC | 5123A-GM240P |
| RoHS 3 | 2011/65/EU (2015/863) |
| EU ngahontal | (EC) No 1907/2006 |
DALI-2 Certified Aplikasi Controller
Dokumén / Sumberdaya
 |
Synapse CSEN1 Combo Sensor Controller [pdf] Pituduh instalasi CSEN1-H-W-ZHA, CSEN1-H-G-ZHA, CSEN1 Combo Sensor Controller, CSEN1, Combo Sensor Controller, Sensor Controller, Controller |