XP-8v
Advanced Control Processor
Panungtun Rujukan
XP-8v Advanced Control Processor
The XP-8v is a high-end remote control processor for automating the operation of electronic systems in homes and office buildings. The combination of a blazing fast MPU, real-time/multitasking operating system, and tremendous expansion capability, make the XP-8v the perfect solution for large-scale and complex projects.
The XP-8v provides superior quality and reliability as well as these features:
- Powerful 1GHz internal processor.
- 1GB of RAM memory and 512MB of non-volatile flash memory built in.
- SD/MM card slot allows memory expansion.
- Eight multi-purpose I/O ports.
- Eight programmable relay outputs.
- Eight two-way RS-232 ports.
- Eight sense inputs.
- Multi-purpose I/O ports are compatible with industry-standard IR emitters, blasters and repeater systems.
- Multi-purpose I/O ports support all optional RTI power sensing and communications modules.
- All output ports incorporate both short-circuit and overload protection.
- Kaluaran IR variabel dina sadaya palabuhan.
- Front panel controls/display (11 Buttons for front panel control).
- Non-volatile Flash memory stores your system configuration even when power is not present.
- Field upgradeable firmware.
- USB and Ethernet programming.
- Compatible with RTI 433MHz and 2.4GHz Zigbee RF modules.
- Astronomical clock built in for time-based event programming.
- Designed for rack mount or free standing installations.
Pamasangan & Operasi
PROGRAMMING THE XP-8v
The XP-8v must be programmed to operate. All programming is done using RTI’s Integration Designer software and is downloaded using the USB ® Programming Port located on front of XP-8v or via Ethernet.
NGEMASKEUN PERUSAHAAN
Disarankeun pisan yén ieu sareng sadaya produk RTI parantos dipasang firmware panganyarna. Firmware tiasa dipendakan dina bagian Dealer tina RTI websitus (www.rticontrol.com). Install the firmware using the USB Programming Port located on the front of XP-8v.
MPIO PORTS – Control via Infrared, Sensing and RS-232 (One-way)
INFRARED EMITTERS
The multi-purpose I/O ports on the XP-8v are compatible with industry standard infrared emitters and infrared repeating systems. Each output port is capable of driving up to four infrared emitters directly. The use of more than four infrared emitters requires the addition of an amplified connecting block. A connecting block can be wired up to 1000 feet away from the XP-8v using #22 AWG (minimum) wire.
INFRARED OUTPUT GAIN ADJUSTMENT
The IR output gain can be separately adjusted for each of the eight output ports. The XP-8v is shipped with the IR gain set to the optimum level for most equipment, and it should only need to be adjusted if the attached equipment is not responding reliably. If adjustment is needed, rotate the IR output controls on the front of the XP-8v clockwise for higher output power, or counter-clockwise for lower output power.
CATETAN: The IR output feedback LEDs located on the front of the XP-8v will illuminate when any IR code is delivered out of a port. This includes IR codes “passing through” from another source, such as an IR receiver.
VPS-1 SENSOR MODULE
The multi-purpose I/O ports on the XP-8v are compatible with RTI power sensing modules (e.g. VPS-1). Follow the guide included with the modules for installation instructions, and follow the instructions in the Integration Designers software for programming details.
RS-232 COMMUNICATION MODULES (CM-232)
The multi-purpose I/O ports on the XP-8v are compatible with RTI RS-232 communication modules (e.g. CM-232). Follow the guide included with the modules for installation instructions, and follow the instructions in the Integration Designer software for programming details.
RS-232 PORTS
The XP-8v is capable of two-way control using RS-232 communication via eight RJ-45 output ports using standard Cat-5/6 cable with RJ-45 termination (568B). The XP-8v ships with eight RJ-45 (female) to DB-9 (male) adapters.
IMPORTANT NOTE: RS-232 communication cabling should be limited to 50 feet (16m) depending on baud rate.
DB-9-RJ45 ADAPTOR PINOUT
RJ-45 (XP-8v RS-232 Output)
| Pin | Ngaran Sinyal | Pedaran sinyal |
| 1 | DSR | Siapkeun Data Siap |
| 2 | DCD | Pamawa Deteksi |
| 3 | DTR | Terminal Data Siap |
| 4 | GND | Signal Ground/Common |
| 5 | RXD | Nampi Data |
| 6 | TXD | Ngirimkeun Data |
| 7 | CTS | Hapus Pikeun Ngirim |
| 8 | RTS | Pamundut Pikeun Ngirim |
DB-9
| Pin | Ngaran Sinyal | Pedaran sinyal |
| 1 | DCD | Pamawa Deteksi |
| 2 | RXD | Nampi Data |
| 3 | TXD | Ngirimkeun Data |
| 4 | DTR | Terminal Data Siap |
| 5 | GND | Sinyal Ground |
| 6 | DSR | Siapkeun Data Siap |
| 7 | RTS | Pamundut Pikeun Ngirim |
| 8 | CTS | Hapus Pikeun Ngirim |
| 9 | NC | Teu Nyambung |
SENSE INPUTS / RELAY-TRIGGER OUTPUTS
Sense inputs and relay-trigger modes are configured within Integration Designer ® .
SENSE INPUT
Upon sensing contact closure or a voltage (2-24VDC), events can be automatically triggered such as a macro or command.
Sense contact closure: Connect conductors from the source device to each side of a sense input (A and B).
Rasa voltage pemicu: Connect positive lead from voltage source to Side A of sense input and ground lead to Side B.
RELAYS/TRIGGER OUTPUTS
Relays may be configured as a dry contact closure or a voltage trigger output (12VDC @100mA). All relays are Normally Open when not energized, and may be programmed to behave Normally Closed (as long as power is applied to the XP-8v).
Panutupanana kontak: Connect the A and B contact terminals of a relay to the device.
Voltage trigger: Connect contact A to the positive lead and connect Contact B to the ground lead of the device.
Ieu Dina Control ®
SIGNAL IN/HIGH OUT/POWER TERMINALS
TERMINAL: +12VDC
Positive power supply connection. It is internally tied to the Power jack. This can be used to power external IR or RF receivers.
TERMINAL: GROUND
Common ground connection. Use this ground reference for any device that is connected to the +12VDC, SIGNAL IN, OR HIGH OUT terminals.
TERMINAL: INPUT
Input connection for system trigger codes. This should be connected to an RTI RM433 RF receiver
or industry standard IR repeater system. The signal voltage can be from 3VDC – 12VDC.
TERMINAL: HIGH OUT
High current (200mA) IR output connection. This can be used to power up to 10 infrared mini-emitters, an IR blaster, or extending IR control over a long distance (1000 ft. max).
ETHERNET, USB, RTI COM, EXPANSION PORT
Ethernet
This RJ-45 port allows connection to a 10/100 Base-T Ethernet network (LAN).
Network settings such as the IP address are configurable within Integration Designer®.
Ethernet may also be used to download system files to the XP-8v.
USB PORTS (REAR)
These host ports for external devices are intended for future use.
RTI COM
This RJ-45 port allows connection to a ZM-24 Zigbee transceiver module for two-way communication with compatible RTI handheld controllers. Refer to the ZM-24 Zigbee transceiver module operation guide for installation instructions.
palabuan ékspansi
This RJ-45 port provides a convenient connection for receiving IR signals and two-way RS-485 communication from RTI in-wall controls through a CB-8 connecting block. NOTE: In-wall controllers may be connected directly to the XP-8v Expansion Port, however, they should be powered with a separate power supply.
POWER
SASAYOGIAN TANAGA
To power the XP-8v, use the supplied 12VDC/1Amp sasayogian tanaga.
XP-8v Front
Témbongkeun ménu
The display on the XP-8v is designed to give the installer feedback on the current status of the XP-8v, change settings such as the time/date and offer some basic diagnostic tools for troubleshooting. See XP-8v Display Technical Bulletin for detailed display menu options.
CATETAN
Any configuration changes made through the XP-8v display settings will be overwritten after the XP-8v is rebooted or an RTI system file is downloaded into the XP-8v memory.
FRONT PANEL LOCKOUT
It is possible to set a passcode that will block access to the menu system on the XP-8v. This can be set in the properties of the XP-8v within the RTI Integration Designer® programming software and downloaded as part of the system file. Use the cursor buttons on the XP-8v to enter the correct passcode to open the menu display.
MOUNTING
The XP-8v ships with four removable feet that allow the unit to be placed on a flat surface. The XP-8v can also be mounted in a component rack as part of a comprehensive control system. Remove feet before mounting in a rack.
Eusi Produk
- One (1) XP-8v Advanced Control Processor
- One (1) Power supply (12V, 1A)
- Eight (8) RJ45 to DB9 serial adaptors
- Two (2) Rack ears (2) with screws (8)
- Three (3) Terminal blocks (2 x 16-position, 1 x 4-position)
- One (1) Reference guide
- One (1) MAC address card
Saran Kasalametan
Read and Follow Instructions. Read all safety and operating instructions before operating the unit.
Retain Instructions. Keep the safety and operating instructions for future reference.
Heed Warnings. Adhere to all warnings on the unit and in the operating instructions.
Heat. Keep the unit away from heat sources such as radiators, heat registers, stoves, etc., including amplifiers anu ngahasilkeun panas.
Power Sources. Connect the unit only to a power supply of the type described in the operating instructions, or as marked on the unit.
Power Cord Protection. Route power supply cords so that they are not likely to be walked on or pinched by items placed on or against them, paying particular attention to the cord plugs at power receptacles and at the point at which they exit from the unit.
Water and Moisture. Do not use the unit near water—for example, deukeut tilelep a, dina basement basement, deukeut kolam renang, deukeut jandela muka, jsb.
Object and Liquid Entry. Do not allow objects to fall or liquids to be spilled into the enclosure through openings.
Servicing. Do not attempt any service beyond that described in the operating instructions. Refer all other service needs to qualified service personnel.
Damage Requiring Service. The unit should be serviced by qualified service personnel when:
- ari catu daya atawa colokan geus ruksak.
- Objek parantos murag atanapi cair parantos dituang kana hijian.
- Unit geus kakeunaan hujan.
- Unit kasebut henteu sigana beroperasi normal atanapi nunjukkeun parobihan anu jelas dina kinerja.
- Unit geus turun atawa dipager geus ruksak.
beberesih
To clean your XP8v, lightly dampen lawon bébas lint ku cai biasa atawa deterjen hampang tur usap surfaces luar.
CATETAN: Entong nganggo bahan kimia anu kasar sabab tiasa ngarusak unit.
Bewara Komisi Komunikasi Federal
Alat ieu geus diuji sarta kapanggih sasuai jeung wates pikeun alat digital Kelas B, nurutkeun Bagian 15 tina Aturan FCC. Watesan ieu dirarancang pikeun nyayogikeun panyalindungan anu wajar tina gangguan anu ngabahayakeun dina pamasangan padumukan. Sakur perobahan atawa modifikasi anu henteu sacara nyata disatujuan ku pihak anu tanggung jawab pikeun patuh tiasa ngabatalkeun wewenang pangguna pikeun ngoperasikeun alat.
Alat ieu ngahasilkeun, ngagunakeun, sareng tiasa mancarkeun énergi frekuensi radio sareng, upami henteu dipasang sareng dianggo saluyu sareng petunjuk, tiasa nyababkeun gangguan anu ngabahayakeun kana komunikasi radio. Nanging, teu aya jaminan yén gangguan moal lumangsung dina pamasangan khusus.
Upami alat ieu nyababkeun gangguan anu ngabahayakeun kana panarimaan radio atanapi televisi, anu tiasa dipastikeun ku cara mareuman sareng ngaktipkeun alat, pangguna didorong pikeun nyobian ngabenerkeun gangguan ku salah sahiji atanapi langkung tina ukuran ieu:
- Reorient atawa mindahkeun anteneu panarima.
- Ningkatkeun separation antara alat jeung panarima.
- Sambungkeun alat-alat kana stop kontak dina sirkuit béda ti nu disambungkeun ka panarima.
- Taroskeun ka dealer atanapi teknisi radio/TV anu berpengalaman pikeun pitulung.
Alat ieu saluyu sareng Bagian 15 Aturan FCC. Operasi tunduk kana dua kaayaan ieu:
- Alat ieu moal ngabalukarkeun gangguan anu ngabahayakeun.
- Alat ieu kedah nampi sagala gangguan anu ditampi kalebet gangguan anu tiasa nyababkeun operasi anu teu dipikahoyong.
Industri Kanada minuhan Pernyataan
Alat ieu saluyu sareng standar RSS anu dibebaskeun lisénsi Industri Kanada. Operasi tunduk kana dua kaayaan ieu:
- Alat ieu moal ngabalukarkeun gangguan anu ngabahayakeun.
- Alat ieu kedah nampi sagala gangguan anu ditampi kalebet gangguan anu tiasa nyababkeun operasi anu teu dipikahoyong.
Ngahubungan RTI
Pikeun warta ngeunaan apdet panganyarna, informasi produk anyar, jeung asesoris anyar, mangga buka kami web situs di: www.rticontrol.com
Kanggo inpormasi umum, anjeun tiasa ngahubungi RTI di:
Jauh Technologies Incorporated
5775 12th Ave. E Suite 180
Shakopee, Bungbulang 55379
Telp. 952-253-3100
info@rticontrol.com
Service & Rojongan
Upami anjeun ngalaman masalah atanapi gaduh patarosan ngeunaan produk RTI anjeun, mangga ngahubungi Rojongan Téknis RTI pikeun pitulung (tingali bagian Ngahubungan RTI dina pituduh ieu pikeun detil kontak).
RTI nyadiakeun rojongan teknis ku telepon atawa e-mail. Pikeun layanan kualitas pangluhurna, mangga siapkeun inpormasi ieu:
- Nami anjeun
- Nami Perusahaan
- Nomer Telepon
- Alamat email
- Model produk sareng nomer séri (upami aya)
Upami anjeun gaduh masalah sareng hardware, punten perhatikeun peralatan dina sistem anjeun, pedaran ngeunaan masalahna, sareng cara ngungkulan naon waé anu anjeun parantos nyobian.
*Punten ulah mulangkeun produk ka RTI tanpa otorisasina.*
Garansi kawates
RTI ngajamin produk anyar salami tilu (3) taun (henteu kalebet bahan konsumsi sapertos batré anu tiasa dicas deui anu dijamin salami hiji (1) taun) ti tanggal pameseran ku pembeli asli (pamaké akhir) langsung ti RTI / Pro Control ( di dieu disebut "RTI"), atawa dealer RTI otorisasi.
Warranty claims may be initiated by an authorized RTI dealer using the original dated sales receipt or other proof of warranty coverage. In the absence of the receipt of purchase from the original dealer, RTI will provide warranty coverage extension of six (6) months from the date code of the product.
Catetan: RTI warranty is limited to the provisions set forth in this policy and does not preclude any other warranties offered by third parties who are solely responsible for those other warranties.
Iwal sakumaha dieusian di handap, jaminan ieu nyertakeun defects dina bahan produk jeung workmanship. Di handap ieu teu katutupan ku jaminan:
- Produk dibeuli via sellers diidinan atawa situs internét moal serviced- paduli tanggal beuli.
- Karuksakan anu disababkeun ku kacilakaan, nyalahgunakeun, nyiksa, ngalalaworakeun atanapi tindakan Gusti.
- Karusakan kosmetik, kalebet, tapi henteu dugi ka, goresan, dents sareng ngagem sareng cimata normal.
- Gagal nuturkeun paréntah anu aya dina Pitunjuk Instalasi Produk.
- Karuksakan alatan produk dipaké dina aplikasi atawa lingkungan lian ti nu eta dimaksudkeun, prosedur instalasi teu bener atawa faktor lingkungan ngarugikeun kayaning vol line salah.tages, kabel teu bener, atawa ventilasi cukup.
- Ngalereskeun atanapi nyobian ngalereskeun ku saha waé salian ti RTI sareng Pro Control atanapi mitra jasa anu sah.
- Gagal ngalaksanakeun pangropéa périodik anu disarankeun.
- Ngabalukarkeun lian ti defects produk, kaasup kurangna skill, kompetensi atawa pangalaman pamaké.
- Karusakan kusabab kiriman produk ieu (klaim kedah dilakukeun ka pamawa).
- Unit dirobah atawa nomer serial dirobah: defaced, dirobah atawa dihapus.
RTI Control ogé henteu nanggungjawaban kanggo:
- Karuksakan anu disababkeun ku produkna atanapi kusabab gagalna produkna, kalebet biaya tenaga kerja, kaleungitan kauntungan, kaleungitan tabungan, karusakan saliwatan, atanapi karusakan akibat.
- Karuksakan dumasar kana kasulitan, leungitna pamakéan produk, leungitna waktu, operasi interrupted, leungitna komérsial, sagala klaim dijieun ku pihak katilu atawa dijieun atas nama pihak katilu.
- Leungitna, atawa ruksakna, data, sistem komputer atawa program komputer.
RTI’s liability for any defective product is limited to repair or replacement of the product, at the sole discretion of RTI.
In cases where the warranty policy conflicts with local laws, the local laws will be adopted.
PERNYATAAN KEUNTUNGAN (DOC)
Déklarasi Conformity pikeun produk ieu tiasa dipendakan dina RTI websitus di: www.rticontrol.com/declaration-of-conformity
Hak Cipta © 2025
Jauh Technologies Incorporated
Sadaya hak disimpen.
Dokumén / Sumberdaya
 |
RTI XP-8v Advanced Control Processor [pdf] Pituduh pamaké XP-8v Advanced Control Processor, XP-8v, Advanced Control Processor, Control Processor, Processor |