SteadyWin GIM4310-10 Planetary Reducer Servo Motor User Guide

GIM4310-10 Planetary Reducer Servo Motor

Product Specifications

  • Thread Depth: 3mm for 6-M2.5 screws
  • Thread Depth: 4mm for 3-M3 screws
  • General Tolerances: Per ISO 2768-m(x)

Product Usage Instructions

Mounting Instructions

Ensure screws are not excessively long to prevent motor damage.
Use appropriate screw sizes based on the thread depth
specified.

Front Cover Installation

If the front cover is omitted, ensure that the bearing is
properly contained. The no-front cover state can be applied when
the motor mounting position can contain the bearing, reducing
installation height. This state is an unfinished structure before
installation is complete. Do not test until the motor is secured,
as there is a risk of the motor coming out.

Brake Installation

Refer to the GIM4310-10 Brake Installation Drawing for detailed
instructions on installing the brake component.

Frequently Asked Questions (FAQ)

Q: What should I do if my screws are too long?

A: Using screws that are excessively long can lead to motor
damage. Ensure to use screws of the appropriate length as per the
specified thread depth to avoid any issues.

Q: Can I proceed with installation without the front
cover?

A: If the front cover is omitted, make sure that the bearing is
properly contained. Only proceed without the front cover if the
motor mounting position can securely hold the bearing to reduce
installation height. However, do not perform any testing until the
motor is fully secured to prevent any accidents.

Q: Where do I find information on brake installation?

A: Refer to the GIM4310-10 Brake Installation Drawing for
detailed instructions on how to install the brake component
correctly.

“`

8 H
G

7
6-M2.5 THREAD DEPTH 3mm
Scr ews must not be excessi vel y l ong. Ot her wi se, mot or damage may occur .

F

6
Ø47.5

5

4

3

31 1

19

6

Ø53 Ø37

Ø40

2

1

H

3-M2.5 EFFECTIVE THREAD DEPTH 5mm Ø47.5 Ø27
G
3-M3 EFFECTIVE THREAD DEPTH 4mm

F

E D C B A
8

6-M2.5 THREAD DEPTH 3mm
Scr ews must not be excessi vel y l ong. Ot her wi se, mot or damage may occur .

Ø47.5

28 2
2

19

6

Ø53 Ø44 Ø37

Ø40

FRONT COVER OMITTED
The f ont cove f unct i ons t o const ai n t he bea i ng. The no-f ont cove st at e appl i es when t he mot o mount i ng posi t i on can const ai n t he bea i ng, use t o e uce i nst al l at i on hei ght . Thi s st at e i s an unf i ni she st uct u e bef o e i nst al l at i on i s compl et e . Do not t est
un t he mot o , ot he wi se t he e i s ange of t he ot o comi ng out .
GENERAL TOLERANCES PER ISO 2768-m(x)

SCALE

7

6

5

4

3

E

6-M2.5 EFFECTIVE THREAD DEPTH 5mm Ø47.5

Ø27

3-M3 EFFECTIVE THREAD DEPTH 4mm

D

C

B GIM4310-10 BRAKE INSTALLATION DRAWING

A

2

1

Documents / Resources

SteadyWin GIM4310-10 Planetary Reducer Servo Motor [pdf] User Guide
GIM4310-10, 4310-10SHS, GIM4310-10 Planetary Reducer Servo Motor, GIM4310-10, Planetary Reducer Servo Motor, Reducer Servo Motor, Servo Motor, Motor

References

Leave a comment

Your email address will not be published. Required fields are marked *