ON Semiconductor NCN5100 Arduino Shield Evaluation Board
Tlhahisoleseding ya Sehlahiswa
Litlhaloso
- Lebitso la Sehlahiswa: Boto ea Tlhahlobo ea NCN5100 Arduinot Shield
- Nomoro ea Mohlala: EVBUM2715/D
- Tšebelisano: Mefuta e mengata e fapaneng ea liboto tsa ntlafatso ea microcontroller
- Transceiver: E lumellana ka botlalo le KNX
- Khumo Voltage: 3.3 V (e tsitsitseng), 1.2 V ho isa ho 21 V (e feto-fetoha)
- Khokahano: Likhokahano tsa puisano tsa SPI le UART
Fetileview
NCN5100 Arduinot Shield Evaluation Board ke thebe e lumellanang le Arduino e lumellang prototyping e potlakileng e nang le microcontroller ea khetho. E lumellana ka botlalo le mefuta e mengata e fapaneng ea liboto tsa nts'etsopele ea microcontroller. Thebe e kenyelletsa likarolo tsohle tse hlokahalang tsa kantle bakeng sa ho sebetsa li-transceivers. Ka ho hokela thebe ho lisebelisoa tsa nts'etsopele tse lumellanang le Arduino, basebelisi ba ka qala ho nts'etsapele merero ea bona hanghang.
Likaroloana
- E lumellana le mefuta e mengata e fapaneng ea liboto tsa nts'etsopele ea microcontroller
- Transceiver e lumellanang le KNX ka botlalo
- 3.3 V tlhahiso e tsitsitseng, 1.2 V ho 21 V tlhahiso e fapaneng
Maboto a Tlhahlobo
NCN5100 Arduinot Shield Evaluation Board e tla ka mefuta e meraro, e 'ngoe le e' ngoe e na le mofuta o fapaneng oa transceiver: NCN5110, NCN5121, le NCN5130. NCN5110 ke transceiver hanyane moo linako tsohle li sebetsoang ke microcontroller. Ka lehlakoreng le leng, NCN5121 le NCN5130 ka bobeli li kenya tšebetsong sekhahla sa MAC, ho fokotsa boiteko ba nts'etsopele ea software. Li-transceivers tsena li kenyelletsa li-converter tse peli tse sebetsang hantle haholo tsa DC-DC. Mofetoleli oa pele o hlahisa tlhahiso e tsitsitseng ea 3.3 V ho fana ka transceiver le lisebelisoa tse ling. Mofetoleli oa bobeli o na le phallo e feto-fetohangtage ho tloha ho 1.2 V ho isa ho 21 V, e ka sebelisoang ho matlafatsa lisebelisoa tse ling tse kang li-relay kapa lipontšo. Liboto li entsoe ka Arduino shield form factor, e etsang hore ho be bonolo ho qala ka ho hokela thebe ka har'a boto ea microcontroller e lumellanang.
Evaluation Board Overview
Khokahano ea mantlha ho boto ea tlhahlobo e fanoa ka lihlooho tsa Arduino V3. Sena se lumella boto hore e lumellane le mefuta e mengata e fapaneng ea liboto tsa ntlafatso ea microcontroller. Ka kopo sheba Sehlomathiso C, Lethathamo la 6 ho Buka ea Mosebelisi bakeng sa lethathamo la liforomo tse lekiloeng.
KNX-Bus
KNX-bese ke thapo e sothehileng e sebetsang e le mokhoa o ka sehloohong oa puisano. E fana ka khokahanyo ho lisebelisoa tsa ntlo kapa mohaho oa mochine o ikemetseng.
Moqtage Pins
- VBUS: Bese voltage
- Veq: Equilibrium voltage
- Vact: Matla a voltage
- Vend: Qetello ea mohala voltage
- VDC: DC voltage
Fan-in
Sesebelisoa se seng le se seng se hokahaneng le bese ea KNX se tla hula hajoale. Pini ea fan-in letlapeng la tlhahlobo e beha boholo ba hajoale bo huloang beseng. Transceiver e boloka ea hona joale ka tlase ho moeli o behiloeng.
Ka bobeli li-transceivers tsa NCN5121 le NCN5130 li na le mekhoa e 'meli e hlalositsoeng esale pele ea fan-in. Mefuta ena e ka khethoa ka ho hokela pinana ea fan-in ho GND kapa ho e siea e phaphametse. Ha e tlohetsoe e phaphametse, palo e phahameng ea libese e lekanyelitsoe ho 10 mA. Ha o hokahantsoe le GND, moeli o behiloe ho 20 mA.
Litaelo tsa Tšebeliso ea Sehlahisoa
Mohato oa 1: Ho theha Hardware
- Netefatsa hore boto ea ntlafatso ea microcontroller e lumellana le NCN5100 Arduinot Shield Evaluation Board.
- Kenya thebe ho lihlooho tsa Arduino V3 tsa boto ea nts'etsopele ea microcontroller.
- Hokela lisebelisoa life kapa life tsa tlatsetso, joalo ka li-relay kapa likhalase, ho thebe ha ho hlokahala.
Mohato oa 2: Phepelo ea Matla
Netefatsa hore phepelo ea motlakase bakeng sa boto ea nts'etsopele ea microcontroller e hokahane le ho fana ka matla a lekanengtage.
Mohato oa 3: Tsoelo-pele ea Software
- Kenya tikoloho e hlokahalang ea nts'etsopele ea software bakeng sa microcontroller, haeba e se e entsoe.
- Ngola kapa kenya khoutu eo u e batlang tikolohong ea nts'etsopele ea software.
- Kopanya le ho kenya khoutu ho boto ea nts'etsopele ea microcontroller.
Mohato oa 4: Teko
Hang ha khoutu e kentsoe, u ka qala ho hlahloba morero oa hau u sebelisa likonopo tse ka holim'a board le li-LED tse fanoeng thebe. Ha ho lithebe tse ling tse hlokahalang bakeng sa tlhahlobo ea mantlha. Bakeng sa mohlalaample, o ka theha sesebelisoa se bonolo sa dimmer o sebelisa thebe ea KNX Arduino feela.
Mohato oa 5: Tsoelo-pele e Tsoelang Pele
Haeba o lakatsa, o ka tsoela pele ho nts'etsapele projeke ea hau ka ho hokela lisebelisoa tse ling le ho holisa ts'ebetso ea ts'ebeliso ea hau. Sheba Bukana ea Mosebelisi bakeng sa lintlha tse felletseng mabapi le ho sebelisa mofuta o ikhethileng oa transceiver le likarolo tsa ona.
FAQs
- P: Ke liboto life tsa ntlafatso ea microcontroller tse lumellanang le NCN5100 Arduinot Shield Evaluation Board?
- A: NCN5100 Arduinot Shield Evaluation Board e tsamaisana le mefuta e mengata e fapaneng ea liboto tsa ntlafatso ea microcontroller. Ka kopo sheba Sehlomathiso C, Lethathamo la 6 ho Buka ea Mosebelisi bakeng sa lethathamo la liforomo tse lekiloeng.
- P: Morero oa pin-in pin mabapi le tlhahlobo ke ofe boto?
- A: Pini ea fan-in e beha boholo ba hajoale bo nkiloeng ho bese ea KNX. E ka hokeloa ho GND kapa ka ho le letšehali e phaphametse ho khetha mefuta e fapaneng ea li-fan-in, tse khethollang moeli oa libese oa hajoale.
- P: A na nka matlafatsa li-peripherals tse ling ke sebelisa tlhahlobo boto?
- A: Ee, boto ea tlhahlobo e kenyelletsa converter ea bobeli ea DC-DC e nang le sephetho se feto-fetohangtage ho tloha ho 1.2 V ho ea ho 21 V. Sena se ka sebelisoa ho matlafatsa li-peripherals tse kang li-relay kapa lipontšo.
LIEKETSENG
KNX [3] ke lehae le tsebahalang le bulehileng le ho aha maemo a1. ON Semiconductor e na le letoto la li-transceivers tse sebetsanang le puisano e tlaase.
Liboto tsa tlhahlobo tsa NCN5100ASGEVB ke lithebe tse lumellanang le Arduino tse nolofalletsang prototyping e potlakileng e nang le microcontroller ea khetho. Likarolo tsohle tsa kantle tse hlokahalang bakeng sa ho sebetsa li-transceivers li teng ho thebe. E kenye ka har'a lisebelisoa tsa nts'etsopele tse lumellanang le Arduino 'me u qale ho e ntlafatsa!
LIKAROLOANA
-
Lihokelo tse lumellanang tsa Arduino Uno V3
- E lumellana le mefuta e mengata e fapaneng ea liboto tsa nts'etsopele ea microcontroller
- Likonopo / li-LED tse 'ne ho aha sesebelisoa sa dimmer
- E fumaneha ka mofuta oa UART le SPI
- Transceiver e lumellanang le KNX ka botlalo
- Ho bonolo ho qala ka KNX
- Bolelele ba libese hajoale bo fihla ho 40 mA2
- Li-converter tse peli tse sebetsang hantle haholo tsa DC-DC
- 3.3 V tlhahiso e tsitsitseng
- 1.2 V ho ea ho 21 V tlhahiso e fapaneng
- Sephetho se kopantsoeng sa 20 V linear regulator
FEELAVIEW
Liboto tsa NCN5100ASGEVB li tla ka mefuta e meraro e nang le li-transceivers tsa NCN5110, NCN5121 le NCN5130. NCN5110 ke transceiver hanyane mme linako tsohle li sebetsoa ke microcontroller. Ka bobeli NCN5121 le NCN5130 le tsona li kenya tšebetsong lera la MAC, ho fokotsa boiteko ba nts'etsopele ea software. Linako tsohle tse mahlonoko li sebetsoa ke transceiver.
Li-transceivers tsohle li kenyelletsa li-converter tse peli tsa DC-DC tse sebetsang hantle haholo. Mofetoleli o le mong o tsitsitseng o hlahisang 3.3 V, o fana ka transceiver le lisebelisoa tse ling tsa boikhethelo tse kang microcontroller. Mofetoleli oa bobeli oa DC-DC o na le phallo e feto-fetohangtage ho tloha ho 1.2 V ho isa ho 21 V 'me e ka sebelisoa ho fana ka lisebelisoa tse kang, li-relay, pontšo, joalo-joalo ...
Arduino thebe form factor e etsa hore ho be bonolo ho qala ho nts'etsapele; feela hokela thebe ka har'a boto ea microcontroller e lumellanang 'me u qale ho khouta. Ka lebaka la likonopo le li-LED, ha ho hlokahale ho kenya lithebe tse eketsehileng ho qala tlhahlobo. Sesebelisoa se bonolo sa dimmer se ka hlophisoa ka nako leha e le efe ka KNX Arduino-thebe feela.
1 https://my.knx.org
2 Bakeng sa mofuta oa NCN5130 le NCN5110. NCN5121 e nyolohela ho 24 mA.
Ka bobeli NCN5121 le NCN5130 li tla le sebopeho sa puisano sa SPI le UART. Ea ho qetela e lumellana ka botlalo le TP-UART, e nolofalletsang tšebeliso ea software e teng e lumellanang.
Liboto ke 2 layer PCB's tse nang le kopano e lehlakoreng le le leng, e bonts'ang hore hoa khoneha ho hlahisa lits'ebetso tse theko e tlase habonolo.
LEBOTO LEKOLOVIEW
Khokahano ea mantlha ho boto ea tlhahlobo e fanoa ka lihlooho tsa Arduino V3 tse ka bonoang ho Setšoantšo sa 1. 
Sena se na le advantage hore boto e lumellana le mefuta e mengata e fapaneng ea liboto tsa ntlafatso ea microcontroller. Sheba Sehlomathiso C, Lethathamo la 6 bakeng sa lethathamo la li-platform tse lekiloeng.
KNX-Bus
KNX-bese e na le thapo e sothehileng e fanang ka data le matla ka bobeli. Molumotage ka bese e fapana pakeng tsa 21 V ho 32 V (VDC ho Figure 3). Puisano ka bese e etsoa ka 9600 baud asynchronously. A logic one e emetsoe ke DC-level ka beseng e lula e sa fetohe. Bakeng sa zero ea logic, bese e huloa 3 V ho 10 V ka tlase ho boemo ba DC pele. Sena se bitsoa "active pulse" e nang le nako ea 35 s. Ho latela hang-hang ka mor'a moo ke sekhahla sa ho lekana. Nakong ena, voltage ka suthela ho 13 V ka holimo ho boemo ba DC 'me e tla bola haholo ka 69 µs.
Setšoantšo sa 3 se bontša sebopeho se tloaelehileng sa maqhubu ka beseng se emelang zero e utloahalang.
Fan-in
Sesebelisoa se seng le se seng se hokahaneng le bese ea KNX se tla hula hona joale ka bese ho fana ka ts'ebeliso. Tekanyetso ea KNX e bolela hore hajoale e lokela ho lekanyetsoa ho tlhoko ea 'nete. Bakeng sa sesebelisoa se seng le se seng sa KNX palo e kholo ea hajoale e hlahisoa ho database ea eona ho latela fan-in-model [1]. Fan-in-model e sebelisoa ho fumana hore na ke lisebelisoa tse kae tse ka hokeloang karolong e le 'ngoe ea bese. Li-transceiver tsohle tsa ON Semiconductor KNX li na le mochini o hahelletsoeng ka hare ho boloka toro ka har'a boleng bo boletsoeng ho database ea eona. Sena se etsa bonnete ba hore sesebelisoa se lumellana le maemo.
Pini ea fan-in e beha boholo ba hajoale bo nkiloeng beseng. Transceiver e tla boloka ea hajoale ka tlase ho moeli o behiloeng.
Li-transceivers ka bobeli (NCN5121 le NCN5130) li na le mekhoa e 'meli e hlalositsoeng esale pele ea fan-in. Tsena li ka khethoa ka ho hokahanya pini ea fan-in ho GND kapa ho e siea e phaphametse. Ha e e siea e phaphametse, palo e phahameng ea libese e lekantsoe ho 10 mA. E tlameletsoe ho GND moeli o behiloe ho 20 mA.
NCN5130 e boetse e fana ka mokhoa oa kantle oa fan-in. Ka mokhoa ona moeli oa hona joale o ka behoa ka mokhoa o tloaelehileng ho tloha ho 5 mA ho ea ho 40 mA. Sena se finyelloa ka ho hokahanya khanyetso e nang le boleng ba 10 k
ho ea ho 93.1 k ho phini ea fan-in. Fan-in-model [1] e totobatsa lihlopha tsa hajoale tse ikhethileng. Ha o rala kopo le ho hlalosa tšebeliso ea hona joale, boleng bo latelang bo phahameng ba e 'ngoe ea lihlopha bo tlameha ho khethoa. Ho ea ka karolo ea 3.3 ea tlhahlobo ea tlhahlobo ea KNX [2] boholo bo lumelletsoeng ho sebelisoa ha libese hona joale bakeng sa fan-in-model ea 10 mA ke 12 mA. Bakeng sa mefuta e meng ea fan-in e lumelloa ho lekanya boleng bona ka nepo. Bakeng sa mohlalaample, 20 mA fan-in-model e lumella ho hula 24 mA ho tloha bese.
Lethathamo la 1. LITABA TSA LITŠOANTŠISO TSE KHOTHATSENG TSA BARATI
|
R3 |
Ibese, lim (E tloaelehileng Litekanyetso) | Sehlopha sa Hona joale
(Tlhaloso ea 1) |
| ∞ | 11.4 mA | 10 mA |
| 0 Q | 22.3 mA | 20 mA |
| 10kq | 43.9 mA | 40 mA |
| 13.3kq | 33.0 mA | 30 mA |
| 20kq | 22.1 mA | 20 mA |
| 42.2kq | 10.7 mA | 10 mA |
| 93.1kq | 5.1 mA | 5 mA |
1. Ho ea ka fan-in-model [1].
Lethathamo la litekanyetso tse khothaletsoang tsa ho hanyetsa li-fan-in li ka fumanoa ho Lethathamo la 1. Bakeng sa litekanyetso tse thathamisitsoeng tsa mohanyetsi, meeli ea hona joale e tsamaellanang e hlalositsoe ka har'a database.
Haeba boleng ba sehanyetsi bo sebelisoa, ntle le bo boletsoeng ho Lethathamo la 1, ho ka sebelisoa mokhoa o latelang ho bala moeli oa libese o tsamaellanang le ona:
Buffer Capacitor
Ntle le boholo ba hajoale bo lumelletsoeng bo huloang beseng, maemo a KNX a boetse a bolela hore na lebelo la libese le lumelletsoeng ho fetoha ka lebelo lefe. Tlhokahalo ena e hlahisa tlhoko ea buffer capacitor e kholo. Ha mojaro oa hona joale o fetoha ka tšohanyetso capacitor ena e tlameha ho fana ka matla a hlokahalang. KNX-transceiver e tla lefella capacitor hape ka mor'a mohato oa mojaro o sebelisa moepa o tsitsitseng oa hona joale.
Ho ea ka tlhahlobo ea tlhahlobo ea KNX [2] sesebelisoa se nang le fan-in-model ea 10 mA se lumelloa ho fetola setšoantšo sa eona sa hona joale ho tloha beseng e nang le moepa oa 0.5 mA / ms. Karolo ea 3.3 e bolela hore sena se ka eketsoa ka mokhoa o nepahetseng ka fan-in-model. Ho ka sebelisoa foromo e latelang ho bala moepa oa hona joale oa bese o lumelletsoeng: database (maqephe 18−19) ea NCN5121/NCN5130 e hlalosa mokhoa oa ho lekanya capacitor ea buffer. KNX Family Efficiency Calculator3 ke sesebelisoa se ntlafalitsoeng ho thusa bareki ka boemo bona.
Tloaelehileng Mode Choke
Haeba o lakatsa, mokhoa o tloaelehileng oa ho choke joalo ka Murata 50475C o ka beoa mosikong oa L1. Sena se thusa ho thibela litšitiso tsa mokhoa o tloaelehileng, empa lits'ebetsong tse ngata, sena ha se hlokehe.
Pele o koala sekheo sebakeng se boletsoeng esale pele sa L1, lipina tse khutsufatsang karolo li tlameha ho khaoloa.
3 https://www.onsemi.com/pub/Collateral/KNX%20FAMILY%20EFFICIENCY%20CALCULATOR.XLSM
Matla
Boto e tsamaisoa ka sehokelo sa KNX. Lithakhisa tsena tse peli (KNX+/KNX- ho Setšoantšo sa 9) li kopana le boloko bo tloaelehileng ba KNX joalo ka Wago 243−211, e bontšitsoeng ho Setšoantšo sa 5. Ha ho hlokahale hore ho be le khokahanyo e eketsehileng kaha boto e tla iketsetsa phallo ea eona.tages. Kenyelletso voltage ho fihlela ho 30 V e mamelloa. Ho sebelisa motlakase o tloaelehileng oa KNX ke khetho e sireletsehileng ka ho fetisisa kaha e hlahisa molumo o nepahetsengtage mme e na le tshireletso e hahelletsoeng ka hare.
Hoa khoneha ho sebelisa phepelo ea laboratori, empa etsa bonnete ba hore u beha molumo o nepahetseng ka nepotage ho qoba ho senya letlapa. Ka ho sebelisa matla a laboratori, ho ke ke ha khoneha ho romela melaetsa ho KNX-bese. Ho etsa hore puisano e be teng beseng, ho tlameha hore ho behoe choke e khethehileng lipakeng tsa phepelo ea motlakase le boto ea ntlafatso. Example ea choke joalo ke Siemens GAMMA Choke N 120/02.
Ho matlafatsa boto ea ntlafatso ea microcontroller ho na le likhetho tse 'maloa.
- Liboto tse ngata tsa morao-rao tsa nts'etsopele ea li-microcontroller li ka fanoa ka 3V3-pin, sena se felisa tlhoko ea LDO's e eketsehileng, mme se theola tšebeliso ea matla ka kakaretso.
Ho thebe, kamehla ho na le 3.3 V phepelo e teng, e sebelisoang hape ho fana ka transceiver ea KNX. Phepelo ena voltage ka fetisetsoa ho 3V3-pin ho lihlooho tsa Arduino ka ho khutsufatsa J11 (Setšoantšo sa 6). - Maboto a ntlafatso a lumellanang le Arduino hangata a amohela phallo ea voltage ea 7 V ho 12 V, ebang ke ka on-board DC-jack (haeba e teng) kapa VIN-pin lihloohong.
Thebe e ka fana ka microcontroller ka VIN-pin. Ha J10 e khutsufatsoa (bona Setšoantšo sa 6), 9 V e hlahisoang ke DC-DC2 e fetisetsoa ho VIN-pin. Tokisong ena, sistimi eohle e fanoa ka bese ea KNX mme ha ho hlokahale lisebelisoa tse eketsehileng tsa motlakase. - Boto ea ntlafatso ea microcontroller e ka fanoa ka phepelo ea kantle. Sena se etsahala ha u lokisa boto ka USB ka sehokelo sa KNX se khaotsoe. Tabeng ena tlosa ka bobeli J10 le J11 (Setšoantšo sa 6).
Ho lokisa boemo ba DC-DC2 Output Voltage
DC-DC2 ea fetoha 'me e ka hlophisoa hore e hlahise voltage pakeng tsa 1.2 V ho 21 V. Sena se nolofalletsa ho fana ka mefuta e mengata haholo ea likopo. Ka kamehla, tlhahiso ea voltage e behiloe ho 9 V. Sena se etsa hore e be se loketseng ho fana ka boto ea ntlafatso e lumellanang le Arduino, eo ka tloaelo e amohelang mefuta e mengata ea ho kenya 7 V ho 12 V.
Ho lokisa sephetho sa voltage, boleng ba bahanyetsi ba maikutlo bo tlameha ho fetoloa. Tsena li fumaneha hukung e ka tlase letsohong le letšehali la PCB, ho etsa hore li rekisoe habonolo. Litekanyetso tse hlokahalang tsa resistor li ka baloa ho tloha:
Kapa sebelisa KNX Family Efficiency Calculator4 e ka fumanoang ho ON Semiconductor websebaka.
Lintho tse kenang le tse hlahisoang
Arduino Header Pin-Out
Bongata ba likonopo le li-LED li hokahane le likhoele tsa dijithale lihloohong tsa Arduino. Likonopo tse peli le LED e le 'ngoe li hokahane le lithakhisa tsa analog. Sena se entsoe ho boloka I2C-pins e lokolohile bakeng sa merero e meng. Hoa tšoana le ho TREQ-pin.
SAVEB-pin e hoketsoe ho phini ea dijithale e nang le bokhoni ba ho sitisa. Sena sea hlokahala ho fana ka lets'oao ho microcontroller kapele kamoo ho ka khonehang ho bonts'a molumo oa besetage ea theoha.
Li-LED tsohle li hokahane le lithakhisa tse nang le bokhoni ba PWM, tse lumellang sesebelisoa ho fifatsa li-LED ha li lakatsa. Lenane le felletseng la likhokahanyo tsa microcontroller le fanoe ho Sehlomathiso A, Lethathamo la 4 le ho Sehlomathiso B, Lethathamo la 5.
4 https://www.onsemi.com/pub/Collateral/KNX%20FAMILY%20EFFICIENCY%20CALCULATOR.XLSM
Likonopo tsa basebelisi le li-LED
Thebe e na le likonopo tse 4 tse on-board (SW1…4) le li-LED tse 4 (LED2…5) ho etsa hore ho be le nts'etsopele ea li-switching app ka ho khetheha. Bakeng sa ts'ebeliso ea dimmer likonopo tse 'ne li arotsoe ka lihlopha tse peli tse tšoailoeng ho PCB joalo ka channel1 le channel2 (CH1/CH2). Konopo e ka holimo ea kanale e sebelisetsoa ho fifatsa, ha e 'ngoe e sebelisetsoa ho fifatsa. Sheba Sehlomathiso A, Lethathamo la 4 le Sehlomathiso B, Lethathamo la 5 ho bona hore na tsena li hokahane joang le lithakhisa tsa I/O tsa microcontroller.
Hoa khoneha ho bokella lithebe tse ling tse nang le li-I/O tse sebelisoang bakeng sa kopo ea ho qetela. Tlosa R26−R29 le R33−R36 haeba likonopo kapa li-LED li thulana le pin-out ea lithebe tse ling tse sebelisitsoeng.
Programming Push Button le LED
Ho abela aterese ea motho ka mong ho sesebelisoa ho KNX-network, sesebelisoa se tlameha ho kenngoa mokhoeng oa ho hlophisa. Mokhoa o bonolo oa ho etsa sena ke ka ho tobetsa konopo ea programming (S1). LED6 e bonts'a haeba sesebelisoa se le maemong a ho etsa mananeo.
Hoa khoneha ho etsa mokhoa oa ho kenya ka mokhoa oa ho etsa mananeo, mohlala, ho sututsa likonopo tse peli ka nako e le 'ngoe.
Ho koaloa ha Microcontroller
NCN5130 le NCN5121 li na le bokhoni ba ho fana ka letšoao la oache ho microcontroller. Letšoao lena la oache le fumaneha ho XCLK-pin ea transceiver mme le fetisetsoa ho pin ea hlooho ea 2.54 mm holim'a thebe (Sheba Setšoantšo sa 9). Hobane lihlooho tsa Arduino ha li bone esale pele phini e inehetseng ho fetisa matšoao a oache, hoa tlameha ho tsamaisa lets'oao lena ka letsoho ho ea ho microcontroller. Sena se hlokahala feela haeba ho lakatseha ho sebelisa lets'oao lena ho koala microcontroller. Maemong a mangata microcontroller e tla koaloa ho tloha ka hare ho RC-oscillator kapa ho tloha kristale e ka ntle.
Ka kamehla, lets'oao la oache ho XCLK-pin ke 16 MHz. E ka fetoleloa ho 8 MHz ka ho tlama XSEL-pin fatše: De-solder R23 le solder 0 resistor pads ea R30.
Digital Communication Interface
Ka bobeli NCN5121 le NCN5130 li kenya tšebetsong mac layer ea mohlala oa OSI joalo ka ha ho bonts'itsoe ho Setšoantšo sa 10. Ba tla sebetsana le ho ngola melaetsa le ho ngola melaetsa, ho romela melaetsa, joalo-joalo ... transceiver. Transceiver e etsa bonnete ba hore ho qoba ho thulana5 ho sebetsoa ka nepo ntle le ho kenella leha e le hofe ke molaoli oa moamoheli. Sena se fokotsa haholo matsapa a ntlafatso ea software. Ho buisana le mac layer ka bobeli UART- le SPI-interface lia tšehetsoa. Lemoha hore
CSMA/CA: phihlello e ngata ea motho ea nang le kelello ka ho qoba ho thulana.
ha transceiver e sebetsa ka SPI-mode e sebetsa joalo ka monghali. Microcontroller e tlameha ho tšehetsa mokhoa oa makhoba e le hore a khone ho buisana le transceiver. Ho khetha hore na KNX-transceiver e sebetsa ka mokhoa ofe (UART kapa SPI) MODE2-pin e sebelisoa. Ha e tlameletsoe ho GND e sebelisa R32, transceiver e sebetsa ka mokhoa oa UART. Ho e tlama ho VDD1 o sebelisa R25 ho beha transceiver ho SPI-mode.
560 bahanyetsi ba sireletsa mela ea I / O e eang ho microcontroller. Ho ipapisitse le hore na li-resistors li behiloe hokae, UART kapa SPI-line li hokahane. Haeba ho hlokahala, hoa khoneha ho fetola thebe ea UART hore e be SPI, 'me ho fapana le hoo, ka ho solder/de-soldering the resistors joalokaha ho thathamisitsoe ho Lethathamo la 2.
Letlapa la 2. LIKHETHO TSA KHOTSO EA TŠEBELETSO EA TŠEBELETSO
| Puisano Sehokedi | Mohanyetsi Mounted |
| UART | R16, R17, R32 |
| SPI | R9, R11, R12, R13, R15, R25 |
Letlapa la 3. KHETHA SEKANE SA BAUD E NEPAHETSENG U SEBELISA J1/J2
| J2 | J1 | Parity Bit | Baud Rate |
| 0 | 0 | esita le | 19 bps |
| 0 | 1 | esita le | 38 bps |
| 1 | 0 | ha ho letho | 19 bps |
| 1 | 1 | ha ho letho | 38 bps |
Ho khetha The Baud Rate
Jumpers J1 le J2 li lumella tlhophiso e bonolo ea sekhahla sa baud le tekano. Sena se sebelisoa feela ka UART-mode. Ho SPI-mode, lebelo la puisano le behiloe ho 500 kbps.
Ho etsa hore puisano ea UART e be matla le ho feta, hoa khoneha ho etsa hore phetiso ea karolo e lekanang le e 'ngoe le e 'ngoe ea data. Bakeng sa litlhophiso tse felletseng, sheba sekirini sa silika thebe kapa ho Tafole ea 3.
Analog Communication Interface
Transceiver ea NCN5110 ha e na ts'ebetso ea dijithale, e sebelisa feela karolo ea 'mele ea mofuta oa OSI. Ka bobeli TXD- le RXD-line li hokahane ka kotloloho ho KNX-transmitter/receiver.
Ho hula TXD holimo ho tla etsa hore transceiver e theohe molumo oa besetage joalo ka ha ho bonts'itsoe ho Setšoantšo sa 11. Hang ha mohala oa ho fetisa o huleloa tlaase hape, transceiver e tla kenya molumo oa ho lekana ka beseng. Nako ea bese voltage lula ka
palo ea Vact ka tlase ho VDC, e khethoa ke microcontroller. Ka lebaka leo microcontroller e boetse e ikarabella bakeng sa ho lemoha le ho qoba ho thulana. Hammoho le khouto le ho hlophisa melaetsa, ho romella mangolo a tumello, joalo-joalo ... li tlameha ho kengoa ts'ebetsong ho microcontroller, ho eketsa ho rarahana ha software.
Mohala oa RXD o tla ba holimo ha ho fumanoa molumo o sebetsang ka beseng. Ha transceiver e boetse e amohela data ka boeona e fetisitsoeng ka bese, mohala ona o tla boela o phahame nakong ea phetisetso.
Numella Interface
Nako ea likhahla tse tsamaisang NCN5110 ke nako ea bohlokoa haholo. Malapa a mang a microcontroller a na le mekhoa e khethehileng ea nako e ka sebelisoang ho hlahisa likhahla tse nepahetseng. Ho sebelisa mekhoa ena, ho ka fokotsa tšebeliso ea software ho lelapa le itseng la microcontroller.
An AND port e kopanya matšoao a tsoang ho D11 le D12. Sekema se bontšoa ho Setšoantšo sa 12. E fana ka mokhoa oa ho beha le ho hlakola letšoao la ho fetisa, ntle le tšebeliso ea li-timers tse khethehileng tse fumanehang feela malapeng a khethehileng a microcontroller.
Ho ka sebelisoa li-timers tse peli, e 'ngoe ho hlahisa moeli o nyolohang, e' ngoe e le ho hlahisa moeli o oelang. Lipontšo ka bobeli li kopantsoe ho theha lets'oao le lakatsehang la phetisetso joalo ka ha ho bonts'itsoe ho Setšoantšo sa 13.
Ka bobeli lithakhisa tsa AND port li huleloa tlase. Sena se tiisa hore nakong ea ho qala ha microcontroller, transceiver e ke ke ea fetisa.
PCB THULA TSELA
Ha u rala PCB bakeng sa KNX-transceiver ho bohlokoa ho ela hloko lintlha tse itseng tsa moralo. Mekhoa e latelang e metle e tla thusa ho ntlafatsa ts'ebetso ea EMC ea ts'ebeliso eohle. Thebe ea Arduino ke PCB ea mekhahlelo e 'meli, e nang le sefofane se seholo sa fatše karolong e ka tlaase. Sebaka se se nang letho karolong e ka holimo se tlatsitsoe ka koporo e fatše, empa sena hase sefofane sa fatše.
Lisebelisoa tsa DC-DC
Tšitiso ea motlakase e laoloa ke li-converter tsa DC-DC. Li-converter tsena li fetoha ka maqhubu a ka bang 300 kHz. Ntle le ho nahanisisa ka nepo bakeng sa sebopeho sa PCB, mesi e hlahisoang ke mahlaseli e ka fetoha taba e tebileng.
Setšoantšo sa 16 se bontša examplets'oao la inverter e tsamaisang mojaro oa capacitive. Lipina tsa PCB tse eang le tse tsoang mojaro li tla sebetsa joalo ka inductor maemong a phahameng a switjha. Tsela ea ho khutla e ka ba sebaka se tloaelehileng sa potoloho, empa sena ha se joalo kamehla!
Ha ho etsoa moralo oa PCB ke habohlokoa haholo ho ela hloko tsela ea ho khutla ea pontšo.
Boemo ba pele ho Setšoantšo sa 14 se bontša moralo o le mong oa lera. Mona lets'oao le tsela ea ho khutla li theha loop e kholo, e tla sebetsa joalo ka antenna ka maqhubu a phahameng.
Sebopeho sena se ka ntlafatsoa haholo ka ho tsamaisa lets'oao le tsela ea ho khutla haufi le tse ling. Li lokela ho tsamaisoa joalokaha eka ke para e fapaneng. Meralong e mengata ea potoloho, tsela ea ho khutla bakeng sa matšoao a mangata ke sebaka se tloaelehileng sa potoloho. Bakeng sa lipotoloho tsena ho sebelisa tse peli-kapa tse 'nè-lera PCB le ka sehloohong fatše-kapa ka hare-lera ke khetho kgothaletswa. E nolofatsa mosebetsi oa moralo 'me e nolofaletsa ho etsa litsela tse nepahetseng tsa ho khutla. Leha ho le joalo tlhokomelo e lokela ho nkoa nakong ea moralo, kaha ho bonolo ho hlokomoloha liphoso tse tloaelehileng. Setšoantšo sa 15 se bontša boemo
moo ho nang le sekotjana sefofaneng se fatshe. Mokhoa oa ho khutla hona joale o potoloha sekotjana o theha antenna ea slot. Ha e le hantle sefofane sa fatše se ka tlaase ha sea lokela ho sitisoa le ka mohla.
Setšoantšo sa 17 se bonts'a li-loops tsa hajoale bakeng sa li-converter tse peli tsa DC-DC ho thebe ea Arduino. Likarolo tsohle tse holim'a thebe li behiloe 'me li tsamaisoa ho fokotsa libaka tse ka holimo tsa loop. Ha converter ea DC-DC e bulela transistor ea eona e kaholimo, spike ea hajoale e huloa ho tsoa ho 100 nF capacitor C8 e nyane. Kaha li-spikes tsena tsa hona joale li le khutšoanyane, li tla ba le maqhubu a phahameng. Kahoo loop ea bohlokoa ka ho fetisisa, ke ea hona joale e phallang ho tloha C8 ho ea ho capacitance ea parasitic ho
VSW joalokaha ho bontšitsoe ka bofubelu. Ho boloka loop ena e le nyane haholo, C8 e tlameha ho behoa haufi ka hohle kamoo ho ka khonehang ho VIN-pin. Haeba ho khonahala, e behe haufi le eona joalo ka setšoantšong sa 18.
Ho boloka dipina tsohle ka lera ka holimo qoba litšitiso leha e le efe e ka tlaase fatše lera le ho hanyetsa / inductance ho ekeletsoa ka vias. Metsu e 'meli e bohlooho e bonts'a li-loops tse kholoanyane tse entsoeng ke converter ea DC-DC. Tsena li lokela ho bolokoa li le khutšoane ka hohle kamoo ho ka khonehang ho fokotsa likhase tse tsoang. Setšoantšo sa 18 se bonts'a moralo o nepahetseng, o sebelisitsoeng thebe, ho boloka loops tsena li le nyane.
Buffer capacitor C9 e kholoanyane e ka behoa hole le VIN-pin, ha feela ceramic capacitor C8 e behiloe haufi haholo le eona.
TVS Diode
- Ho bohlokoa ho ntlafatsa sebopeho sa Transient Voltage Suppression (TVS) diode e le ho sireletsa ka katleho transceiver khahlanong le surges. Ha surge e etsahala, diode ea TVS e tlameha ho llaamp moqtage boemong bo sa senyeng transceiver. Ho finyella sena, ho hanyetsa letoto ho lokela ho ba tlase kamoo ho ka khonehang.
- Sena se ka etsoa ka ho hokahanya KNX-ka ho toba ho diode ea TVS pele e fetisetsoa sebakeng se seng sa PCB joalokaha ho bontšitsoe setšoantšong sa 20. Sena se tiisa hore tsela ea hona joale ea TVS e na le khanyetso e tlaase ka ho fetisisa 'me ha ho na nako ea nakoana e tla phallela ho transceiver.
REA QALA
Thebe ea Arduino e tla le software ea demo e ntlafalitsoeng ke Tapko Technologies GmbH. Software e kenyelletsa mofuta oa demo oa KAIstack o tsamaisang boto ea STM32F103-NUCLEO. Software ena e na le lisebelisoa tsohle tse hlokahalang tsa software ho hokahanya le bese ea KNX mme e tla le mefuta e fapaneng ea lits'ebetso tsa demo. Mofuta oa demo oa KAIstack o ka sebelisoa ho qala ho theha software ea tloaelo ea kopo. Meeli e latelang e sebetsa ho mofuta oa demo:
- E lekanyelitsoe ho liaterese tsa lihlopha tse 16, mekhatlo e 16 le lintho tse 16 tsa puisano sebakeng sa 255.
- Lisebelisoa tsa sebopeho sa kopo li tlositsoe.
- Palo ea rout e behiloe ho zero moleng oa marang-rang, e lekanyetsa tšebeliso ea ts'ebeliso ho mola o le mong feela.
- Ha ho na ho pheta-pheta holim'a lera la lipalangoang.
- Ho ke ke ha khoneha ho fetola aterese ea motho ka mong ea sesebelisoa ka ETS.
- Ke mofuta o le mong feela o tšehetsoeng.
Lintho tse hlokahalang
Ho thathamisitsoe ka tlase ke likarolo tsohle tse hlokahalang ho theha KNX-network e nyane le NCN5100ASGEVB.
- Phepelo ea motlakase ea KNX (ho kenyeletsoa le choke).
- USB-KNX segokanyimmediamentsi sa sebolokigolo ho buisana le ETS ho PC.
- Mofuta oa demo oa ETS.
- STM32F103-NUCLEO board ho hokela thebe ho eona.
- Mofuta ofe kapa ofe oa NCN5100ASGEVB
Liphetoho tsa Hardware
Ho qala ka software ea demo, ho hlokahala thebe ea NCN5110, NCN5121 kapa NCN5130 Arduino hammoho le boto ea STM32F103-NUCLEO. E le ho etsa hore software e sebetse ho microcontroller, ho hlokahala liphetoho tse 'maloa tsa hardware. Ho finyella litlhoko tsa nako ea ho buisana ka bese ea KNX, hoa hlokahala ho ba le oache e nepahetseng ho feta e fanoeng ke RC-oscillator ea ka hare ea microcontroller. Ho fanoe ka likhetho tse peli ka tlase.
Ho beha Crystal
- Beha kristale mokokotlong oa X3 botong ea Nucleo.
- kristale ena e tlameha ho ba le maqhubu a 16 MHz. Bakeng sa boleng bo khothalelitsoeng ba li-capacitor tsa C33/C34, bua ka database ea kristale.
- Kristale e ntle ke 9B-16.000MEEJ-B, e hlokang li-capacitor tsa 18 pF.
Ho etsa hore kristale e sebetse botong ea Nucleo ho hlokahala tlhophiso e latelang (Litšoantšo tsa 21 le 22):
- Sebaka sa 0 bahanyetsi ka R35 le R37.
- Solder the loading capacitor ho C33 le C34.
- Tlosa tse 0 resistor ho SB50.
- Rekisa kristale ho X3.
Sebelisa Oache ea Kantle
Khetho ea bobeli ke ho sebelisa oache e kantle. Sebelisa XCLK-output ea KNX-transceiver e le ho kenya oache bakeng sa microcontroller. Ka ho tlama XCLKC-pin e phahameng / e tlase maqhubu a oache a 16 MHz kapa 8 MHz e ka khethoa. Ka kamehla ho thebe ea Arduino, XCLKC-pin e huloa holimo, ho bolelang hore letšoao la oache la 16 MHz le teng ho XCLK-pin. Mokhoa ona o na le advantage hore kopo e feletseng e hloka kristale e le 'ngoe feela.
Ho sebelisa XCLK-output e le lets'oao la oache, ho hlokahala tlhophiso e latelang:
- Beha 0 resistor ho SB55.
- Tlosa tse 0 resistor ho tloha SB50.
- Hokela XCLK-pin ho thebe ea Arduino ho penya 29 ea CN7 boto ea Nucleo. Etsa sena ka terata e khuts'oane ka hohle kamoo ho ka khonehang.
UART Puisano
- Ka holim'a boto ea Nucleo, sebopeho sa UART2 se sebelisoa kamehla ho buisana le ST-LINK e ka holim'a board.
- Sena se bolela hore ha ho khonehe ho sebelisa D0 le D1 lihloohong tsa Arduino bakeng sa puisano ea UART, kaha ha li kopane.
Ho nolofalletsa puisano ea UART lihloohong tsa Arduino etsa mehato e latelang (Litšoantšo tsa 21 le 22):
- Tlosa tse 0 bahanyetsi ho tloha SB13 le SB14.
- Thaba ea 0 resistors ho SB62 le SB63.
Mehato ena e tla tima puisano lipakeng tsa microcontroller le ST-LINK. Joale ha ho sa khoneha ho sebelisa Virtual COM-port ho boto ea Nucleo. Ho tsoela pele ho sebelisa Virtual COM-port, hokela peripheral e 'ngoe ea UART ho ST-LINK. UART3 ke mokhethoa ea ka sebelisoang ka ho hokahanya likhoele tse peli ka tsela e latelang:
- E hoketsoe phini ea 1 ea CN7 (PC10-USART3_TX) ho phini ea RX ho CN3.
- E hoketsoe pin 2 ea CN7 (PC11-USART3_RX) ho TX pin ho CN3.
Ho theha marang-rang
Hang ha boto ea STM32F103-NUCLEO e se e loketse, marang-rang a manyenyane a ka thehoa ho qala ka NCN5100ASGEVB.
Matla a ho Hokela
Ho na le likhetho tse 'maloa tsa ho matlafatsa boto ea Nucleo. Sheba Karolo ea Matla bakeng sa litlhophiso tsohle tse ka khonehang. Ho qala, tlosa jumpers J10 le J11 ho tloha Arduino thebe 'me u behe JP5 ho Nucleo sebakeng sa U5V. Ka tsela ena microcontroller e tla tsamaisoa ho tloha boema-kepe ba USB ha KNX-transceiver e tsamaisoa ho tsoa ho bese ea KNX. Ho matlafatsa tharollo e feletseng ho tloha KNX-bese, beha J10 holim'a thebe ea Arduino le JP5 sebakeng sa E5V ho Nucleo.
UART Puisano
Software ea demo e tsoang ho Tapko e buisana le transceiver ka 19.2 kb/s e sebelisa tekanyo e lekanang. Beha J1 le J2 maemong a '0'-ho khetha lebelo le nepahetseng la puisano.
Ho aha Marang-rang
Tlhophiso e fokolang ea marang-rang e na le motlakase oa KNX, KNX USB-interface le NCN5100ASGEVB. Setupo sena se hlahisoa ho Setšoantšo sa 23. KNX USB-interface e sebelisetsoa ho lokisa NCN5100ASGEVB ka ETS le ho romela le ho amohela melaetsa. Kamora ho theha marang-rang, hokahanya USB e tsoang ho KNX USB-interface le Nucleo ho PC. Ho seta lisebelisoa tsa 'mele hona joale ho felile.
Ho kenya Software
Software ea demo ea microcontroller e ka fumanoa ho ON Semiconductor websebaka [5]. Khoasolla software, e lokolle, 'me u kenye mochini oa ho kenya. Motho ea kenyang o tla qala ka ho botsa hore na o kenya software ho lifoldara life. Foldara ea pele e tla ba le KAIstack, moqapi, software examples le litokomane. Foldareng ea bobeli ea ho kenya, lisebelisoa tse ling tsa tlatsetso le litokomane tsa KAIstack li kentsoe.
Ka mor'a moo, installer e fana ka khetho ea ho khetha hore na ke likarolo life tseo u lokelang ho li kenya. Ho khothalletsoa ho tlohela ntho e 'ngoe le e' ngoe e khethiloeng. Ha o tobetsa E latelang, ho fanoe ka kakaretso ea se tla kenngoa.
Kenya software ebe u bula foldara ea ho kenya moo KAIstack e kentsoeng. Sebopeho sa foldara se tla tšoana le se bontšitsoeng ho Setšoantšo sa 27. Ho appl_example foldara, tse ngata examplikarolo tsa mananeo a kopo li ka fumanoa. Sheba litokomane tse kenyellelitsoeng le ho kenya mokhoa oa ho fetola software examples ho litlhoko tsa hau.
Ho aha le ho Loading The Software
Sebopeho sa foldara ea ts'ebeliso ea pele example 1in1out 07B0 e bontšoa ho Setšoantšo sa 28.
Lifoldara tse peli tse bitsoang dummy le tmp li na le tsa nakoana files hlokahala ho bokella lenaneo. Tsena files e ka hlokomolohuoa. Foldara ea ETS_DB e na le morero oa ETS, o tla sebelisoa hamorao ho lokisa NCN5100ASGEVB. Sephutheli se bitsoang 1_IN_OUT_07B0 se na le tsohle fileHoa hlokahala ho qala sesebelisoa sa moetsi oa KNX. Li ka sebelisoa ho theha lethathamo la lethathamo la lihlahisoa, pokello ea lihlahisoa, joalo-joalo ...
Sephetho sa ho qetela filetse hlahisoang ke moqapi li behiloe ka har'a foldara ea tlhahiso. Binary e tlamehang ho kenngoa ho microcontroller e ka fumanoa moo. Mohloli o khethehileng oa lenaneo la kopo le sehlooho files li fumaneha foldareng ea src. A file e bitsoang project.h e na le litlhophiso tsohle tse ikhethileng tsa projeke. Merero ena kaofela e hlophisitsoe ho sebelisoa moqapi oa ARM KEIL. Hoa khoneha ho bula example merero ho KEIL µVision IDE. E hlokahalang files li fumaneha foldareng ea sebaka sa mosebetsi. Ho fumana lintlha tse ling, sheba litokomane tse kenyellelitsoeng le ho kenya. Qetellong ho na le lihlopha tse peli filee kenyelelitsoe foldareng.
Tsena li ka sebelisoa ho haha le ho tsosolosa kopo. Ho qala ka tlhophiso e hahiloeng pele, e 'ngoe ea exampmerero e tlameha ho kenngoa ka har'a microcontroller. Kopanya 1in1out_07B0 example ka ho phethahatsa sehlopha sa rebuild.cmd file. Fesetere ea litaelo e tla hlaha e bonts'a tsoelo-pele ea ts'ebetso ea ho bokella. E tla hlahisa molaetsa, joalo ka ha ho bonts'itsoe ho Setšoantšo sa 29 hang ha pokello e felile. Hona joale foldara ea tlhahiso e na le .hex file, e ka kenngoa ho microcontroller.
Ho hlophisa microcontroller, sesebelisoa sa STM32CubeProgrammer se sebelisoa. Bula lenaneo ka mor'a ho kopitsa le ho kenya phetolelo ea morao-rao. Ka sesebelisoa tobetsa Open File ebe u khetha e hlahisitsoeng .hex file. Ha e se e kentsoe sesebelisoa, tobetsa konopo ea Khoasolla ho e kenya ho microcontroller. Ho rialo fensetere File jarolla ka ho feletseng e lokela ho hlaha, joalokaha ho bontšitsoe Setšoantšo sa 30. Hona joale KNX-sesebelisoa e se e loketse 'me marang-rang a ka lokisoa.
Kamore e ke ke ea e-ba teng ka boeona 'me e tlameha ho etsoa ka har'a mohaho. Ho theha moaho, tobetsa lentsoe Mehaho ebe o Eketsa Mehaho. Hang ha moaho o thehiloe, tobetsa ho eona ka ho le letona ebe u khetha Eketsa → Likamore ho theha kamore. Ho abela NCN5100ASGEVB phaposing e sa tsoa etsoa, tobetsa ho Ha e fuoe foldara ea kamore ebe o hulela sesebelisoa ka phapusing. Ka mor'a hore sesebelisoa se hokahane le kamore, aterese ea motho ka mong e tlameha ho abeloa ho eona.
Aterese ea motho ka mong e na le sebopeho se tsitsitseng, 'me e khethoa ka tsela eo e bonahatsang boemo ba eona marang-rang. E sebelisoa feela bakeng sa ho hlophisa sesebelisoa. Bakeng sa tlhaiso-leseling e batsi ka taba ena, sheba litokomane tsa semmuso tsa KNX [4]. Setlankana sa demo sa Tapko ha se tšehetse ho fetola aterese ea motho ka mong. Kahoo sesebelisoa se tlameha ho fuoa aterese e tsitsitseng ea motho ka mong 1.5.8 joalokaha ho bontšoa ho Setšoantšo sa 33. Tobetsa sesebelisoa ka har'a phanele ea Mehaho e le hore karolo ea Thepa e bulehe ka ho le letona. Tlas'a li-setting, aterese ea motho ka mong e ka fumanoa.
Hona joale liaterese tsa lihlopha li tlameha ho abeloa e le hore sesebelisoa se buisane ka bese. Sheba litokomane tsa molao tsa KNX [4] bakeng sa boitsebiso bo eketsehileng mabapi le hore na mokhoa oa puisano o nang le liaterese tsa lihlopha o sebetsa joang. Tobetsa sesebelisoa se phaneleng ea Meaho 'me u ee ho "Lihlopha tsa Lintho" tab, joalo ka ha ho bonts'itsoe ho Setšoantšo sa 34. E tla bonts'a lintho tsohle tsa sehlopha tse tšehetsoeng le liaterese tsa sehlopha tse abetsoeng ho tsona. Liaterese tsa lihlopha tse abetsoeng li tla be li se na letho.
Ho abela sehlopha se itseng aterese ea sehlopha, tobetsa ka ho le letona ho sona ebe u khetha Link with…. Ho tla hlaha fensetere joalokaha ho bontšitsoe setšoantšong sa 35. Fesetereng ena, khetha Ncha. Tabeng ena, ho ka etsoa aterese e ncha ea sehlopha e tla abeloa ntho ea sehlopha hang-hang. Abela sehlopha aterese 0/0/2 ho ntho e nyenyane ea sehlopha le 0/0/1 ho ntho ea sehlopha sa switjha. Ba fe bobeli mabitso a loketseng. Ntho ea sehlopha sa switjha e sebelisoa ho romella boleng bo fokolang beseng nako le nako ha konopo ea SW3 e tobetsoa. Ntho e nyenyane ea sehlopha e sebelisetsoa ho laola LED3 holim'a thebe.
Hoa khoneha ho review le ho lokisa liaterese/mabitso a sehlopha phanele ea Liaterese tsa Sehlopha (Sebaka sa Mosebetsi → Bula Phanele e Ncha).
Hona joale morero o feletseng o hlophisitsoe 'me o lokela ho shebahala joaloka Setšoantšo sa 34. Hona joale tlhophiso ena e ka kenngoa ho NCN5100ASGEVB. Etsa bonnete ba hore sebopeho sa USB-KNX se hokahane le PC. Tobetsa ka ho le letona sesebelisoa ho ETS ebe u khetha Khoasolla → Khoasolla ka botlalo.
ETS joale e tla kopa ho tobetsa konopo ea lenaneo ho NCN5100ASGEVB. E ka fumanoa ka lehlakoreng le ka tlaase le letšehali la thebe. Kamora ho tobetsa konopo, LED e kaholimo e tla khantša. Joale ETS e tla qala ts'ebetso ea ho jarolla. Hang ha download e felile, bula phanele ea Diagnostics ka ho tobetsa konopo ea Diagnostics bareng ea menyu e holimo. Ka phanele ena hoa khoneha ho beha leihlo se etsahalang marang-rang le ho laola marang-rang ka sebopeho sa USB-KNX. Tobetsa konopo ea Qala ho qala ho beha leihlo marang-rang.
Joale nako le nako ha konopo ea SW3 thebe e hatelloa molaetsa o romelloa beseng ke NCN5100ASGEVB. Phanele ea Diagnostics e bonts'a hore na ke mang ea romellang molaetsa, aterese ea sehlopha e rometsoeng le boleng bofe. Boleng bo tlameha ho fetoha lipakeng tsa On le Off nako le nako ha konopo e tobetsoa.
Hoa khoneha ho romella melaetsa ka bese ka phanele ea Diagnostics ho laola e 'ngoe ea li-LED tse thebeng. Lebaleng la Aterese ea Sehlopha kenya 0/0/2. Ha o tobetsa konopo ea Bala, sebopeho sa USB-KNX se romela kopo ea ho bala ka bese bakeng sa ntho ea sehlopha 0/0/2. NCN5100ASGEVB e tla arabela ka boemo ba hona joale ba LED3, e leng Off. Sebakeng sa Bohlokoa kenya 1. Ha konopo ea Ngola e hatelloa, sebopeho sa USB-KNX se romela ntho ea sehlopha 0/0/2 beseng e nang le boleng ba On. LED3 ho thebe joale e lokela ho khantša. Ha o tobetsa konopo ea Bala hape sesebelisoa se tla arabela ka On.
BIBLIOGRAFI
Litekanyetso
- KNX Standard v2.1 − Litlhoko le Liteko tsa Hardware tsa KNX - Karolo ea 4−1: Litlhoko tsa Polokeho le Tikoloho - Kakaretso. KNX, 2013.
- KNX Standard v2.1 − Teko ea Tsamaiso ea Tsamaiso - Karolo ea 8−2-2: Liteko tsa Merero e Itšetlehileng ka Bohareng - Liteko tsa TP1 tsa Physical and Link Layer. KNX, 2013.
Marang-rang
- Mokhatlo oa KNX. 2020, e fihletsoe ka la 28 Pherekhong 2020. URL: https://www.knx.org.
- Litsi tsa Koetliso tsa KNX. 2020, e fihletsoe ka la 28 Pherekhong 2020. URL: https://www.knx.org/knx−en/for−professionals/community/training−centres/index.php.
- Litharollo tsa khokahanyo ea marang-rang. 2020, e fihletsoe ka la 28 Pherekhong 2020. url: https://www.onsemi.com/PowerSolutions/segment.do?method=subSolution&segmentId=IoT&solutionId=19116&subSolutionId=19126.
SEHLOMATHISO A
SEHLOMATHISO A − MICROCONTROLLER NET LIST NCN5100AS-1
Lethathamo la 4. MICROCONTROLLER PINN LETHATA
| Pina Lihlooho tsa Arduino | E hokahane le | Mosebetsi | Tataiso ea Pin ea MCU |
| D0/RX | SDO/TXD | UART fumana mohala | IN |
| D1/TX | SDI/RXD | Mokhoa oa ho fetisa UART | TSOA |
| D2 | SAVEB | Boloka sesupo sa data | IN |
| D3/PWM | LED5 | CH2 konopo e khubelu ea LED | TSOA |
| D4 | SW4 | Konopo ea holimo CH2 | IN |
| D5/PWM | LED3 | CH2 LED ea konopo e mosehla | TSOA |
| D6/PWM | LED2 | CH1 Botala tlase konopo ea LED | TSOA |
| D7 | SW1 | Konopo e tlase CH1 | IN |
| D8 | SW3 | Konopo ea holimo CH1 | IN |
| D9/PWM | LED4 | CH1 Orange holimo konopo ea LED | TSOA |
| D10/CS | CSB/UC1 | SPI chip khetha | IN |
| D11/MOSI | SDO/TXD | SPI MOSI | IN |
| D12/MISO | SDI/RXD | SPI MISO | TSOA |
| D13/SCK | SCK/UC2 | Oache ea SPI | IN |
| A0 | ANAOUT | Lihlahisoa tsa Analog multiplexer | IN (analoge) |
| A1 | SW2 | Konopo e tlase CH2 | IN |
| A2 | TREQ | Kopo ea phetisetso | TSOA |
| A3 | LED6 | Lenaneo la LED | TSOA |
| A4 | S1 | Konopo ea ho etsa mananeo | IN |
SEHLOMATHISO B
SEHLOMATHISO B − MICROCONTROLLER NET LIST NCN5100AS-2
Lethathamo la 5. MICROCONTROLLER PINN LETHATA
| Pina Lihlooho tsa Arduino | E hokahane le | Mosebetsi | Tataiso ea Pin ea MCU |
| D3/PWM | LED5 | CH2 konopo e khubelu ea LED | TSOA |
| D4 | SW4 | Konopo ea holimo CH2 | IN |
| D5/PWM | LED3 | CH2 LED ea konopo e mosehla | TSOA |
| D6/PWM | LED2 | CH1 Botala tlase konopo ea LED | TSOA |
| D7 | SW1 | Konopo e tlase CH1 | IN |
| D8 | SW3 | Konopo ea holimo CH1 | IN |
| D9/PWM | LED4 | CH1 Orange holimo konopo ea LED | TSOA |
| D11 | EA-RXD2 | Lintlha tsa NCN5110 | TSOA |
| D12 | EA-RXD1 | Lintlha tsa NCN5110 | TSOA |
| A0 | TXD | Lethathamo la lintlha tsa NCN5110 | IN |
| A1 | SW2 | Konopo e tlase CH2 | IN |
| A3 | LED6 | Lenaneo la LED | TSOA |
| A4 | S1 | Konopo ea ho etsa mananeo | IN |
SEHLOMATHISO C
SEHLOMATHISO C − LENANE LA LIPALATEFO TSA TEKO
Lethathamo la 6. LIEKETSENG LITEKO
| Moetsi | Boto ea Nts'etsopele | Microcontroller |
| STMicroelectronics | NUCLEO−F103RB | Setšoantšo sa STM32F103RB |
| Cypress | CY8CKIT−044 | CY8C4247AZI−M485 |
| Waveshare | XNUCLEO−F103RB | Setšoantšo sa STM32F103RB |
SEHLOMATHISO D
SEHLOMATHISO D - NCN5130ASGEVB
Mofuta oa UART
Lethathamo la 7. LITŠOANTŠISO TSA LITŠOANTŠISO UART-VERSION
| Moqapi | Qty | Tlhaloso | Boleng | Nomoro ea Karolo |
| J1 | 1 | WR−PHD 2.54 mm THT Pin Header, 3p | 61300311121 | |
| J2 | 1 | WR−PHD 2.54 mm THT Pin Header, 3p | 61300311121 | |
| J3 | 1 | WR−PHD 2.54 mm THT Pin Header, 1p | 61300111121 | |
| J4 | 1 | Sehokelo sa Boto ho ea ho Boto, 2.54 mm,
Mabitso a 8, Mokelikeli, ka Mokoti, Mela e 1 |
SSQ−110−03−G−S | |
| J6 | 1 | Sehokelo sa Boto-to-Boto, 2.54 mm, Mabitso a 10, Mohaho, ka Mokoti, Mela e 1 | SSQ−110−03−G−S | |
| J7 | 1 | Sehokelo sa Boto ho ea ho Boto, 2.54 mm,
Mabitso a 6, Mokelikeli, ka Mokoti, Mela e 1 |
SSQ−106−03−G−S | |
| J8 | 1 | Serie 2141 − 3.50 mm Horizontal Entry Modular with Rising Cage Clamp WR−TBL, 3 pin | 691214110003 | |
| J9 | 1 | Sehokelo sa Boto ho ea ho Boto, 2.54 mm,
Mabitso a 8, Mokelikeli, ka Mokoti, Mela e 1 |
SSQ−108−03−G−S | |
| L2 | 1 | SMT Power Inductor WE−LQFS, boholo ba 4828, 220 µH, 0.4 A | 74406043221 | |
| L3 | 1 | SMT Power Inductor WE−LQFS, boholo ba 4828, 220 µH, 0.4 A | 74406043221 | |
| Q1 | 1 | N-Channel Logic Level Enhancement Mode Field Effect Transistor, 30 V, 1.7 A, −55°C to 150°C, 3-Pin SOT−3, RoHS, Tape le Reel | Tlhaloso: NDS355AN | |
| J10, j11 | 2 | WR−PHD 2.54 mm THT Pin Header, 2p | ||
| R6, R7, R8, R23, R31, R32 | 6 | Mohanyetsi | 0 Q | RC0603JR-070RL |
| C10 | 1 | Capacitor | 1µF, 50 V | Setšoantšo sa GCM21BR71H105KA03L |
| D1 | 1 | Schottky Rectifier, Singel 60 V, 1 A, DO−214AC, 2 Pins, 720 mV | 1 A / 720 mV / 60 V | SS16T3G |
| R20, R21 | 2 | Mohanyetsi | 1 Q | RC0603FR−071RL |
| LED3 | 1 | LED, Yellow, SMD, 2 mA, 2.2 V, 594 nm | 2 mA, 2.2 V, 594 nm | VLMA3100−GS08 |
| R19 | 1 | 2 (1 x 2) Position Shunt Connector
Non Insulated 0.400 in (10.16 mm) Khauta |
2 phini | D3082−05 |
| LED4 | 1 | LED, Orange, SMD, 2.4 mm, 2 mA, 1.8 V,
609 nm |
2.4 mm, 2 mA, 1.8 V,
609 nm |
Setšoantšo sa VLMO30L1M2−GS08 |
| LED2 | 1 | LED, Botala, SMD, 2.4 mm, 2 mA, 1.9 V, 575
nm |
2.4 mm, 2 mA, 1.9 V,
575 nm |
VLMMC3100−GS08 |
| C11, C12 | 2 | Capacitor | 10 µF | C3216X7R1E106K160AE |
| R2, R3, R4, R5, R26, R27, R28, R29, R37 | 9 | Mohanyetsi | 10 Q | Setšoantšo sa CRCW060310K0FKEA |
| C1, C2 | 2 | Capacitor | 10 pf | Setšoantšo sa C0402C100J5GACTU |
| SW1, SW2, SW3, SW4 | 4 | Fetoha | 12 V, 50 mA | MCDTS6−3N |
| X1 | 1 | Crystal Oscillator, 16 MHz, Low Profile SMD, 3.2 mm 2.5 mm, 30 ppm, 12.5 pF, 50 ppm, FA−238 Series | 16 MHz ho 60 MHz / Mojaro: 12.5 pF / Botsitso: 30 ppm / Mamello: 50 ppm | Q22FA23800181 FA−238 |
| R22 | 1 | Mohanyetsi | 20 Q | Setšoantšo sa CRCW060320K0FKEA |
| R10 | 1 | Mohanyetsi | 27 Q | 352027RJT |
| U1 | 1 | Transceiver bakeng sa KNX Twisted Pair Networks | 40 phini | NCN5130MNTWG |
| D2 | 1 | SMAJ40CA − TVS Diode, TRANZORB SMAJ
Series, Bidirectional, 40 V, 64.5 V, DO−214AC, 2 Pins |
40 V, 400 W | SMAJ40CA |
| C5 | 1 | Capacitor | 47 nF, 50 V | CGA3E2X7R1H473K080AA |
| C9 | 1 | Capacitor | 100µF, 35 V | Setšoantšo sa EEEFT1V101AP |
| S1 | 1 | 6.0 x 3.8 mm SMD J−Bend WS−TASV | 100 mQ, 250 V (AC) | 434 123 025 816 |
| C3, C4 | 2 | Capacitor | 100NF | CC0402KRX7R7BB104 |
| C8 | 1 | Capacitor | 100 nF, 50 V | VJ0603Y104KXACW1BC |
| C7 | 1 | Capacitor | 100 nF, 50 V | VJ0603Y104KXACW1BC |
| R18 | 1 | Mohanyetsi | 130 Q | CRCW0603130KFKEA |
| C6 | 1 | Capacitor | 220 nF, 50 V | CGA3E3X7R1H224K080AB |
| R1, R16, R17, R34 | 4 | Mohanyetsi | 560 Q | CRCW0603560RFKEA |
| LED6 | 1 | Mount Mount Chip LED, e khubelu | 0603, khubelu | KPT−1608EC |
| R33, R38 | 2 | Mohanyetsi | 680 Q | CRCW0603680RFKEA |
| R14, R35, R36 | 3 | Mohanyetsi | 750 Q | CRCW0603750RFKEA |
| J5 | 1 | Sehokelo sa banna sa WAGO 243−211 | Bophahamo: 5.75 limilimithara / bophara: 1 mm / 100 V / 6 A | 13.14.125 |
| LED1, LED5 | 2 | LED, Khubelu, 2.4 limilimithara, 636 nm, 1.8 V, 2 mA,
18 mcd |
Khubelu, 1.8 V, 2 mA | Setšoantšo sa VLMS30J1L2−GS08 |
| D3 | 1 | Surface Mount Schottky Power Rectifier | Uf = 430 mV,
Haeba = 500 mA, Ur = 30 V |
Setšoantšo sa MBR0530T1G |
Mofuta oa SPI
Lethathamo la 8. LITŠOANTŠISO SPI-VERSION
| Moqapi | Qty | Tlhaloso | Boleng | Nomoro ea Karolo |
| J3 | 1 | WR−PHD 2.54 mm THT Pin Header, 1p | 61300111121 | |
| J4 | 1 | Sehokelo sa Boto ho ea ho Boto, 2.54 mm,
Mabitso a 8, Mokelikeli, ka Mokoti, Mela e 1 |
SSQ−110−03−G−S | |
| J6 | 1 | Sehokelo sa Boto ho ea ho Boto, 2.54 mm,
Mabitso a 10, Mokelikeli, ka Mokoti, Mela e 1 |
SSQ−110−03−G−S | |
| J7 | 1 | Sehokelo sa Boto ho ea ho Boto, 2.54 mm,
Mabitso a 6, Mokelikeli, ka Mokoti, Mela e 1 |
SSQ−106−03−G−S | |
| J8 | 1 | Serie 2141 − 3.50 mm Horizontal Entry Modular with Rising Cage Clamp WR−TBL, 3 pin | 691214110003 | |
| J9 | 1 | Sehokelo sa Boto ho ea ho Boto, 2.54 mm,
Mabitso a 8, Mokelikeli, ka Mokoti, Mela e 1 |
SSQ−108−03−G−S | |
| L2 | 1 | SMT Power Inductor WE−LQFS, boholo ba 4828, 220 µH, 0.4 A | 74406043221 | |
| L3 | 1 | SMT Power Inductor WE−LQFS, boholo ba 4828, 220 µH, 0.4 A | 74406043221 | |
| Q1 | 1 | N-Channel Logic Level Enhancement Mode Field Effect Transistor, 30 V, 1.7 A, −55°C to 150°C, 3-Pin SOT−3, RoHS, Tape le Reel | Tlhaloso: NDS355AN | |
| J10, j11 | 2 | WR−PHD 2.54 mm THT Pin Header, 2p | ||
| R6, R7, R8, R23, R25, R31 | 6 | Mohanyetsi | 0 Q | RC0603JR-070RL |
| C10 | 1 | Capacitor | 1µF, 50 V | Setšoantšo sa GCM21BR71H105KA03L |
| D1 | 1 | Schottky Rectifier, Singel 60 V, 1 A, DO−214AC, 2 Pins, 720 mV | 1 A / 720 mV / 60 V | SS16T3G |
| R20, R21 | 2 | Mohanyetsi | 1 Q | RC0603FR−071RL |
| LED3 | 1 | LED, Yellow, SMD, 2 mA, 2.2 V, 594 nm | 2 mA, 2.2 V, 594 nm | VLMA3100−GS08 |
| R19 | 1 | 2 (1 x 2) Position Shunt Connector
Non−Insulated 0.400 in (10.16 mm) Khauta |
2 phini | D3082−05 |
| LED4 | 1 | LED, Orange, SMD, 2.4 mm, 2 mA, 1.8 V,
609 nm |
2.4 mm, 2 mA, 1.8 V,
609 nm |
Setšoantšo sa VLMO30L1M2−GS08 |
| LED2 | 1 | LED, Botala, SMD, 2.4 mm, 2 mA, 1.9 V,
575 nm |
2.4 mm, 2 mA, 1.9 V,
575 nm |
VLMMC3100−GS08 |
| C11, C12 | 2 | Capacitor | 10 µF | C3216X7R1E106K160AE |
| R2, R3, R26, R27, R28, R29, R37 | 7 | Mohanyetsi | 10 Q | Setšoantšo sa CRCW060310K0FKEA |
| C1, C2 | 2 | Capacitor | 10 pf | Setšoantšo sa C0402C100J5GACTU |
| SW1, SW2, SW3, SW4 | 4 | Fetoha | 12 V, 50 mA | MCDTS6−3N |
| X1 | 1 | Crystal Oscillator, 16 MHz, Low Profile SMD, 3.2 mm 2.5 mm, 30 ppm, 12.5 pF, 50 ppm, FA−238 Series | 16 MHz ho 60 MHz / Mojaro: 12.5 pF / Botsitso: 30 ppm / Mamello: 50 ppm | Q22FA23800181 FA−238 |
| R22 | 1 | Mohanyetsi | 20 Q | Setšoantšo sa CRCW060320K0FKEA |
| R10 | 1 | Mohanyetsi | 27 Q | 352027RJT |
| U1 | 1 | Transceiver bakeng sa KNX Twisted Pair Networks | 40 phini | NCN5130MNTWG |
| D2 | 1 | SMAJ40CA − TVS Diode, TRANZORB SMAJ
Series, Bidirectional, 40 V, 64.5 V, DO−214AC, 2 Pins |
40 V, 400 W | SMAJ40CA |
| C5 | 1 | Capacitor | 47 nF, 50 V | CGA3E2X7R1H473K080AA |
| C9 | 1 | Capacitor | 100µF, 35 V | Setšoantšo sa EEEFT1V101AP |
| S1 | 1 | 6.0 x 3.8 mm SMD J−Bend WS−TASV | 100 mQ, 250 V (AC) | 434 123 025 816 |
| C3, C4 | 2 | Capacitor | 100NF | CC0402KRX7R7BB104 |
| C8 | 1 | Capacitor | 100 nF, 50 V | VJ0603Y104KXACW1BC |
| C7 | 1 | Capacitor | 100 nF, 50 V | VJ0603Y104KXACW1BC |
| R18 | 1 | Mohanyetsi | 130 Q | CRCW0603130KFKEA |
| C6 | 1 | Capacitor | 220 nF, 50 V | CGA3E3X7R1H224K080AB |
| R1, R9, R11, R12, R13, R15, R34 | 7 | Mohanyetsi | 560 Q | CRCW0603560RFKEA |
| LED6 | 1 | Mount Mount Chip LED, e khubelu | 0603, khubelu | KPT−1608EC |
| R33, R38 | 2 | Mohanyetsi | 680 Q | CRCW0603680RFKEA |
| R14, R35, R36 | 3 | Mohanyetsi | 750 Q | CRCW0603750RFKEA |
| J5 | 1 | Sehokelo sa banna sa WAGO 243−211 | Bophahamo: 5.75 limilimithara / Bophara: 1 mm / 100 V / 6 A | 13.14.125 |
| LED1, LED5 | 2 | LED, Khubelu, 2.4 limilimithara, 636 nm, 1.8 V, 2 mA,
18 mcd |
Khubelu, 1.8 V, 2 mA | Setšoantšo sa VLMS30J1L2−GS08 |
| D3 | 1 | Surface Mount Schottky Power Rectifier | Uf = 430 mV,
Haeba = 500 mA, Ur = 30 V |
Setšoantšo sa MBR0530T1G |
SEHLOMATHISO E
SEHLOMATHISO E - NCN5121ASGEVB
Mofuta oa UART
Lethathamo la 9: LITŠOANTŠISO TSA LITŠOANTŠISO UART-VERSION
| Moqapi | Qty | Tlhaloso | Boleng | Nomoro ea Karolo |
| J1 | 1 | WR−PHD 2.54 mm THT Pin Header, 3p | 61300311121 | |
| J2 | 1 | WR−PHD 2.54 mm THT Pin Header, 3p | 61300311121 | |
| J3 | 1 | WR−PHD 2.54 mm THT Pin Header, 1p | 61300111121 | |
| J4 | 1 | Sehokelo sa Boto ho ea ho Boto, 2.54 mm,
Mabitso a 8, Mokelikeli, ka Mokoti, Mela e 1 |
SSQ−110−03−G−S | |
| J6 | 1 | Sehokelo sa Boto-to-Boto, 2.54 mm, Mabitso a 10, Mohaho, ka Mokoti, Mela e 1 | SSQ−110−03−G−S | |
| J7 | 1 | Sehokelo sa Boto ho ea ho Boto, 2.54 mm,
Mabitso a 6, Mokelikeli, ka Mokoti, Mela e 1 |
SSQ−106−03−G−S | |
| J8 | 1 | Serie 2141 − 3.50 mm Horizontal Entry Modular with Rising Cage Clamp WR−TBL, 3 pin | 691214110003 | |
| J9 | 1 | Sehokelo sa Boto ho ea ho Boto, 2.54 mm,
Mabitso a 8, Mokelikeli, ka Mokoti, Mela e 1 |
SSQ−108−03−G−S | |
| L2 | 1 | SMT Power Inductor WE−LQFS, boholo ba 4828, 220 µH, 0.4 A | 74406043221 | |
| L3 | 1 | SMT Power Inductor WE−LQFS, boholo ba 4828, 220 µH, 0.4 A | 74406043221 | |
| Q1 | 1 | N-Channel Logic Level Enhancement Mode Field Effect Transistor, 30 V, 1.7 A, −55°C to 150°C, 3-Pin SOT−3, RoHS, Tape le Reel | Tlhaloso: NDS355AN | |
| J10, j11 | 2 | WR−PHD 2.54 mm THT Pin Header, 2p | ||
| R3, R6, R7, R8, R23, R31, R32 | 7 | Mohanyetsi | 0 Q | CRCW06030000Z0EA, RC0603JR−070RL |
| C10 | 1 | Capacitor | 1µF, 50 V | Setšoantšo sa GCM21BR71H105KA03L |
| D1 | 1 | Schottky Rectifier, Singel 60 V, 1 A, DO−214AC, 2 Pins, 720 mV | 1 A / 720 mV / 60 V | SS16T3G |
| R20, R21 | 2 | Mohanyetsi | 1 Q | RC0603FR−071RL |
| LED3 | 1 | LED, Yellow, SMD, 2 mA, 2.2 V, 594 nm | 2 mA, 2.2 V, 594 nm | VLMA3100−GS08 |
| R19 | 1 | 2 (1 x 2) Position Shunt Connector
Non Insulated 0.400 in (10.16 mm) Khauta |
2 phini | D3082−05 |
| LED4 | 1 | LED, Orange, SMD, 2.4 mm, 2 mA, 1.8 V,
609 nm |
2.4 mm, 2 mA, 1.8 V,
609 nm |
Setšoantšo sa VLMO30L1M2−GS08 |
| LED2 | 1 | LED, Botala, SMD, 2.4 mm, 2 mA, 1.9 V,
575 nm |
2.4 mm, 2 mA, 1.9 V,
575 nm |
VLMMC3100−GS08 |
| C11, C12 | 2 | Capacitor | 10 µF | C3216X7R1E106K160AE |
| R2, R4, R5, R26, R27, R28, R29, R37 | 8 | Mohanyetsi | 10 Q | Setšoantšo sa CRCW060310K0FKEA |
| C1, C2 | 2 | Capacitor | 10 pf | Setšoantšo sa C0402C100J5GACTU |
| SW1, SW2, SW3, SW4 | 4 | Fetoha | 12 V, 50 mA | MCDTS6−3N |
| X1 | 1 | 16 MHz ho 60 MHz / Mojaro: 12.5 pF / Botsitso: 30 ppm / Mamello: 50 ppm | Q22FA23800181 FA−238 | |
| R22 | 1 | Mohanyetsi | 20 Q | Setšoantšo sa CRCW060320K0FKEA |
| R10 | 1 | Mohanyetsi | 27 Q | 352027RJT |
| U1 | 1 | Transceiver bakeng sa KNX Twisted Pair Networks | 40 phini | NCN5121MNTWG |
| D2 | 1 | SMAJ40CA − TVS Diode, TRANZORB SMAJ
Series, Bidirectional, 40 V, 64.5 V, DO−214AC, 2 Pins |
40 V, 400 W | SMAJ40CA |
| C5 | 1 | Capacitor | 47 nF, 50 V | CGA3E2X7R1H473K080AA |
| C9 | 1 | Capacitor | 100µF, 35 V | Setšoantšo sa EEEFT1V101AP |
| S1 | 1 | 6.0 x 3.8 mm SMD J−Bend WS−TASV | 100 mQ, 250 V (AC) | 434 123 025 816 |
| C3, C4 | 2 | Capacitor | 100NF | CC0402KRX7R7BB104 |
| C8 | 1 | Capacitor | 100 nF, 50 V | VJ0603Y104KXACW1BC |
| C7 | 1 | Capacitor | 100 nF, 50 V | VJ0603Y104KXACW1BC |
| R18 | 1 | Mohanyetsi | 130 Q | CRCW0603130KFKEA |
| C6 | 1 | Capacitor | 220 nF, 50 V | CGA3E3X7R1H224K080AB |
| R1, R16, R17, R34 | 4 | Mohanyetsi | 560 Q | CRCW0603560RFKEA |
| LED6 | 1 | Mount Mount Chip LED, e khubelu | 0603, khubelu | KPT−1608EC |
| R33, R38 | 2 | Mohanyetsi | 680 Q | CRCW0603680RFKEA |
| R14, R35, R36 | 3 | Mohanyetsi | 750 Q | CRCW0603750RFKEA |
| J5 | 1 | Sehokelo sa banna sa WAGO 243−211 | Bophahamo: 5.75 limilimithara / Bophara: 1 mm / 100 V / 6 A | 13.14.125 |
| LED1, LED5 | 2 | LED, Khubelu, 2.4 limilimithara, 636 nm, 1.8 V, 2 mA,
18 mcd |
Khubelu, 1.8 V, 2 mA | Setšoantšo sa VLMS30J1L2−GS08 |
| D3 | 1 | Surface Mount Schottky Power Rectifier | Uf = 430 mV,
Haeba = 500 mA, Ur = 30 V |
Setšoantšo sa MBR0530T1G |
Mofuta oa SPI
Lethathamo la 10: LITŠOANTŠISO SPI-VERSION
| Moqapi | Qty | Tlhaloso | Boleng | Nomoro ea Karolo |
| J3 | 1 | WR−PHD 2.54 mm THT Pin Header, 1p | 61300111121 | |
| J4 | 1 | Sehokelo sa Boto ho ea ho Boto, 2.54 mm,
Mabitso a 8, Mokelikeli, ka Mokoti, Mela e 1 |
SSQ−110−03−G−S | |
| J6 | 1 | Sehokelo sa Boto-to-Boto, 2.54 mm, Mabitso a 10, Mohaho, ka Mokoti, Mela e 1 | SSQ−110−03−G−S | |
| J7 | 1 | Sehokelo sa Boto ho ea ho Boto, 2.54 mm,
Mabitso a 6, Mokelikeli, ka Mokoti, Mela e 1 |
SSQ−106−03−G−S | |
| J8 | 1 | Serie 2141 − 3.50 mm Horizontal Entry Modular with Rising Cage Clamp WR−TBL, 3 pin | 691214110003 | |
| J9 | 1 | Sehokelo sa Boto ho ea ho Boto, 2.54 mm,
Mabitso a 8, Mokelikeli, ka Mokoti, Mela e 1 |
SSQ−108−03−G−S | |
| L2 | 1 | SMT Power Inductor WE−LQFS, boholo ba 4828, 220 µH, 0.4 A | 74406043221 | |
| L3 | 1 | SMT Power Inductor WE−LQFS, boholo ba 4828,
2−20 µH, 0.4 A |
74406043221 | |
| Q1 | 1 | Ntlafatso ea Boemo ba Monahano ba N−Channel
Mode Field Effect Transistor, 30 V, 1.7 A, 55°C ho isa ho 150°C, 3-Pin SOT−3, RoHS, Theipi le Reel |
Tlhaloso: NDS355AN | |
| J10, j11 | 2 | WR−PHD 2.54 mm THT Sehlooho sa Pin, | ||
| R3, R6, R7, R8,
R23, R25, R31 |
7 | Mohanyetsi | 0 Q | CRCW06030000Z0EA,
RC0603JR-070RL |
| C10 | 1 | Capacitor | 1µF, 50 V | Setšoantšo sa GCM21BR71H105KA03L |
| D1 | 1 | Schottky Rectifier, Singel 60 V, 1 A, DO−214AC, 2 Pins, 720 mV | 1 A / 720 mV / 60 V | SS16T3G |
| R20, R21 | 2 | Mohanyetsi | 1 Q | RC0603FR−071RL |
| LED3 | 1 | LED, Yellow, SMD, 2 mA, 2.2 V, 594 nm | 2 mA, 2.2 V, 594 nm | VLMA3100−GS08 |
| R19 | 1 | 2 (1 x 2) Position Shunt Connector
Khauta e sa kenngoeng ka 0.400in (10.16 mm). |
2 phini | D3082−05 |
| LED4 | 1 | LED, Orange, SMD, 2.4 mm, 2 mA, 1.8 V,
609 nm |
2.4 limilimithara, 2 mA,
1.8 V, 609 nm |
Setšoantšo sa VLMO30L1M2−GS08 |
| LED2 | 1 | LED, Botala, SMD, 2.4 mm, 2 mA, 1.9 V,
575 nm |
2.4 limilimithara, 2 mA,
1.9 V, 575 nm |
VLMMC3100−GS08 |
| C11, C12 | 2 | Capacitor | 10 µF | C3216X7R1E106K160AE |
| R2, R26, R27, R28, R29, R37 | 6 | Mohanyetsi | 10 Q | Setšoantšo sa CRCW060310K0FKEA |
| C1, C2 | 2 | Capacitor | 10 pf | Setšoantšo sa C0402C100J5GACTU |
| SW1, SW2, SW3, | 4 | Fetoha | 12 V, 50 mA | MCDTS6−3N |
| SW4 X1 | 1 | 16 MHz ho 60 Mhz / Mojaro: 12.5 pF / Botsitso: 30 ppm / Mamello: 50 ppm | Q22FA23800181 FA−238 | |
| R22 | 1 | Mohanyetsi | 20 Q | Setšoantšo sa CRCW060320K0FKEA |
| R10 | 1 | Mohanyetsi | 27 Q | 352027RJT |
| U1 | 1 | Transceiver bakeng sa KNX Twisted Pair Networks | 40 phini | NCN5121MNTWG |
| D2 | 1 | SMAJ40CA − TVS Diode, TRANSZORB SMAJ Series,
Bidirectional, 40 V, 64.5 V, DO−214AC, 2 Pins |
40 V, 400 W | SMAJ40CA |
| C5 | 1 | Capacitor | 47 nF, 50 V | CGA3E2X7R1H473K080AA |
| C9 | 1 | Capacitor | 100µF, 35 V | Setšoantšo sa EEEFT1V101AP |
| S1 | 1 | 6.0 x 3.8 mm SMD J−Bend WS−TASV | 100 mQ, 250 V (AC) | 434 123 025 816 |
| C3, C4 | 2 | Capacitor | 100NF | CC0402KRX7R7BB104 |
| C8 | 1 | Capacitor | 100 nF, 50 V | VJ0603Y104KXACW1BC |
| C7 | 1 | Capacitor | 100 nF, 50 V | VJ0603Y104KXACW1BC |
| R18 | 1 | Mohanyetsi | 130 Q | CRCW0603130KFKEA |
| C6 | 1 | Capacitor | 220 nF, 50 V | CGA3E3X7R1H224K080AB |
| R1, R9, R11, R12, R13, R15, R34 | 7 | Mohanyetsi | 560 Q | CRCW0603560RFKEA |
| LED6 | 1 | Mount Mount Chip LED, e khubelu | 0603, khubelu | KPT−1608EC |
| R33, R38 | 2 | Mohanyetsi | 680 Q | CRCW0603680RFKEA |
| R14, R35, R36 | 3 | Mohanyetsi | 750 Q | CRCW0603750RFKEA |
| J5 | 1 | Sehokelo sa banna sa WAGO 243−211 | Bophahamo: 5.75 limilimithara / Bophara: 1 mm / 100 V / 6 A | 13.14.125 |
| LED1, LED5 | 2 | LED, Khubelu, 2.4 limilimithara, 636 nm, 1.8 V, 2 mA,
18 mcd |
Khubelu, 1.8 V, 2 mA | Setšoantšo sa VLMS30J1L2−GS08 |
| D3 | 1 | Surface Mount Schottky Power Rectifier | Uf = 430 mV,
Haeba = 500 mA, Ur = 30 V |
Setšoantšo sa MBR0530T1G |
SEHLOMATHISO F
SEHLOMATHISO F − NCN5110ASGEVB SCHEMATIC (KGETHO E FULL)
Khetho e Feletseng
Lethathamo la 11: LITŠOANTŠISO TSE KHOLO
| Moqapi | Qty | Tlhaloso | Boleng | Nomoro ea Karolo |
| J1 | 1 | WR−PHD 2.54 mm THT Pin Header, 03p | 61300311121 | |
| J4 | 1 | Sehokelo sa Boto ho ea ho Boto, 2.54 mm,
Mabitso a 8, Mokelikeli, ka Mokoti, Mela e 1 |
SSQ−110−03−G−S | |
| J6 | 1 | Sehokelo sa Boto-to-Boto, 2.54 mm, Mabitso a 10, Mohaho, ka Mokoti, Mela e 1 | SSQ−110−03−G−S | |
| J7 | 1 | Sehokelo sa Boto ho ea ho Boto, 2.54 mm,
Mabitso a 6, Mokelikeli, ka Mokoti, Mela e 1 |
SSQ−106−03−G−S | |
| J8 | 1 | Serie 2141 − 3.50 mm Horizontal Entry Modular with Rising Cage Clamp WR−TBL, 3 pin | ||
| J9 | 1 | Sehokelo sa Boto ho ea ho Boto, 2.54 mm,
Mabitso a 8, Mokelikeli, ka Mokoti, Mela e 1 |
SSQ−108−03−G−S | |
| L2 | 1 | SMT Power Inductor WE−LQFS, boholo ba 4828, 220 µH, 0.4 A | ||
| L3 | 1 | SMT Power Inductor WE−LQFS, boholo ba 4828,
2−20 µH, 0.4 A |
||
| Q1 | 1 | Mokhoa oa Ntlafatso ea Boemo ba Monahano oa N-Channel
Field Effect Transistor, 30 V, 1.7 A, 55°C ho isa ho 150°C, 3-Pin SOT−3, RoHS, Theipi le Reel |
||
| U2 | 1 | Kenyo e le 'Ngoe 2 LE Heke | MC74HC1G08DTT1G | |
| J10, j11 | 2 | WR−PHD 2.54 mm THT Pin Header, 2p | ||
| R6, R13, R15 | 3 | Mohanyetsi | 0 Q | |
| C10 | 1 | Capacitor | 1µF, 50 V | |
| D1 | 1 | Schottky Rectifier, Singel 60 V, 1 A, | 1 A / 720 mV / 60 V | SS16T3G |
| R20, R21 | 2 | Mohanyetsi | 1 Q | |
| LED3 | 1 | LED, Yellow, SMD, 2 mA, 2.2 V, 594 nm | 2 mA, 2.2 V, 594 nm | VLMA3100−GS08 |
| R19 | 1 | 2 (1 x 2) Position Shunt Connector | 2 phini | D3082−05 |
| LED4 | 1 | LED, Orange, SMD, 2.4 mm, 2 mA, 1.8 V,
609 nm |
2.4 mm, 2 mA, 1.8 V,
609 nm |
Setšoantšo sa VLMO30L1M2−GS08 |
| LED2 | 1 | LED, Botala, SMD, 2.4 mm, 2 mA, 1.9 V,
575 nm |
2.4 mm, 2 mA, 1.9 V,
575 nm |
VLMMC3100−GS08 |
| C11, C12 | 2 | Capacitor | 10 µF | |
| R2, R3, R7, R8, R26, R27, R28, R29, R37 | 9 | Mohanyetsi | 10 Q | |
| SW1, SW2, SW3, SW4 | 4 | Fetoha | 12 V, 50 mA | MCDTS6−3N |
| R22 | 1 | Mohanyetsi | 20 Q | |
| R10 | 1 | Mohanyetsi | 27 Q | |
| U1 | 1 | Transceiver bakeng sa KNX Twisted Pair Networks | 40 phini | NCN5110 |
| D2 | 1 | SMAJ40CA − TVS Diode, TRANZORB
SMAJ Series, Bidirectional, 40 V, 64.5 V, DO−214AC, 2 Pins |
40 V, 400 W | SMAJ40CA |
| C9 | 1 | Capacitor | 47µF, 35 V | |
| C5 | 1 | Capacitor | 47 nF, 50 V | |
| S1 | 1 | 6.0 x 3.8 mm SMD J−Bend WS−TASV | 100 mQ, 250 V (AC) | 434 123 025 816 |
| C3, C4 | 2 | Capacitor | 100 nF, 16 V |
| C8 | 1 | Capacitor | 100 nF, 50 V | |
| C1 | 1 | Capacitor | 100 nF, 16 V | |
| C7 | 1 | Capacitor | 100 nF, 50 V | |
| R18 | 1 | Mohanyetsi | 130 Q | |
| C6 | 1 | Capacitor | 220 nF, 50 V | |
| R1, R4, R5, R34 | 4 | Mohanyetsi | 560 Q | |
| LED6 | 1 | Mount Mount Chip LED, e khubelu | 0603, khubelu | KPT−1608EC |
| R33, R38 | 2 | Mohanyetsi | 680 Q | |
| R14, R35, R36 | 3 | Mohanyetsi | 750 Q | |
| LED1, LED5 | 2 | LED, Khubelu, 2.4 limilimithara, 636 nm, 1.8 V, 2 mA,
18 mcd |
Led, Red, 1.8 V, 2 mA | Setšoantšo sa VLMS30J1L2−GS08 |
| J5 | 1 | Sehokelo sa banna sa WAGO 243−211 | Bophahamo: 5.75 limilimithara / Bophara: 1 mm / 100 V / 6 A | 243−211Banna |
| D3 | 1 | Surface Mount Schottky Power Rectifier | Uf = 430 mV,
Haeba = 500 mA, Ur = 30 V |
Setšoantšo sa MBR0530T1G |
Mofuta o fokolang oa BoM
Lethathamo la 12: BILL OF MATERIALS bonyane BOM VERSION
| Moqapi | Qty | Tlhaloso | Boleng | Nomoro ea Karolo |
| J1 | 1 | WR−PHD 2.54 mm THT Pin Header, 03p | 61300311121 | |
| J4 | 1 | Sehokelo sa Boto ho ea ho Boto, 2.54 mm,
Mabitso a 8, Mokelikeli, ka Mokoti, Mela e 1 |
SSQ−110−03−G−S | |
| J6 | 1 | Sehokelo sa Boto-to-Boto, 2.54 mm, Mabitso a 10, Mohaho, ka Mokoti, Mela e 1 | SSQ−110−03−G−S | |
| J7 | 1 | Sehokelo sa Boto ho ea ho Boto, 2.54 mm,
Mabitso a 6, Mokelikeli, ka Mokoti, Mela e 1 |
SSQ−106−03−G−S | |
| J9 | 1 | Sehokelo sa Boto ho ea ho Boto, 2.54 mm,
Mabitso a 8, Mokelikeli, ka Mokoti, Mela e 1 |
SSQ−108−03−G−S | |
| J11 | 1 | WR−PHD 2.54 mm THT Pin Header, 2p | ||
| L3 | 1 | SMT Power Inductor WE−LQFS, siz−e 4828,
220 µH, 0.4 A |
||
| Q1 | 1 | Mokhoa oa Ntlafatso ea Boemo ba Monahano oa N-Channel
Field Effect Transistor, 30 V, 1.7 A, 55°C, 3-Pin SOT−3, RoHS, Tape le Reel |
||
| U2 | 1 | E le 'ngoe 2−Keno LE Heke | MC74HC1G08DTT1G | |
| R6, R9, R11, R12, R16 | 5 | Mohanyetsi | 0 Q | |
| D1 | 1 | Schottky Rectifier, Single 60 V, 1 A, DO−214AC, 2 Pins, 720 mV | 1 A / 720 mV / 60 V | SS16T3G |
| R21 | 1 | Mohanyetsi | 1 Q | |
| LED3 | 1 | LED, Yellow, SMD, 2 mA, 2.2 V, 594 nm | 2 mA, 2.2 V, 594 nm | VLMA3100−GS08 |
| R19 | 1 | 2 (1 x 2) Position Shunt Connector
Khauta e sa kenngoeng ka 0.400in (10.16 mm). |
2 phini | D3082−05 |
| LED4 | 1 | LED, Orange, SMD, 2.4 mm, 2 mA, 1.8 V,
609 nm |
2.4 mm, 2 mA, 1.8 V,
609 nm |
Setšoantšo sa VLMO30L1M2−GS08 |
| LED2 | 1 | LED, Botala, SMD, 2.4 mm, 2 mA, 1.9 V,
575 nm |
2.4 mm, 2 mA, 1.9 V,
575 nm |
VLMMC3100−GS08 |
| C12 | 1 | Capacitor | 10 µF | |
| R2, R3, R7, R8, R26, R27, R28, R29, R37 | 9 | Mohanyetsi | 10 Q | |
| 4 | Fetoha | 12 V, 50 mA | MCDTS6−3N | |
| R10 | 1 | Mohanyetsi | 27 Q | |
| U1 | 1 | Transceiver bakeng sa KNX Twisted Pair Networks | 40 phini | NCN5110 |
| D2 | 1 | SMAJ40CA − TVS Diode, TRANZORB
SMAJ Series, Bidirectional, 40 V, 64.5 V, DO−214AC, 2 Pins |
40 V, 400 W | SMAJ40CA |
| C9 | 1 | Capacitor | 47µF, 35 V | |
| C5 | 1 | Capacitor | 47 nF, 50 V | |
| S1 | 1 | 6.0 x 3.8 mm SMD J−Bend WS−TASV | 100 mQ, 250 V (AC) | 434 123 025 816 |
| C3, C4 | 2 | Capacitor | 100 nF, 16 V | |
| C8 | 1 | Capacitor | 100 nF, 50 V | |
| C1 | 1 | Capacitor | 100 nF, 16 V | |
| C7 | 1 | Capacitor | 100 nF, 50 V | |
| C6 | 1 | Capacitor | 220 nF, 50 V | |
| R1, R4, R5, R34 | 4 | Mohanyetsi | 560 Q |
| LED6 | 1 | Mount Mount Chip LED, e khubelu | 0603, khubelu | KPT−1608EC |
| R33, R38 | 2 | Mohanyetsi | 680 Q | |
| R14, R35, R36 | 3 | Mohanyetsi | 750 Q | |
| LED1, LED5 | 2 | LED, Khubelu, 2.4 limilimithara, 636 nm, 1.8 V, 2 mA,
18 mcd |
Led, Red, 1.8 V, 2 mA | Setšoantšo sa VLMS30J1L2−GS08 |
| J5 | 1 | Sehokelo sa banna sa WAGO 243−211 | Bophahamo: 5.75 limilimithara / Bophara: 1 mm / 100 V / 6 A | 243−211Banna |
Arduino ke lets'oao la khoebo la Arduino AG.
Mabitso a mang kaofela le mabitso a lihlahisoa a hlahang tokomaneng ena ke matšoao a khoebo a ngolisitsoeng kapa matšoao a beng ba ona ka ho fapana. qala, le mabitso a mang, matshwao, le mabitso a ngodisitsweng le/kapa matshwao a kgwebo a tlwaelehileng a Semiconductor Components Industries, LLC dba “onsemi” kapa mafapha a yona le/kapa ditsiane tsa United States le/kapa dinaha tse ding. onsemi o na le litokelo tsa litokelo tse ngata tsa litokelo tsa molao, matšoao a khoebo, litokelo tsa molao, liphiri tsa khoebo, le thepa e 'ngoe ea bohlale. Lethathamo la ts'ireletso ea sehlahiswa/patent ea onsemi e ka fihlelleha ho www.onsemi.com/site/pdf/Patent−Marking.pdf. onsemi ke Mohiri oa Monyetla o Tekano/Affirmative Action Employer. Lingoliloeng tsena li tlas'a melao eohle e sebetsang ea litokelo 'me ha li rekisoe ka mokhoa leha e le ofe.
Boto ea tlhahlobo/kit (boto ea lipatlisiso le nts'etsopele) (ka mor'a mona "boto") ha se sehlahisoa se felileng ebile ha se fumanehe bakeng sa bareki. Boto e reretsoe feela merero ea lipatlisiso, nts'etsopele, lipontšo le tlhahlobo 'me e tla sebelisoa feela libakeng tsa laboratori / nts'etsopele ke batho ba nang le koetliso ea boenjiniere / botekgeniki le ba tloaelaneng le likotsi tse amanang le ho sebetsana le likarolo tsa motlakase / tsa mochini, litsamaiso le litsamaiso tse nyane. Motho enoa o nka boikarabelo bo feletseng / boikarabelo ba ho sebetsana ka tsela e nepahetseng le e sireletsehileng. Tšebeliso efe kapa efe e 'ngoe, thekiso kapa kabo bocha bakeng sa morero ofe kapa ofe o thibetsoe ka thata.
BOTO E FUMANA KE ONSEMI HO WENA "JOALOKAHA E LE" HONA KA NTLE LE LITŠOANTŠISO KAPA LITIISETSO TSEFELENG. KA NTLE LE HO LEKELA TSE FELELE, ONSEMI (Mmoho le BA-LICENSI/BABAPELI BA EONA) KA ONA E HLAKOLA LITEMELETSO LE TSOHLE LE LITIISETSO MAHALA LE BOTO, LIPHETOHO life kapa life, KAPA TUMELLANO ENA, E KA TSOHLE, HO HLAHALA, HO HLAHISITSOE, HO HLAHISITSOE, HO HLOKAHALA KA TSOHLE. TS'ELISO LE DITIISETSO TSA THEKISO, HO LOKELANG HO FIHLELA MORERO O KHETHEHILENG, SEHLOOHO, HO SE TLOHLO, LE TSE TSOANG HO TSOA MOKHOA OA HO SEBELISANA, TŠEBELETSO EA LIKHOEBO, LITABA TSA KHOEBO KAPA TETELO EA Kgwebo. onsemi e na le tokelo ea ho etsa liphetoho ntle le tsebiso e 'ngoe ho boto efe kapa efe.
U na le boikarabelo ba ho etsa qeto ea hore na boto e tla ba e loketseng bakeng sa tšebeliso eo u e rerileng kapa kopo kapa e tla finyella liphello tseo u li rerileng. Pele o sebelisa kapa o aba litsamaiso life kapa life tse hlahlobiloeng, tse entsoeng kapa tse lekiloeng ka boto, u lumela ho leka le ho netefatsa moralo oa hau ho netefatsa ts'ebetso ea kopo ea hau. Tlhahisoleseding efe kapa efe ya tekheniki, ditshebediso kapa boqapi kapa boeletsi, tlhabollo ya boleng, datha tsa botshepehi kapa ditshebeletso tse ding tse fanwang ke onsemi e ke ke ya ba boemedi kapa waranti efe kapa efe ka qala, mme ha ho tlamo kapa mekoloto e tla hlaha ho tloha ho qala ho fana ka tlhahisoleseling kapa lits'ebeletso tse joalo.
Lihlahisoa tsa onsemi ho kenyeletsoa liboto ha lia etsoa, tsa rereloa, kapa ha lia lumelloa ho sebelisoa lits'ebetsong tsa ts'ehetso ea bophelo, kapa lisebelisoa life kapa life tsa bongaka tsa FDA Class 3 kapa lisebelisoa tsa bongaka tse nang le sehlopha se ts'oanang kapa se lekanang sebakeng sa kantle ho naha, kapa lisebelisoa life kapa life tse reretsoeng ho kengoa ho motho. mmele. O lumela ho qosa, ho sireletsa le ho boloka tsohlemi e se nang kotsi, batsamaisi ba eona, liofisiri, basebetsi, baemeli, baemeli, lithuso, litšebelisano, barekisi, le ho abela, khahlanong le mekoloto efe kapa efe, tahlehelo, litšenyehelo, lits'enyehelo, likahlolo le litšenyehelo tse hlahang. ya tseko efe kapa efe, tlhokahalo, dipatlisiso, qoso, ketso ya taolo kapa sesosa sa ketso e hlahang kapa e amanang le tshebediso efe kapa efe e sa dumellwang, leha tseko e jwalo e qosa hore onyomi o ne a sa tsotelle mabapi le moralo kapa tlhahiso ya dihlahiswa dife kapa dife le/kapa boto. Boto/kit ena ea tlhahlobo ha e oele ka har'a litaelo tsa European Union mabapi le ts'ebelisano ea motlakase, lintho tse thibetsoeng (RoHS), recycling (WEEE), FCC, CE kapa UL, 'me e kanna ea se fihlelle litlhoko tsa tekheniki tsa litaelo tsena kapa tse ling tse amanang. .
TLHOKOMELISO ea FCC: Letlapa lena la tlhahlobo le reretsoe ho sebelisoa molemong oa nts'etsopele ea boenjineri, lipontšo, kapa tlhahlobo feela 'me ha e nkuoe ke onsemi e le sehlahisoa se felileng se loketseng tšebeliso ea bareki ka kakaretso. E ka hlahisa, ea sebelisa, kapa ea khantša matla a maqhubu a seea-le-moea 'me ha e so etsetsoe teko ea ho lumellana le meeli ea lisebelisoa tsa khomphutha ho latela karolo ea 15 ea melao ea FCC, e etselitsoeng ho fana ka tšireletso e utloahalang khahlano le tšitiso ea maqhubu a radio. Ts'ebetso ea sesebelisoa sena e ka baka tšitiso ea likhokahano tsa seea-le-moea, moo mosebelisi a tla ikarabella, ka litšenyehelo tsa eona, ho nka mehato efe kapa efe e ka hlokoang ho lokisa tšitiso ena. onsemi ha e fane ka laesense efe kapa efe tlasa litokelo tsa eona tsa patent kapa litokelo tsa ba bang.
MEKHAO EA MOLAMO: onsemi e ke ke ea ikarabella bakeng sa tšenyo efe kapa efe e khethehileng, e bakoang, e sa lebelloang, e sa tobang kapa ea kotlo, ho kenyeletsoa, empa e sa felle feela ho litšenyehelo tsa prequalification, tieho, tahlehelo ea phaello kapa kamohelo, e hlahang kapa e amanang le boto, le haeba e eletsoa ka monyetla oa tšenyo e joalo. Leha ho le joalo, ha ho na ketsahalo e tla tlameha ho feta tefiso e lefshoang bakeng sa boto, haeba e le teng. Boto e fanoa ho uena ho latela laesense le lipehelo tse ling ho latela lipehelo le lipehelo tse tloaelehileng tsa thekiso. Ho fumana lintlha tse ling le litokomane, ka kopo etela www.onsemi.com.
TLHAHISOLESELING E 'NGOE
DIKGATISO TSA TSELA:
- Laeborari ea Tekheniki: www.onsemi.com/design/resources/technical-documentation
- tsohle Websebaka: www.onsemi.com
- TŠEHETSO EA INTERNET www.onsemi.com/support
- Ho fumana lintlha tse ling, ka kopo ikopanye le Moemeli oa Thekiso ea sebakeng sa heno ho: www.onsemi.com/support/sales
Litokomane / Lisebelisoa
 |
ON Semiconductor NCN5100 Arduino Shield Evaluation Board [pdf] Bukana ea Mosebelisi NCN5100 Arduino Shield Evaluation Board, NCN5100, Arduino Shield Evaluation Board, Boto ea Tlhahlobo ea Shield, Boto ea Tlhahlobo, Boto |
