Light Stream Running le ho Itloaetsa Maemo a Leseli Tataiso ea Mosebelisi
Player V2 Δημιουργία τρεξίματος και προσαρμογής φωτεινών σεναρίων
Εξοπλισμός
| • Light Stream Player V2 | • Μετατροπέας Light Stream | • Λογισμικό Light Stream |
|
 |
 |
Setšoantšo sa wiring
Accessing Light Stream Player
Accessing Light Stream Player is done using a web-browser atereseng e fanoeng ea IP ho tsoa komporong, mohala kapa tablet e nang le phihlello ea Marang-rang.
To connect, the network card and Light Stream Player must be on the same subnet.
Haeba ho hlokahala, fetola aterese ea IP ea karete ea marang-rang.
Exampmohlala: Windows 10
- Eya ho Lihokelo tsa Marang-rang (Paneli ea Taolo / Marang-rang le Lihokelo tsa Marang-rang / Marang-rang)
Select an active network connection, right-click (right mouse button) and select Properties.
- Mofuta o latelang oa IP 4 (TCP/IPv4) -> Thepa.
- Since the Light Stream Player has a default
IP Aterese: 192.168.0.205
Bakeng sa mohlalaample, leIP Address: 192.168.0.112
This address must be unique and must not be repeated with other devices on the network.
Subnet Mask: 255.255.255.255.0
Then, go to your web sebatli ebe o kenya liparamente tse latelang.
Litlhaloso tsa kamehla tsa ho kena:
You are now in the Light Stream Player interface.
Next, it is necessary to change the network parameters of the Light Stream Player to complete the configuration.
Change Light Stream Player network parameters
Network settings using the Player V2 menu display and control buttons.
Karolong ea Network, u ka khona view paramente ea hona joale:
Aterese ea IP, mask, heke le aterese ea MAC ho boema-kepe ba Ethernet 1 le 2.
Ho fetola li-setting tsa marang-rang ho tsoa nthong efe kapa efe e skrineng sa Ethernet 1 kapa 2, tobetsa
.
Static IP Configuration.
On the IP Address screen, place the cursor on the desired value and change the value using le .
To move to the next NETMASK screen, place the cursor on the rightmost digit and press the button again .
On the NETMASK screen, you can change the network mask using the le likonopo .
Then, press the button to move to the Set Gateway screen.
Haeba o hloka ho beha heke ea IP, khetha E 'me u hlalose aterese ea eona ea IP.
Ebe u khutlela skrineng sa Ethernet 1 kapa 2.
Ho tla nka metsotsoana e meng ea 2-3 ho ntlafatsa litlhophiso tsa marang-rang.
Khutlisa litlhophiso tsa marang-rang ka DHCP.
Ho skrine ea Kabelo ea IP, khetha dhcp ebe o tobetsa .
Ho tla nka metsotsoana e meng ea 2-3 ho ntlafatsa litlhophiso tsa marang-rang.
Changing the network parameters of the Light Stream Converter
The network card and the Light Stream Converter must be on the same subnet.
Haeba ho hlokahala, fetola aterese ea IP ea karete ea marang-rang.
The default IP address and other data are indicated on the device information label.
Go to the Light Stream software and then:
Programs->Search->Ethernet Device->Search
Totobatsa converter e fumanoeng-> Litlhophiso.
Fetola aterese ea IP ho aterese ea IP eo u e batlang.
Changing the network settings of the Light Stream Converter is complete.
Ho beha letsatsi le nako
To configure network settings Go to Settings->Date & Time
Tlhokomeliso: These settings may affect the operation of the Programmer mode.
Ho eketsa lisebelisoa tsa Art-Net le bokahohle
Further work will require adding devices and universes.
Go to Settings-> Universe and devices.
Kenya lisebelisoa le bokahohle ka litsela tse peli:
Mokhoa oa 1: U sebelisa likonopo tsa Add.
Click Add ArtNet Device
In the Add Devices window, fill in:
- Name – name of the device.
- Network mode -unicast (preferred);
- IP address – network address of the device.
- Boema-kepe - ka ho sa feleng 6454;
- Tlhaloso – tlhaloso, mohlala, nomoro ea ketsahalo.
To add universes, click Add Universe and in the window that opens, fill in:
- Number – universe number (numbering is end-to-end according to the ArtNet v.4 protocol), in addition, the universe number according to the ArtNet v.3 protocol (Net.Subnet.Universe) is displayed.
- Sesebelisoa sa ArtNet - khetha sesebelisoa se kentsoeng pele.
Mokhoa oa 2: Automatically import from Light Stream software.
Go to Light Stream, then: Photos-> select Light Stream Player-> enter Username and Password-> click the Submit button.
After that, refresh the Light Stream Player web-browser page.
Lisebelisoa tsa ArtNet le bokahohle li ekelitsoe.
Ho theha le ho kenya li-animation
You will need ready-made animations for download, and you can learn how to create them on our YouTube channel ( https://www.youtube.com/@lightstreampro/featured ) and, in particular, in the video (Quick Start in the Light Stream Program) at the link: https://www.youtube.com/watch?v=7yMR__kkpFY&ab_channel=LightStream
Exporting completed animations from Light Stream
Ebe u ea ho web-interface of Light Stream Player and download ready-made animations
Taba ea cues-> Kenya konopo ea Cue
Synchronize the frame rate of animations in the settings of Light Stream Software and Light Stream Player.
Go to the Settings->Player tab, and in the FPS line.set the value equal to the Frame rate parameter (the window pops up when you press the left button during animation in Light Stream software).
The cartoons have been uploaded.
Etsa lenane la lipina
Go to the “Playlists” tab and click “Add Playlist.”
Click Add hint.
Select the animations you want and click Add.
Playlist creation completed
Creating events and scenarios
To create an event, go to the Schedule tab->Event List->Add Event
Read more about the Repeat function.
There are several ways to select Frequency:
Hourly mokhoa.
Create a backup copy
To save backup settings or to transfer settings from one player to another, use the Backup function.
In the Light Stream Player web-interface, go to the Settings->Maintenance tab.
Kea u babatsa!
Litlhophiso tsa mantlha li entsoe!
www.lightstream.pro
Tataiso ea ho Qala ka Potlako
E ntlafalitsoe: Pulungoana 2024
Litokomane / Lisebelisoa
 |
Light Stream Running And Customizing Light Scenarios [pdf] Bukana ea Mosebelisi EN |