FALLTECH 5410A5 Cold Shrink Tool Attachment
Litlhaloso
- Lebitso la Sehlahiswa: Cold Shrink Tool Attachment
- Moetsi: Ha ea hlalosoa
- Nomoro ea Mohlala: MTOL08 Rev B
- Nomoro ea Karolo: 013125
Litaelo tsa Tšebeliso ea Sehlahisoa
BOHLOKOA TŠIRELETSO
Please read and understand the manufacturer’s instructions for each component or part of the complete system. Manufacturer instructions must be followed for proper use, care, and maintenance of this product. These instructions must be retained and kept available for the worker’s reference at all times. Alterations or misuse of this product, or failure to follow instructions, may result in serious injury or death.
LITEMOSO LE MOFELO
- Le ka mohla u se ke ua sebelisa likarolo tsa FallTech For Tools® bakeng sa ho ts'oaroa ha motho ka ho oa, ho ithiba kapa ho beha maemo mosebetsing.
- Inspect the FallTech For Tools® components before each use according to the requirements in Section 6 below.
- Never modify or alter the FallTech For Tools® components; this includes extending the length or tying knots in the tool tethers.
- Never tether any tool or equipment to yourself that weighs more than 5 lbs.
- Le ka mohla u se ke ua sebelisa sehlahisoa sena ho tlama thipa, lehare le bohale, kapa sesebelisoa se seng se bohale.
- Hang-hang hlahloba likarolo tsa FallTech For Tools® bakeng sa tšenyo haeba sesebelisoa se theohile.
- Se ke oa sebelisa sehlahisoa sena ho lisebelisoa kapa lisebelisoa tse fetang matla a rekiloeng a karolo e kentsoeng tlase ho sistimi ea FallTech For Tools®.
- Se ke oa sebelisa sehlahisoa sena haeba se tla kena-kenana le lisebelisoa life kapa life tsa ts'ireletso ea motho ka mong kapa ts'ebetso ea lisebelisoa kapa lisebelisoa tse hokahaneng.
- Qoba ho sebelisa mochini o tsamaisang, mocheso, motlakase, le/kapa likotsi tsa lik'hemik'hale, kaha ho kopana ho ka baka kotsi e mpe kapa lefu.
- Etsa bonnete ba hore ho na le sebaka se lekaneng sa ho tlosa lisebelisoa. Tsela ea ho oa/ts'epo ea sesebelisoa ha ea lokela ho beha uena kapa basebetsi ba bang kotsing.
- Mekhoa eohle e bontšitsoeng litaelong tsena ke ea lihlahisoa tsa FallTech For Tools® feela.
- Tlaleha liketsahalo tsohle tsa lisebelisoa tse lahliloeng ho mookameli oa hau kapa mohokahanyi oa polokeho.
- Se ke oa sebelisa sehlahisoa sena mochesong o ka tlase ho -31 degrees F (-35 degrees C) kapa ka holimo ho 113 degrees F (45 degrees C)
Tlhaloso
The FallTech For Tools® Cold Shrink Tool Attachments are used with FallTech Choke-on Cinch Loop tool attachments to create an attachment point for most hand tools, power tools, and other equipment to attach to FallTech® Tool Tethers, Wrist Attachments, and Tool Anchors.
Kopo
The FallTech For Tools® Cold Shrink Tool Attachments are designed to be used as a component in a dropped object prevention program. The tool
tethering system is an assembly of components and subsystems to arrest a tool from an accidental drop. The system typically consists of a tool attachment, a tool tether, and a tool anchor. See product labels for maximum load capacity and maximum allowable tether length.
Litlhoko tsa Tsamaiso
The FallTech For Tools® Cold Shrink Tool Attachments are designed for use with a single tool. DO NOT exceed the capacity of the lowest rated component in the system.
Ho lumellana ha Likarolo:
Thepa e etselitsoe ho sebelisoa le likaroloana tse lumelletsoeng le litsamaiso tse nyane feela. Phapanyetsano kapa tse nchafalitsoeng tse entsoeng ka likaroloana tse sa lumelloeng kapa litsamaiso tse nyane li ka beha ts'ebelisano ea lisebelisoa kotsing mme li ka ama polokeho le ts'epahalo ea sistimi e felletseng.
Ho theha likhokahano:
Only use locking connectors with this equipment. Only use connectors that are suitable to each application. Ensure all connections are compatible in size, shape, and strength. Do not use equipment that is not compatible. Visually ensure all connectors are fully closed and locked.
Ho kenya
Tlhahlobo ea Pele ho Tšebeliso:
Inspect the tool attachments thoroughly before attaching them to the tool for missing or damaged parts. Inspect the webbing, looped ends, and stitches for cuts, fraying, and signs of damage to the materials from excessive wear or abrasion. Inspect the split rings, D-rings, carabiners, and speed clips for excessive wear, cracks, or deformities. If any of these conditions exist, remove from service.
Mokhoa oa ho Kenya:
Ensure the cold shrink, tool and tool attachment are clean and free of oil, grease, or debris, which could prevent adequate attachment onto the tool. The Cold Shink and Tool Attachment should be placed away from the functional parts of the tool, and the connection point should face away from the centre of gravity. See the figures below for the installation steps by type of attachment.
Choke-On Cinch Loop Installation Procedure:
Position the Choke-on Cinch Loop Tool Attachment high up on the shaft of the tool, pull the anchor end through the elastic loop and pull the tool attachment to choke down onto the tool, see Figure 1. Snug the barrel lock onto the elastic loop to maintain a tight fit of the elastic cord.
Cold Shrink Sizing Selection:
Select the appropriate size cold shrink to fit over the shaft of the tool and the tool attachment. The cold shrink should be the smallest size that will fit over the tool and tool attachment. If the size of the cold shrink is too large, the cold shrink will not contact enough to maintain a tight fit on the tool attachment and allow it to slip off during an accidental drop.
Cold Shrink Installation:
Slide the cold shrink over the shaft of the tool and the tool attachment with the pull direction arrow on the cold shrink pointing away from the cinched nylon cord, see Figure 2. Position the cold shrink below the choked-onnylon cord and barrel lock, see Figure 3. Pull the free end of the cold shrink inner core. This will allow the cold shrink to contract over the tool shaft and tool attachment. Attach a tool lanyard and anchor to complete the system, see Figure 4.
This manual is intended to meet the Manufacturer’s Instructions as required by the American National Standards Institute (ANSI), International Safety Equipment.
Mokhatlo (ISEA) mme e lokela ho sebelisoa e le karolo ea lenaneo la koetliso ea basebetsi joalokaha ho hlokoa ke Occupational Safety and Health Administration (OSHA).
Tlhokomelo, Tšebeletso le Polokelo
Tlhokomelo:
Ha ho hlokahale tokiso e reriloeng, ntle le ho nkela lintho tse seng li hlotsoe tlhahlobo.
Tšebeletso:
Ha ho na litlhoko tse khethehileng tsa tšebeletso bakeng sa karolo ena ea tsamaiso.
Polokelo:
Boloka sebakeng se hloekileng, se omeletseng, se se nang lik'hemik'hale ntle le letsatsi. Qoba ho pepesehela maemo a mocheso nako e telele.
Tlhahlobo
Inspect the FallTech For Tools® Cold Shrink Tool Attachments per the inspection procedure in Section 4.1. If any abnormalities are found, remove from service.
| FallTech For Tools® Cold Shrink Tool Attachment Specifications | ||||
| Mohlala # | Tlhaloso | Dimensions (ID x Length) | Bokhoni le Maemo | Tool Shackle Attachment Image |
|
Ho fihlela ho 5 lbs. (6.8 lik'hilograma) |
|
|||
| 5410A5 | Tool Attachment, 5 lbs, Cold Shrink, Small, 5/pk | 1.75" (44.5mm) x 1.6" (42mm) | ||
| ANSI/ISEA
121-2018 |
||||
|
Ho fihlela ho 10 lbs. (6.8 lik'hilograma) |
||||
| 5411A5 | Tool Attachment, 10 lbs, Cold Shrink, Medium, 5/pk | 2.25" (57mm) x 3.0" (76.2mm) | ||
| ANSI/ISEA
121-2018 |
||||
|
Ho fihlela ho 15 lbs. (6.8 lik'hilograma) |
||||
| 5412A5 | Tool Attachment, 15 lbs, Cold Shrink, Large, 5/pk | 3.0" (76.2mm) x 4.5" (114.3mm) | ||
| ANSI/ISEA
121-2018 |
||||
FAQS
Q: What should I do if I find damaged parts during the pre-use inspection?
A: If any damaged parts are found, do not use the product and remove it from service immediately for repair or replacement.
Q: Can I use non-approved components with this tool attachment?
A: No, only use approved components and subsystems as stated in the user manual to ensure safety and reliability.
Litokomane / Lisebelisoa
 |
FALLTECH 5410A5 Cold Shrink Tool Attachment [pdf] Buka ea Taelo Rev_B_013125, 5410A5 Cold Shrink Tool Attachment, 5410A5, Cold Shrink Tool Attachment, Shrink Tool Attachment, Tool Attachment, Attachment |