FALLTECH 5410A5 Cold Shrink Tool Attachment
Espesifikasyon
- Non pwodwi: Atachman Zouti Retresi Fwad
- Manifakti: Pa espesifye
- Nimewo Modèl: MTOL08 Rev B
- Nimewo Pati: 013125
Enstriksyon Itilizasyon Pwodwi
ENFÒMASYON SEKIRITE ENPÒTAN
Please read and understand the manufacturer’s instructions for each component or part of the complete system. Manufacturer instructions must be followed for proper use, care, and maintenance of this product. These instructions must be retained and kept available for the worker’s reference at all times. Alterations or misuse of this product, or failure to follow instructions, may result in serious injury or death.
AVÈTISMAN AK LIMIT
- Pa janm sèvi ak konpozan FallTech For Tools® yo pou arete yon moun ki tonbe, pou kontwole l, oswa pou pozisyone nan travay.
- Inspect the FallTech For Tools® components before each use according to the requirements in Section 6 below.
- Never modify or alter the FallTech For Tools® components; this includes extending the length or tying knots in the tool tethers.
- Never tether any tool or equipment to yourself that weighs more than 5 lbs.
- Pa janm sèvi ak pwodui sa a pou mare yon kouto, yon lam byen file, oswa yon lòt zouti byen file.
- Enspekte konpozan FallTech For Tools® yo imedyatman si zouti a te tonbe.
- Pa sèvi ak pwodui sa a sou zouti oswa ekipman ki depase kapasite nominal konpozan ki gen pi ba kapasite nan sistèm FallTech For Tools® la.
- Pa sèvi ak pwodui sa a si li pral entèfere ak nenpòt ekipman pwoteksyon pèsonèl tonbe oswa operasyon an nan zouti ki konekte oswa ekipman yo.
- Evite itilize li toupre machin k ap deplase, danje tèmik, elektrik, ak/oswa chimik, paske kontak ka lakòz blesi grav oswa lanmò.
- Asire w ke gen ase espas pou zouti a tonbe. Chemen zouti a ap tonbe/balanse pa dwe mete ou menm oswa okenn lòt travayè an danje.
- Tout pwosedi ki nan enstriksyon sa yo se pou pwodwi FallTech For Tools® sèlman.
- Rapòte tout ensidan zouti ki tonbe bay sipèvizè w oswa kowòdonatè sekirite w la.
- Pa sèvi ak pwodui sa a nan tanperati ki anba a -31 degre F (-35 degre C) oswa pi wo a 113 degre F (45 degre C)
Deskripsyon
The FallTech For Tools® Cold Shrink Tool Attachments are used with FallTech Choke-on Cinch Loop tool attachments to create an attachment point for most hand tools, power tools, and other equipment to attach to FallTech® Tool Tethers, Wrist Attachments, and Tool Anchors.
Aplikasyon
The FallTech For Tools® Cold Shrink Tool Attachments are designed to be used as a component in a dropped object prevention program. The tool
tethering system is an assembly of components and subsystems to arrest a tool from an accidental drop. The system typically consists of a tool attachment, a tool tether, and a tool anchor. See product labels for maximum load capacity and maximum allowable tether length.
Kondisyon sistèm
The FallTech For Tools® Cold Shrink Tool Attachments are designed for use with a single tool. DO NOT exceed the capacity of the lowest rated component in the system.
Konpatibilite nan eleman:
Ekipman fèt pou itilize ak konpozan ak subsistèm apwouve sèlman. Ranplasman oswa ranplasman ki fèt ak konpozan oswa subsistèm ki pa apwouve yo ka mete an danje konpatibilite ekipman yo epi yo ka afekte sekirite ak fyab sistèm konplè a.
Fè Koneksyon:
Sèlman sèvi ak konektè bloke ak ekipman sa a. Sèlman sèvi ak konektè ki apwopriye pou chak aplikasyon. Asire w ke tout koneksyon yo konpatib nan gwosè, fòm ak fòs. Pa sèvi ak ekipman ki pa konpatib. Asire w vizyèlman ke tout konektè yo byen fèmen epi bloke.
Enstalasyon
Enspeksyon anvan itilizasyon:
Inspect the tool attachments thoroughly before attaching them to the tool for missing or damaged parts. Inspect the webbing, looped ends, and stitches for cuts, fraying, and signs of damage to the materials from excessive wear or abrasion. Inspect the split rings, D-rings, carabiners, and speed clips for excessive wear, cracks, or deformities. If any of these conditions exist, remove from service.
Pwosedi enstalasyon:
Ensure the cold shrink, tool and tool attachment are clean and free of oil, grease, or debris, which could prevent adequate attachment onto the tool. The Cold Shink and Tool Attachment should be placed away from the functional parts of the tool, and the connection point should face away from the centre of gravity. See the figures below for the installation steps by type of attachment.
Choke-On Cinch Loop Installation Procedure:
Position the Choke-on Cinch Loop Tool Attachment high up on the shaft of the tool, pull the anchor end through the elastic loop and pull the tool attachment to choke down onto the tool, see Figure 1. Snug the barrel lock onto the elastic loop to maintain a tight fit of the elastic cord.
Cold Shrink Sizing Selection:
Select the appropriate size cold shrink to fit over the shaft of the tool and the tool attachment. The cold shrink should be the smallest size that will fit over the tool and tool attachment. If the size of the cold shrink is too large, the cold shrink will not contact enough to maintain a tight fit on the tool attachment and allow it to slip off during an accidental drop.
Cold Shrink Installation:
Slide the cold shrink over the shaft of the tool and the tool attachment with the pull direction arrow on the cold shrink pointing away from the cinched nylon cord, see Figure 2. Position the cold shrink below the choked-onnylon cord and barrel lock, see Figure 3. Pull the free end of the cold shrink inner core. This will allow the cold shrink to contract over the tool shaft and tool attachment. Attach a tool lanyard and anchor to complete the system, see Figure 4.
This manual is intended to meet the Manufacturer’s Instructions as required by the American National Standards Institute (ANSI), International Safety Equipment.
Association (ISEA) epi yo ta dwe itilize kòm yon pati nan yon pwogram fòmasyon anplwaye jan Occupational Safety and Health Administration (OSHA) egzije sa.
Antretyen, Sèvis ak Depo
Antretyen:
Pa gen okenn antretyen pwograme obligatwa, lòt pase ranplasman nan atik ki echwe enspeksyon.
Sèvis:
Pa gen okenn kondisyon sèvis espesifik pou eleman sistèm sa a.
Depo:
Sere nan yon anviwonman pwòp, sèk, san pwodui chimik, deyò limyè solèy la dirèk. Evite ekspoze pwolonje nan kondisyon chalè ekstrèm.
Enspeksyon
Inspect the FallTech For Tools® Cold Shrink Tool Attachments per the inspection procedure in Section 4.1. If any abnormalities are found, remove from service.
| FallTech For Tools® Cold Shrink Tool Attachment Specifications | ||||
| Modèl # | Deskripsyon | Dimensions (ID x Length) | Kapasite ak Estanda | Tool Shackle Attachment Image |
|
Jiska 5 liv. (6.8 kg) |
|
|||
| 5410A5 | Tool Attachment, 5 lbs, Cold Shrink, Small, 5/pk | 1.75" (44.5mm) x 1.6" (42mm) | ||
| ANSI/ISEA
121-2018 |
||||
|
Jiska 10 liv. (6.8 kg) |
||||
| 5411A5 | Tool Attachment, 10 lbs, Cold Shrink, Medium, 5/pk | 2.25" (57mm) x 3.0" (76.2mm) | ||
| ANSI/ISEA
121-2018 |
||||
|
Jiska 15 liv. (6.8 kg) |
||||
| 5412A5 | Tool Attachment, 15 lbs, Cold Shrink, Large, 5/pk | 3.0" (76.2mm) x 4.5" (114.3mm) | ||
| ANSI/ISEA
121-2018 |
||||
FAQ
Q: What should I do if I find damaged parts during the pre-use inspection?
A: If any damaged parts are found, do not use the product and remove it from service immediately for repair or replacement.
Q: Can I use non-approved components with this tool attachment?
A: No, only use approved components and subsystems as stated in the user manual to ensure safety and reliability.
Dokiman / Resous
 |
FALLTECH 5410A5 Cold Shrink Tool Attachment [pdfManyèl Enstriksyon Rev_B_013125, 5410A5 Cold Shrink Tool Attachment, 5410A5, Cold Shrink Tool Attachment, Shrink Tool Attachment, Tool Attachment, Attachment |