EMERSON EC2-352 Pontšo ea Case le Coldroom Controller
Litlhaloso
- Phepelo ea matla: 24VDC
- Tšebeliso ea matla: 4…20mA
- Puisano: mabitso a SPDT, AgCdO Inductive (AC15) 250V/2A Resistive (AC1) 250V/8A; 12Kakaretso ea ho khutla hona joale
- Boholo ba sehokelo sa plug-in: 24V AC, 0.1 … 1A
- Sebaka sa polokelo ea mocheso: 0…80% rh noncodensing
- Mongobo: IP65 (ts'ireletso e ka pele e nang le gasket)
- Sehlopha sa tšireletso: IP65
- Kenyelletso ea transmitter ea khatello: 24VDC, 4…20mA
- Li-relays: (3) Triac output bakeng sa EX2 Electrical Control Valve Coil (ASC 24V feela)
Litaelo tsa Tšebeliso ea Sehlahisoa
Phetoho ea Parameter
Ho fetola paramente, latela mokhoa o latelang:
- Finyella letlapa la dikonopo.
- Fumana parameter e lakatsehang Lethathamong la Parameters.
- Fetola boleng ba paramente ka har'a sebaka se boletsoeng.
Defrost activation
Defrost cycle e ka kengoa sebakeng sa heno ho tsoa ho keypad. Ho kenya tšebetsong potoloho ea defrost, latela mehato ena:
- Finyella letlapa la dikonopo.
- Khetha khetho ea ho kenya tšebetsong defrost.
Mesebetsi e Ikgethileng
Mesebetsi e khethehileng e ka etsoa ke:
- Ho kena letlapeng la dikonopo.
- Ho khetha mosebetsi o khethehileng o lakatsehang.
Pontšo ea Lintlha
Ho hlahisa data skrineng, latela mehato ena:
- Tobetsa konopo ea SEL ho tsamaisa data eohle e ka hlahang.
- Pontšo e tla bontša sekhetho sa linomoro tsa data ebe data e khethiloeng.
- Kamora metsotso e 'meli, ponts'o e tla khutlela ho data e khethiloeng.
Lipontšo tsa Boemo bo utloahalang
- Relay ea Compressor: E bontša boemo bo utloahalang ba relay ea compressor.
- IR LED: E bontša boemo ba Infrared LED.
- Ts'ebetso ea Ethernet LED: E bonts'a ts'ebetso ea Ethernet (e sebetsa feela ha phini ea litšebeletso e hatelloa).
- Relay ea fan: E bontša boemo bo utloahalang ba phepelo ea fan.
- Defrost heater relay: E bontša boemo bo utloahalang ba "defrost heater relay".
- Boemo ba alamo: E bontša boemo ba alamo.
Hlokomela:
Tokomane ena e na le litaelo tse khutšoane bakeng sa basebelisi ba nang le boiphihlelo. Sebelisa kholomo ea ho qetela Lethathamong la Parameters ho ngola litlhophiso tsa hau ka bomong. Boitsebiso bo eketsehileng bo ka fumanoa ho Buka ea Mosebelisi.
EC2-352 ke sehatsetsi se inehetseng se nang le mocheso o phahameng haholo le mokhanni oa Alco Controls Electric Control Valve EX2. Ho feta moo EC2-352 e laola mocheso oa moea 'me e laola defrost le fan(s).
PT5 pressure transmitter (1) le ECN-Pxx pipe sensor ea mocheso (2) lekanya khatello ea khase e hulang le mocheso oa khase sebakeng sa mouoane ebe se fepa matšoao ho lupu ea taolo ea mocheso o phahameng. The superheat controller output modulates ho buloa ha EX2 pulse wide modulated Electrical Control Valve (6) ka tsela eo ho ntlafatsa phallo ea boima ba sehatsetsing ka mouoane.
ECN-Sxx lisensara tsa mocheso oa moea (3) le (4) li lekanya mocheso oa moea o kenang le ho tsoa oa mouoane le matšoao a fepa ho thermostat ea moea. ECN-Fxx fin sensor (5) e sebelisetsoa ho felisa serame. Molaoli o na le liphetho tse 3 tsa relay ho laola kompressor (7), heater ea defrost (9) le evaporator fan (8). Ka kopo sheba lintlha tsa tekheniki (ka ho le letona) bakeng sa lintlha tse kentsoeng le tse hlahisoang.
Tabeng ea tahlehelo ea matla, ka lebaka la litšobotsi tse ntle tsa ho koala tsa EX2 Motlakase oa Li-Valves tsa Motlakase, valve ea solenoid ea metsi ha e hlokehe ho thibela likhohola tsa compressor.
Litaelo tsa polokeho
- Bala litaelo tsa ho kenya ka botlalo. Ho hloleha ho ikamahanya le maemo ho ka baka ho hloleha ha sesebelisoa, ho senyeha ha sistimi kapa kotsi ea motho.
- Sehlahisoa se reretsoe ho sebelisoa ke batho ba nang le tsebo le bokhoni bo nepahetseng.
- Netefatsa hore lintlha tsa motlakase ho latela data ea tekheniki ha li fetisoe.
- Hakolla kaofela voltages ho tloha tsamaisong pele ho ho kenya.
- Boloka mocheso ka har'a meeli e tloaelehileng.
- Latela melao ea motlakase ea lehae ha u kenya mohala
Lintlha tsa Tekheniki
EC2 Series Controller
| Phepelo ea motlakase | 24VAC ± 10%; 50/60Hz; Sehlopha sa II |
| Tšebeliso ea matla | 20VA max ho kenyelletsa le EX2 |
| Puisano | TCP/IP Ethernet 10MBit/s |
| Boholo ba sehokelo sa plug-in | Removable screw terminals boholo ba terata 0.14 … 1.5 mm2 |
| Ho sebetsa polokelo ea mocheso |
-20 ... +65°C 0 ... +60°C |
| Mongobo | 0…80% rh e sa fokotseng |
| Sehlopha sa tšireletso | IP65 (ts'ireletso e ka pele e nang le gasket) |
| Kenyelletso ea ho fetisa khatello | 24VDC, 4…20mA |
| Li-relay tsa sephetho (3) | Mabitso a SPTD, AgCdO |
| Inductive (AC15) 250V/2A | |
| Ho hanyetsa (AC1) 250V / 8A; 12Kakaretso ea ho khutla hona joale | |
| Triac output bakeng sa EX2 Electrical Control Valve Coil (ASC 24V feela) | 24V AC, 0.1 … 1A |
| Ho tshwaya | EAC |
Ho hlongoa:
EC2-352 e ka kenngoa ka liphanele tse nang le 71 x 29 mm cutout. Sheba setšoantšo se ka tlase bakeng sa litlhoko tsa sebaka ho kenyeletsa le lihokelo tse ka morao. Sutumelletsa selaolo ho phanele cutout.(1)
- Etsa bonnete ba hore li-mounting lugs li na le bokantle ba ntlo ea controller
- Kenya konopo ea allen ka har'a masoba a liphanele tse ka pele 'me u fetohele ho ea ho oache.
- Lithako tse ntseng li phahama li tla reteleha ebe butle-butle li leba phanele (2)
- Fetola konopo ea allen ho fihlela mokotla o ntseng o phahama o sa ame phanele.
- Ebe u tsamaisa mokotla o mong o behang sebakeng se tšoanang (3)
- Tiisa mahlakore ka bobeli ka hloko haholo ho fihlela molaoli a sireletsehile.
- U se ke ua itlama ho feta tekano kaha litšepe tse ntseng li hloa li tla robeha habonolo.
Kemiso ea Motlakase:
Sheba setšoantšo sa lithapo tsa motlakase (ka tlase) bakeng sa likhokahano tsa motlakase. Kopi ea setšoantšo sena e ngotsoe ho molaoli. Sebelisa lithapo tse hokelang/lithapo tse loketseng tšebetso ea 90°C (EN 60730-1)
Lisebelisoa tsa analog tsa EC2 ke tsa li-sensor tse inehetseng feela 'me ha lia lokela ho hokela lisebelisoa tse ling. Ho hokela lisebelisoa life kapa life tsa EC2 ho mains voltage tla senya EC2 ruri.
Bohlokoa: Boloka mohala oa molaoli le oa sensor o arohane hantle le mohala o moholo. Bonyane sebaka se khothalelitsoeng 30mm.
Tlhokomediso: Sebelisa transformer ea sehlopha sa II bakeng sa phepelo ea motlakase ea 24VAC (EN 60742). Se ke oa theola mela ea 24VAC. Re khothaletsa ho sebelisa transformer e le 'ngoe ka molaoli oa EC2 le ho sebelisa li-transformer tse arohaneng bakeng sa balaoli ba mokha oa boraro, ho qoba tšitiso e ka bang teng kapa mathata a motheo phepelong ea motlakase. Ho hokela lisebelisoa life kapa life tsa EC3 ho mains voltage tla senya EC2 ruri.
EC2-352 Pontšo ea Case le Coldroom Controller
Lintlha tsa Maemo a Sensor a khothalelitsoeng:
- ECN-Pxx sensor ea mocheso oa coil-out: Beha ka kotloloho ka mor'a mouoane mothapong o tloaelehileng oa ho hula.
- Mocheso oa mocheso oa moea oa ECN-Sxx: Beha bohareng ba khabinete ka hohle kamoo ho ka khonehang.
- Sensor ea mocheso oa moea oa ECN-Sxx: Beha asymmetric haufi le valve ea ho atolosa ka hohle kamoo ho ka khonehang.
- ECN-Fxx fin sensor ea mocheso: Boemo holim'a mouoane, asymmetric haufi le valve ea ho atolosa.
Litlhahiso tsa ho kenya sensor ea pipe:
Etsa bonnete ba hore o kopana le mocheso o nepahetseng ka ho sebelisa pipe ea tšepe ea clamp kapa marapo a polasetiki a hanyetsanang le mocheso. Se ke oa sebelisa lithae tse tloaelehileng tsa polasetiki (joalo ka ha li sebelisoa bakeng sa likhoele tsa motlakase) kaha li ka 'na tsa hlepha ha nako e ntse e ea, e leng se ka bakang litekanyo tse fosahetseng tsa mocheso le ho se sebetse hantle ha mocheso o phahameng. Ho khothalletsoa ho kenya sensor ea mocheso oa phala ka ARMAFLEX™ kapa e lekanang. Boemo bo khothaletsoang ba li-sensors tsa liphaephe ke pakeng tsa 9 le 3 o'clock joalokaha ho bontšitsoe setšoantšong.
- PT5-07M suction pressure transmitter: Boemo moleng o tloaelehileng oa ho hula haufi le sensor ea mocheso oa coil-out
- (2) Lisensara ka bobeli tsa mocheso oa moea li lokela ho kenngoa holim'a li-spacers ka har'a kotopo ea moea e le hore ho be le phallo ea moea ho potoloha.
Tlhokomeliso: Lithapo tsa sensor li ka atolosoa ha ho hlokahala. Khokahano e tlameha ho sireletsoa khahlanong le metsi le lerole. Sensor ea mocheso ea evaporator e lokela ho behoa holim'a hlooho e tloaelehileng ea mouoane ea mouoane. Tokiso ea ho lekanya e ka etsoa ho sebelisoa parameter u1 (sheba mokhoa o ka tlase).
Seta le Phetoho ea Parameter U sebelisa Keypad
Bakeng sa boiketlo, moamoheli oa infrared bakeng sa yuniti ea boikhethelo ea taolo ea IR e ahiloe, e nolofalletsang phetoho e potlakileng le e bonolo ea liparamente tsa sistimi ha khomphutha e le sieo. Ntle le moo, li-parameter li ka fumaneha ka konopo ea likonopo tse 4. Mekhahlelo ea tlhophiso e sirelelitsoe ke password ea linomoro. Lekunutu la kamehla ke "12". Ho khetha tlhophiso ea paramente:
- Tobetsa konopo ea PRG bakeng sa metsotsoana e fetang 5, ho tla hlaha "0" e phatsimang
- Tobetsa
or 
ho fihlela "12" e hlahisoa (password) - Tobetsa SEL ho netefatsa phasewete
Khoutu ea pele e feto-fetohang e bonts'oa (/1). Ho fetola li-parameter, bona phetoho ea Parameter ka tlase.
Phetoho ea Parameter
Mokhoa:
- Tobetsa or ho bontša khoutu ea parameter e lokelang ho fetoloa;
- Tobetsa SEL ho bonts'a boleng ba paramente e khethiloeng;
- Tobetsa or ho eketsa kapa ho fokotsa boleng;
- Tobetsa SEL ho netefatsa boleng bo bocha ka nakoana le ho bonts'a khoutu ea eona;
- Pheta mokhoa ona ho tloha qalong "tobetsa or ho bontša…”
Ho tsoa le ho boloka litlhophiso tse ncha:
- Tobetsa PRG ho netefatsa boleng bo bocha le ho tsoa ho mokhoa oa ho fetola liparamente.
Ho tsoa ntle le ho fetola paramente efe kapa efe:
- Se ke oa tobetsa konopo efe kapa efe bonyane metsotsoana e 60 (TIME OUT).
- Tobetsa "ESC" ho IR remote control.
Defrost activation:
Sedikadikwe sa defrost se ka kenngwa tshebetsong sebakeng sa heno ho tswa ho keypad:
- Tobetsa ea konopo bakeng sa metsotsoana e fetang 5, ho tla hlaha "0" e benyang
- Tobetsa or ho fihlela "12" e hlahisoa (password)
- Tobetsa SEL ho netefatsa phasewete Nako ea defrost e kentsoe tšebetsong.
Mesebetsi e Ikhethileng:
Mesebetsi e khethehileng e ka etsoa ke:
- Tobetsa le hammoho bakeng sa metsotsoana e fetang 5, ho tla hlaha "0" e benyang.
- Tobetsa or ho fihlela phasewete e hlaha (kamehla = 12). Haeba password e fetotsoe, khetha password e ncha.
- Tobetsa SEL ho netefatsa phasewete, "0" e bonts'itsoe mme mokhoa oa Ts'ebetso e Khethehileng oa buloa.
- Tobetsa or ho kgetha tshebetso. Palo ea mesebetsi e khethehileng e matla ebile e itšetlehile ka molaoli. Sheba lenane le ka tlase.
- Tobetsa SEL ho kenya ts'ebetso ntle le ho siea mokhoa o khethehileng oa ts'ebetso.
- Tobetsa PRG ho kenya ts'ebetso ebe o tlohela mokhoa o ikhethileng oa ts'ebetso.
Boholo ba Mesebetsi e Khethehileng e sebetsa ka mokhoa oa toggle, mohala oa pele o kenya tšebetsong, 'me mohala oa bobeli o tima tšebetso. Pontšo ea ts'ebetso e ka hlahisoa feela ka mor'a ho tsoa ka mokhoa o khethehileng oa ts'ebetso.
- Bontša mosebetsi oa teko
- Hlakola melaetsa ea alamo
- Mokhoa oa ho hloekisa. Mokhoa oa ho hloekisa o sebetsa hantle ka mokhoa oa ho senya ka letsoho ka khetho ea li-fan / off. Mokhoa oa ho hloekisa ha oa lokela ho sebelisoa molemong oa ho arola sesebelisoa molemong oa tlhokomelo.
- Fans feela
- Beha valve ea taolo ea elektroniki hore e bulehe ka 100%.
- E bonts'a aterese ea hajoale ea TCP/IP
- Beha aterese ea TCP/IP ea molaoli ho 192.168.1.101 (boleng ba kamehla). Phetoho ena ke ea nakoana feela. Motlakase o tla seta aterese e fetileng bocha.
- E seta bocha li-parameter tsohle ho ea ho litlhophiso tsa kamehla tsa feme. Mookameli o tla bontša "oF" nakong ea ho tsosolosa 'me valve e tla koala.
Pontšo ea Lintlha:
Lintlha tse lokelang ho bontšoa ka ho sa feleng skrineng li ka khethoa ke mosebelisi (parameter / 1). Haeba ho na le alamo, khoutu ea alamo e hlahisoa ka tsela e fapaneng le data e khethiloeng. Mosebelisi a ka thibela khoutu ea alamo. Hoa khoneha ho bonts'a litekanyetso tsena ka nakoana. Ena ke tšobotsi ea bohlokoa ha u qala ho theha sistimi ntle le thuso ea WebMaqephe. Tobetsa konopo ea SEL ho tsamaea ka har'a data eohle e ka hlahang.
Pontšo e tla bonts'a motsotsoana sekhetho sa linomoro tsa data (bona /1 parameter) ebe data e khethiloeng. Kamora metsotso e 'meli pontšo e tla khutlela ho parameter / 1 data e khethiloeng. Ketso ena e sebetsa feela ha parameter H2 = 3.
Lethathamo la Liparamente
BONTŠA LITŠOANTŠISO
| / | BONTŠA LITŠOANTŠISO | Min | Max | Yuniti | Def. | Tloaelo |
| /1 | Boleng bo lokelang ho bontšoa | 0 | 9 | – | 0 | —- |
| 0 = Thermostat e laola mocheso ka Temp. tlhophiso /C
1 = Thempereichara ea moea °C 2 = Thempereichara ea moea °C 3 = Mocheso oa alamo °C 4 = Mocheso oa ho felisa serame °C 5 = Thempereichara e kenelletseng °C e baloang ho tloha khatellong ea 6 = mocheso oa khoele °C 7 = Mocheso o mongata o baliloeng °K 8 = Ho buloa ha valve ka % 9 = E bonts'a boemo ba defrost |
||||||
| /2 | Khatello ea alamo 0 = tima, 1 = ho | 0 | 1 | – | 0 | —- |
| /5 | Yuniti ya Mocheso 0 = °C, 1 = °F | 0 | 1 | – | 0 | —- |
| /6 | Ntlha ea decimal 0 = e, 1 = che | 0 | 1 | – | 0 | —- |
| /7 | Hlahisa nakong ea defrost | 0 | 2 | – | 0 | —- |
| 0 = dF (= mokhoa oa defrost); 1 = dF + mocheso oa ho felisa serame.
2 = dF + taolo ea mocheso |
||||||
| /C | Tekanyo ea mocheso bakeng sa /1=0 | -20 | 20 | K / °F | 0.0 | —- |
LITŠOANTŠISO TSATSI
| A0 | Mocheso oa alamo o bolelang | 0 | 100 | % | 100 |
| A1 | Ho lieha ha alamo ea mocheso o tlase | 0 | 180 | min | 5 |
| A2 | Ho lieha ha alamo ea mocheso e phahameng | 0 | 180 | min | 5 |
| A3 | Alamo e lieha ka mor'a ho qhibiliha | 0 | 180 | min | 10 |
| AH | Tekanyo e phahameng ea alamo ea mocheso | AL | 70 | °C / K | 40 |
| AL | Tekanyetso ea alamo ea nako e tlase | -55 | AH | °C / K | -50 |
| At | Mofuta oa moeli oa alamo | 0 | 1 | – | 0 |
| 0=lithempereichara tse felletseng °C; 1= mocheso o lekanyelitsoeng oa K ho ea ho setpoint | |||||
r LITŠOANTŠISO TSA THERMOSTAT
| r1 | Min setpoint | -50 | r2 | °C | -50 | —- |
| r2 | Setpoint max | r1 | 60 | °C | 40 | —- |
| r3 | Taolo ea motšehare / bosiu 0 = tima, 1 = ho | 0 | 1 | – | 1 | —- |
| r4 | Mokhoa oa Thermostat | 0 | 4 | – | 1 | —- |
| 0 = e tima, ha ho ts'ebetso ea thermostat, e tsoela pele moea o pholileng ho sensor
tlhokomelo e tima, ha ho na mocheso. dialamo hlahisa 1 = tsidifatso, deadband taolo cut in = set-point + difference cut out = set-point 2 = ho pholile, ho fetola thermostat ho khaola ka = set-point cut out = set-point – phapang /2 3 = futhumatsang, deadband control cut in = set-point – phapang cut out = set-point 4 = ho, taolo ea kantle e sebelisang nvi Valve ka SNMP. Tlhokomelo ea moea o kenang le ho tsoa moeeng e tima. Temp. lialamo li tla hlahisoa |
||||||
| r6 | Setpoint bosiu | r1 | r2 | °C | 4.0 | —- |
| r7 | Bosiu bo fapaneng | 0.1 | 20.0 | K | 2.0 | —- |
| r8 | Boemo bo bolelang, ts'ebetso ea letsatsi | 0 | 100 | % | 100 | —- |
| r9 | Mean factor, opereishene ea bosiu | 0 | 100 | % | 50 | —- |
| rd | Letsatsi le fapaneng | 0.1 | 20.0 | K | 2.0 | —- |
| St | Letsatsi le behiloeng | r1 | r2 | °C | 2.0 | —- |
d LIEKETSENG TSA MORA
| d0 | Defrost mode | 0 | 2 | – | 1 |
| 0 = defrost ea tlhaho, heater ea defrost ha e sebetse
pulsed defrost ha e khonehe 1 = ho qhibiliha ho qobelloang, heater ea defrost e butsoitse, ho phunya serame hoa khoneha 2 = ho felloa ke serame ho qobelletsoeng, heater ea defrost e kentsoeng, ho felloa ke matla hoa khoneha, ho felisoa ha serame ka nviStartUp ka SNMP |
|||||
| d1 | Pheliso ka: | 0 | 3 | – | 0 |
| 0 = ho felisoa ka mocheso,
ho felisoa ka nako ho tla hlahisa alamo 1 = ho felisoa ka nako, ho felisoa ka mocheso ho tla hlahisa alamo 2 = pele, ke eng e tlang ka lekhetlo la pele kapa mocheso, ha ho alamo 3 = ea ho qetela, ka nako le mocheso, ha ho alamo |
|||||
| d2 | Sensor ea ho felisoa ha Defrost | 0 | 1 | – | 1 |
| 0 = Sensor ea defrost e inehetseng e tlameha ho kenngoa
1 = Sensor e tsoang moeeng e sebelisetsoang ho felisa serame |
|||||
| LIEKETSENG | Min | Max | Yuniti | Def. | Tloaelo | |
| d3 | Sehatsetsi se phodileng | 0 | 1 | – | 0 | |
| 0 = ho tima, ha ho sehatsetsi se pholileng, lihitara li tima ha serame se fela
mocheso dt kapa max. nako dP eng kapa eng e khethiloeng 1 = on, pulsed defrost, dd le dH e ntse e sebelisoa, liheater lia tima ka dH ebe li buloa hape ka dH – dd |
||||||
| d4 | Defrost qalong 0 = che, 1 = e | 0 | 1 | – | 0 | —- |
| d5 | Ho lieha ho felloa ke matla ho theola serame | 0 | 180 | min | 0 | —- |
| d6 | Pompeta ho lieha | 0 | 180 | mots | 0 | —- |
| Compressor e tla sebetsa nakong ea ho lieha ha pompo ho theoha ha valve e koetsoe | ||||||
| d7 | Khaello ea metsi | 0 | 15 | min | 2 | —- |
| d8 | Ho lieha ho enta | 0 | 180 | mots | 0 | —- |
| Valve e bulehile nakong ea ho lieha ha ente ha compressor e sa sebetse | ||||||
| d9 | Batla mokhoa oa defrost
0 = tima, 1 = butle, 2 = butle mmoho le defrost e nakong |
0 | 2 | – | 0 | —- |
| dd | Phapang ea pulsed defrost | 1 | 20 | K | 2 | —- |
| dH | Sebaka sa pulsed defrost | -40 | dt | °C | 5 | —- |
| dt | Mocheso oa ho felisa serame | -40 | 90 | °C | 8 | —- |
| dP | Nako e phahameng ea defrost | 0 | 180 | min | 30 | —- |
| dI | Karohano ea defrost | 0 | 192 | h | 8 | —- |
| du | Qala ho lieha ka mor'a ho lumellana | 0 | 180 | min | 30 | —- |
F TŠOANELO LITŠOANTŠISO
| F1 | Ho qala fan ka: 0 = on | 0 | 4 | – | 0 |
| 1 = e liehile ke nako Fd, phoso ka mocheso
2 = ka mocheso Ft, phoso ka nako 3 = pele, eng kapa eng e tlang ka lekhetlo la pele kapa mocheso, ha ho alamo 4 = ea ho qetela, nako le mocheso li tlameha ho tla, ha ho alamo |
|||||
| F2 | Nakong ea ha ho pholile | 0 | 2 | – | 0 |
| 0 = ka; 1 = theoha; 2 = liehiloe ke F4; 3 = tima, ha lemati le buloa | |||||
| F3 | Nakong ea defrost 0 = on, 1 = tima | 0 | 1 | – | 0 |
| F4 | Emisa ho lieha nako | 0 | 30 | min | 0 |
| F5 | Nakong ea ho hloekisa 0 = tima, 1 = ho | 0 | 1 | – | 0 |
| Fd | Fene e lieha ka mor'a ho qhibiliha | 0 | 30 | min | 0 |
| Ft | Ka mocheso ka mor'a ho qhibiliha | -40 | 40 | °C | 0 |
C COMPRESSOR LITŠOANTŠISO
| C0 | Ho lieha ho qala ka mor'a ho tima motlakase | 0 | 15 | min | 0 |
| C1 | Nako ea potoloho | 0 | 15 | min | 0 |
| C2 | Min. nako ea ho emisa | 0 | 15 | min | 0 |
| C3 | Min. nako ea ho matha | 0 | 15 | min | 0 |
LIEKETSENG MOHOLO
| u0 | Sehatsetsi 0 = R22 1 = R134a 2 = R507 3 = R404A 4 = R407C
5 = R410A 6 = R124 7 = R744 |
0 | 7 | – | 3 |
| u1 | Ho lokisa glide / dp
Glide = boleng bo nepahetseng Khatello e theoha = litekanyetso tse mpe |
-20.0 | 20.0 | K | 0.0 |
| u2 | MOP taolo
0 = MOP e tima, 1 = MOP e butswe |
0 | 1 | – | 0 |
| u3 | Mocheso oa mocheso oa MOP | -40 | 40 | °C | 0 |
| u4 | Mocheso o chesang haholo 0 = tima 1 = mocheso o phahameng o tsitsitseng
2 = mocheso o feteletseng o fetohang |
0 | 2 | – | 1 |
| u5 | Superheat init setpoint | u6 | u7 | K | 6 |
| u6 | Superheat setpoint min. | 3 | u7 | K | 3 |
| u7 | Superheat setpoint max. | u6 | 20 | K | 15 |
| uu | Qala ho bula | 25 | 75 | % | 30 |
P ANALOGE SESOTHO PARAMETHA
| P1 | Khetho ea mofuta oa sensor ea khatello 0 = PT5-07M; 1 = PT5-18M; 2 = PT5-30M | 0 | 2 | – | 0 |
H LIEKETSENG TSE LING
| H2 | Hlahisa phihlello | 0 | 4 | – | 3 | —- |
| 0 = bohle ba holofetse (Tlhokomeliso, phihlello ea molaoli feela ka TCP/IP Ethernet
marangrang a khoneha) 1 = Keyboard e nolofalitsoe 2 = Remoutu ea IR e nolofalitsoe 3 = Keyboard le taolo e hole ea IR; Pontšo ea data ea nakoana le defrost ea letsoho e lumelletsoe. 4 = Keyboard le taolo e hole ea IR; Pontsho ya data ya nakwana e timilwe. Laola sebaka ka SEL key and manual defrost butswe. |
||||||
| H3 | Khoutu ea phihlello ea IR | 0 | 199 | – | 0 | —- |
| H5 | Password | 0 | 199 | – | 12 | —- |
Foromo ea Mean Factors A0, r8, r9
Palo ea mocheso ka mokhoa o latelang: Mocheso = Airin * (1 - Mean Factor / 100) + Airout * Mean Factor / 100
Examphanyane:
- Mean factor = 0 Mocheso = Moea o kene
- Mean factor = 100 Mocheso = Moea o tsoa
- Mean factor = 50 Mocheso = Karolelano pakeng tsa Air-in le Air-out
Likhoutu tsa Alamo
- E0 Alamo ea sensor ea khatello
- E1 Coil out alamo ea sensor
- E2 Air-in sensor alamo Khoutu ena ea Alamo e thibetsoe haeba ho se sensor ea moea e sebelisoang (A0, r8 le r9 = 100)
- Alamo ea E3 Air-out sensor Code ena ea Alamo e thibetsoe haeba ho se na sensoro ea moea e tsoang (A0, r8 le r9 = 0) le fin sensor e kentsoe (d2 = 1)
- Alamo ea Sensor ea E4 Fin Code ena ea Alamo e thibetsoe haeba ho se na sensor e sebelisoang (d2 = 0)
- Litlhaloso tsa E0 … Lialamo tsa E4: Ha ho kutlo e hoketsoeng, kapa kutlo le/kapa thapo ea kutlo e robehile kapa e khutsufalitsoe.
- Pontšo ea phoso ea Er - ha e fihlellehe
- Lintlha tse romelloang ponts'ong ha li fihlellehe.
- AH Alamo ea mocheso o phahameng
- AL Alamo ea mocheso o tlase
- Ts'ebetso ea tšohanyetso ea AE Thermostat
- Ho hloleha ha sensor ea moea, sistimi e maemong a pholileng a tsoelang pele
- Boemo ba Valofo ea AF
- Valofo e koetsoe ka lebaka la ts'ireletso ea konpresser loop e sebetsa
- Ao Superheat, ts'ebetso ea tšohanyetso ea Sensor(s) e hlolehile
- Ar Ha ho phallo ea sehatsetsi e fumanoeng
- Ha ho phallo ea sehatsetsing e fumanoeng
- Au Valve e bula 100% bakeng sa metsotso e fetang 10
- dt Ho felisoa ha serame (nako kapa mocheso)
- Ho qalisa fan e qobelloang (nako kapa mocheso)
Melaetsa
- - Ha ho na data e ka hlahisoang
Pontšo e tla bonts'a "-" qalong ea node le ha ho se na data e romelloang skrineng. - Ho Seta Botjha ho boleng ba kamehla butswe
Pontšo e tla bontša "In" ha sete ea data ea kamehla ea feme e qala. - Kopo ea Id Wink e amohetse
Pontšo e tla bontša "Id" e benyang ha kopo ea winke e amoheloa. "Id" e benyang e tla bonts'oa ponts'o ho fihlela konopo ea ts'ebeletso e tla tobetsoa, kapa sebali sa nako ea 30 min se tla fela kapa kopo ea bobeli ea wink e amoheloa. Ts'ebetso ena ke ts'ebetso feela ha o sebelisa protocol ea SNMP - OF Node ha e sebetse
Node ha e sebetse 'me ha ho na sesebelisoa se sebetsang. Sena ke phello ea taelo ea tsamaiso ea marang-rang 'me e tla etsahala bakeng sa example nakong ea ho kenya node.- dS Defrost standby
- dP Pompela fatshe
- dF Defrost cycle
- dd Ho lieha ho felloa ke metsi
- dI Defrost ente e liehang
- du Defrost ho lieha ho qala
- Cn Hloekisa
- Lialamo tsa CL li hlakotsoe
- Ho Bona Boitsebiso : WebMaqephe
TCP/IP Controller-Readme file e fumaneha ho www.emersonclimate.eu websebaka sa marang-rang ho fana ka lintlha tse qaqileng mabapi le khokahano ea TCP/IP Ethernet. Ka kopo sheba sena file haeba o hloka tlhahisoleseding e fetang dikahare tsa leqephe lena la ditaelo. EC2-352 e na le sebopeho sa puisano sa TCP/IP Ethernet se nolofalletsang molaoli hore a hokahane ka kotloloho ho PC kapa marang-rang ka boema-kepe bo tloaelehileng ba Ethernet. Molaoli oa EC2-352 o kentse WebMaqephe ho thusa mosebelisi ho bona manane a parametha habonolo a sebelisa mangolo a 'nete.
Ha ho software e khethehileng kapa hardware e hlokahalang.
- Hokela EC2-352 u sebelisa kopano ea cable ea ECX-N60 ea boikhethelo ho marang-rang kapa hub e nolofalletsang molaoli ho fumana aterese e matla ea TCP / IP. Haeba seva sa DHCP se sa fumanehe, molaoli a ka hokeloa khomphuteng a sebelisa thapo ea crossover e hoketsoeng ka kotloloho boema-kepeng ba Ethernet. Tabeng ena, aterese ea TCP / IP ea k'homphieutha e tlameha ho fetoloa ka letsoho hore e lumellane le aterese ea kamehla ea molaoli. Sheba ho TCP/IP Controller-Readme file bakeng sa lintlha tse ling.
- Bula lenaneo la sebatli sa Marang-rang k'homphieutheng 'me u kenye aterese ea kamehla ea TCP/IP ea molaoli moleng oa aterese oa sebatli sa Marang-rang: 192.168.1.101 kapa aterese e matla e tsoang ho seva sa DHCP. Sheba ho TCP/IP Controller-Readme file haeba ho hlokahala kou e khethehileng.
- Ka mor'a metsotsoana e seng mekae, leqephe la kamehla la ho beha leihlo le lokela ho hlahisoa. Haeba sebatli se sa bule leqephe la kamehla kapa se bonts'a data e sebetsang, mosebelisi o lokela ho sheba tlhophiso ea "Option" ea sebatli sa Marang-rang. Sheba ho TCP/IP Controller-Readme file.
- Maqephe a Tlhokomelo le Alamo a baloa feela, ka hona ha ho hlokahale ho kenya lebitso la mosebelisi kapa senotlolo. Lebitso la mosebelisi le phasewete li tla kopuoa ha ho etsoa kopo ea pele ho e 'ngoe ea tse ling web maqephe. Litlhophiso tsa kamehla tsa feme ke:
Username: Emerson
Password:12
- Litlhophiso tsa kamehla li ka fetoloa leqepheng la tlhophiso ea Pontšo.
- Tobetsa li-tab tse kaholimo ho leqephe la Tlhokomelo ka ho penya ka ho le letšehali ho konopo ea mouse ho kenya tse fapaneng web leqephe.
- Litekanyetso li tla bonoa ka mongolo oa 'nete hammoho le khoutu ea lenaneo joalo ka ha ho hlalositsoe lenaneng la paramethara e ka tlase.
Ka mor'a hore li-parameter li fetoloe, lenane le feletseng la litlhophiso le ka bolokoa mohopolong oa k'homphieutha 'me la sebelisoa hamorao ho kenya ho molaoli e mong. Sena se ka boloka nako e ngata ha u sebelisa li-controller tse ngata, 'me ha nako e ntse e feta, ho ka etsoa laeborari e nang le lethathamo la lisebelisoa tsa lisebelisoa tse fapaneng.
Hape hoa khoneha ho bonts'a data ea graphical e phelang ho tsoa ho molaoli. Ho ekelletsa moo, ho sa feleng matsatsi a 30 log file e nang le mocheso oa taolo ka nako ea metsotso e 15 e bolokoa mohopolong o sa fetoheng hore o fetisetsoe hamorao ho sebelisoa FTP ho komporo. The log file e ka romelloa ka har'a lenaneo le tloaelehileng la spreadsheet joalo ka Excel. Sheba ho TCP/IP Controller-Readme file bakeng sa tlhaloso e feletseng ea likarolo tse fumanehang bakeng sa letoto la TCP / IP la balaoli.
Emerson Climate Technologies GmbH www.nakhongolin.eu Am Borsigturm 31 I 13507 Berlin I Germany Letsatsi: 13.06.2016 EC2-352_OI_DE_R07_864925.doc
FAQ'S
Nka fumana lintlha tse felletseng hokae ka molaoli oa EC2-352?
Boitsebiso bo eketsehileng bo ka fumanoa ho Buka ea Mosebelisi.
Litokomane / Lisebelisoa
 |
EMERSON EC2-352 Pontšo ea Case le Coldroom Controller [pdf] Bukana ea Mosebelisi EC2-352 Display Case le Coldroom Controller, EC2-352, Pontšo ea Case le Coldroom Controller, Case le Coldroom Controller, Coldroom Controller, Controller |
