Echo SRM-225 U-handle Combo Kit

TLHOKOMELO

U tlameha ho kenya Barrier Bar kapa U-Handle Kit le likarolo tsohle tsa Blade Conversion tse bontšitsoeng litaelong tse latelang pele u sebelisa yuniti ena ka li-blades, ho seng joalo kotsi e mpe e ka hlaha.

BOHLOKOA: Haeba ho sebelisoa lihlooho tse sa tloaelehang tsa monofilament, li-blades tsa METAL / PLASTIC kapa lihoai joalo-joalo, li sebelisoa, CARBURETOR E LOKELA HO HLAHALA TSELA kapa tšenyo e khōlō ea enjene e ka etsahala. Sheba “Phetoho ea Carburetor” Bukeng ea Opereishene ea Yuniti.

SRM/PAS/SB LEHLABA LE TLHOKOMELA TATAISO

SEBELISA MAHLABATSANA		Pro Maxi-Cut Grass / Weed Plastic Cutters	Polasetiki e thata ea Tri-Cut Joang / Lehola la Lehola	Tšepe Tri-Cut/8 Tooth Grass/Lehola la Lehola	Tšepe 80T Brush Lehare Metal 22T Hlakola Saw Lehare
U tlameha ho kenya likarolo tsena!	Tšoara	Loop Handle, w/kapa w/o Barrier Bar	Loop Handle w/Barrier Bar, kapa U-Handle	Loop Handle w/Barrier Bar, kapa U-Handle	U-Handle
	Tšilafalo Shield	Thebe ea tšepe	Thebe ea tšepe	Thebe ea tšepe	Thebe ea tšepe
	Harness	Sebono sa Mahetla	Sebono sa Mahetla	Sebono sa Mahetla	Boma ba Mahetla****
	Blade Mounting Hardware	Plate e ka Holimo le Washer ea Flat	Letlapa le ka Holimo le Mohope oa Glide	Lipoleiti tsa Lehare tse ka Holimo/ka Tlase**	Lipoleiti tsa Lehare tse ka Holimo/ka Tlase**
		Hex Nut	Hex Nut	Hex Nut	Hex Nut
		Pin e Ncha ea Cotter***	Pin e Ncha ea Cotter***	Pin e Ncha ea Cotter***	Pin e Ncha ea Cotter***

 TLHOKOMELO

• U SE KE UA KENYA BLADES HO GT (CURVED SHAFT) MODEL TRIMMERS
• Bophara ba Arbor Plate ea Upper Blade Plate bo tlameha ho ts'oana le bophara ba mahare a tšepe.
• Ho hlokahala pini e ncha ea cotter nako le nako ha ho kengoa lehare.
• Li-brushcutters tse fetang 16.5 lbs (7.5kg) boima bo ommeng (boima ba mafura) li hloka marapo a mabeli a mahetleng.

Litaba

• 1, kopano ea U-handle
• 1, borakete e ka tlase ea u-hand (lihalofo tse 2)
• 1, Harness Clamp w/ring
• 1, 5 x 12 limilimithara bolt
• 1, 8 x 55 limilimithara bolt
• 1, Washer e chitja
• 1, Square nut
• 2, likhechana tsa mohala oa Throttle
• 3, 5 x 25 limilimithara liboutu
• 1, hip pad
• 1, Mahetla a Mahetla
• 1, Letlapa le ka Holimo, 20 limilimithara
• 1, Letlapa le ka Tlase
• 1, Thebe ea tšepe
• 1, Bracket
• 3, 5 x 10 mm li-screw (sekoahelo sa thebe)
• 2, 5 x 8 mm likurufu (brakete ho thebe)
• 4, 5 limilimithara linate
• 4, 5 limilimithara lilockwashers
• 1, M10 x 1.25 LH Nut
• 10, Lithako tse arohaneng
• 1, 10 limilimithara molaleng
• 2, 5 x 35 limilimithara likurufu

Ho kenya

Lisebelisoa li Hlokahala: 8mm x 10mm Open End Wrench, T-wrench, Torx T-27 L-Wrench

1. Koala khama 'me u tlose sefe ea moea le sekoahelo.
2. Hakolla likhoele tse emisang ho khantša (A) le (B).
3. Lokolla linate (C) 'me u tlose khokahano ea throttle ho tsoa ho bracket ea carburetor (D).
4. Tlosa mohala oa throttle o ka hare (E) ho tloha ho carburetor swivel (F).
5. Lokolla tse peli (2) drive shaft clamp liboutu (G) ho enjene drive shaft clamp.
6. Hula kopano ea shaft ea drive ho tloha ho clutch case.
7. Lokolla li-screw tse peli (2) tse ka morao (H) 'me u hule mohele o ka morao ho tsoa kopanong ea shaft ea drive.
8. Lokolla likurufu tse 'ne (4) (I) 'me u tlose mohele o ka pele.
9. Kenya sekoere nut (J) ka har'a borakete ea mohele o ka tlaase (K) 'me u behe borakete holim'a shaft ea drive 400 mm (15 3/4 in.) ho tloha pheletsong ea enjene ea shaft ea koloi.
10. Sireletsehile ka bracket e ka tlaase ea ho tšoara clamp (L) le liboutu tse tharo (3) 5 x 25 mm.
11. Sebaka sa marang-rang clamp (M) 220 mm (8-5 / 8 in.) ho tloha qetellong ea enjene ea kopano ea shaft ea koloi. Kenya bolt ea 5 x 12 mm, empa U SE KE UA tiisa ka nako ena.
12. Kopanya ka hloko kopano ea shaft ea drive ho enjine ho etsa bonnete ba hore shaft ea kahare ea drive e kenella ka har'a sokete ea clutch.
13. Tiisa tse peli (2) koloi shaft clamp liboutu (G) ka mokhoa o sireletsehileng.
14. Kenya U-Handle e ka holimo le borakete ka har'a bracket e tlase 'me u sireletsehe ka e le 'ngoe (1) 8 x 55 mm bolt (N) le washer e kholo e chitja.
15. Khokahano ea "route throttle" le kopano ea lead lead ka mor'a bracket ea U-Handle le clip ho khanna shaft joalo ka ha ho bonts'itsoe.
16. Beha mohala o ka hare oa throttle (E) ka mokoting o moholo oa carburetor swivel (F).
17. Tlosa nate (C) 'me u behe qetellong ea khokahanyo ea throttle ka har'a bracket slot. Nate e tiisang menoana (C).
18. Lekola throttle bakeng sa tokoloho ea ho tsamaea le hore li-throttle tse bulehileng / tse tlase tse sa sebetseng li fetotsoe hantle. Haeba phetoho e ke ke ea finyelloa ka ho lokisa linate (C, O), ikopanye le Echo Dealer ea hau bakeng sa mokhoa o nepahetseng oa tokiso. Tiisa nate (C).
19. Hokela li-ignition stop lead (A,B) ho tloha ho throttle cable tubing ho isa ho tse 2 tsa lignition lead (A,B) enjeneng.
20. Ho khantša ho sireletsehileng ho lebisa khahlano le ntlo ea enjine e nang le likarolo (P, Q).
21. Kenya sefe ea moea le sekoahelo

Kenya Hip Pad (Boikhethelo)

1. Hokela hip pad ho tlama joalo ka ha ho bonts'itsoe.

kenya tšepe thebe

Lisebelisoa Tse Hlokehang

• 8 x 10 limilimithara Open-end Wrench, Torx T-27 L-Wrench, T-wrench, Sesebelisoa sa ho notlela

Likarolo Tse Hlokehang: Thebe ea tšepe, Bracket ea Shield,

• 3 - 5 x 10 mm li-screw (thebe ea tšepe ho matlo a lisebelisoa).
• 2 – 5 x 8 mm screws, 2 – 5 mm nuts, 2 – 5 mm lock-washers, (bracket to thebe).
• 2 – 5 x 35 mm dikurufu, 2 – 5 mm nuts, 2 – 5 mm lockwashers (bracket to gear housing)

1. Haeba e kentsoe tlosa hlooho ea nylon, poleiti e ka holimo ea ho lokisa, letlapa la thebe, le thebe ea polasetiki.
   1. Lokisetsa lesoba le notlelang poleiting e kaholimo le notch moeling oa ntlo ea lisebelisoa ebe u kenya sesebelisoa sa ho notlela hlooho (A).
   2. Tlosa hlooho ea mohala (B) ka ho e fetola ho fihlela hlooho e tima ka ho feletseng.
   3. Tlosa sesebelisoa sa ho notlela.
   4. Tlosa likurufu tse tharo tse ts'oereng thebe (D) le thebe ea polasetiki (C) ho kenya lisebelisoa.
   5. Boloka hlooho ea mohala (B), poleiti ea ho lokisa e ka holimo (E), letlapa la thebe, le thebe ea polasetiki (C) bakeng sa ho sokolohela ho ts'ebetso ea hlooho ea nylon.
2. Hokela borakete (F) ho thebe (G) ebe o hokela thebe tlase ho ntlo ea lisebelisoa (H) ka hardware e fanoeng.
3. Tlosa gearcase clampli-ing screws (I) ebe o hokela borakete (F) ka mokhoa o hlephileng ho gearcase (H) e nang le likurufu tse 2 - 5x35mm, linate le li-lockwasher tse fanoeng ka har'a khiti.
4. Tiisa lisebelisoa tsohle tsa thebe.

kenya lehare la boikhethelo

Lisebelisoa Tse Hlokehang

• Sesebelisoa sa ho notlela, T-Wrench.

Likarolo Tse Hlokehang: Letlapa le ka Holimo le nang le mofofisi oa limilimithara tse 20, Letlapa le ka Tlase, 10 mm Nut, 2 x 25 mm Split Pin, Lehare.

1. Kenya molala oa shaft (A) ebe poleiti ea ho lokisa e ka holimo (B) holim'a shaft ea PTO.
2. Kenya Blade (C) holim'a sefofane sa sefofane. Li-blades li tlameha ho kenngoa e le hore motsu o potolohang holim'a lehare o shebane le mokotla oa gear. Lehare le sireletsehileng le nang le poleiti e tlase ea ho lokisa (D), le linate tsa 10 mm (E). Fetola linate ka tsela e fapaneng ho PTO shaft ho tiisa.
3. Hlophisa lesoba holim'a poleiti e ka holimo le notch ka har'a matlo a lisebelisoa, 'me u kenye sesebelisoa sa ho notlela (F) ho thibela shaft e petsohileng hore e se ke ea reteleha. Motsu o holim'a lisebelisoa tsa matlo a marang-rang o fihla holimo. Tiisa linate tsa 10 mm ka mokhoa o sireletsehileng.
4. Kenya phini e arohaneng (G) ka mokoting ho PTO shaft, 'me u kobe maoto a phini ho potoloha shaft ka tsela e fapaneng le oache ho boloka 10 mm nut.
   • BOHLOKOA: Le ka mohla u se ke ua sebelisa hape pini e arohaneng - kenya pini e ncha e arohaneng nako le nako ha lehare le kenngoa kapa le nkeloa sebaka.
5. Tlosa sesebelisoa sa ho notlela.

Tekanyo le ho Fetola Yuniti

1. Lokolla marapo clamp nsete.
2. Apara marapo 'me u kopanye yuniti ho marapo.
3. Slide harness clamp (H) holimo kapa tlase ho fihlela tekanyo ea yuniti e nang le hlooho e ka bang 50-75 mm (2 -3 in.) ho tloha fatše.
4. Tiisa marapo clamp nsete.
5. Lokolla sehlopha sa U-Handle se kaholimoamp li-screw (I), le boemo ba U-Handle bakeng sa ts'ebetso e ntle.
6. Tiisa U-Handle clamp lisekere le 8 mm clamp bolt ka mokhoa o sireletsehileng.

HLOKOMELA: Haeba ho na le Boemo ba Tšohanyetso, sethima/sethara se ka lokolloa ho tloha ho marapo ka ho hula molaleng o tsoang kapele.

echo tšehetso ea sehlahisoa sa bareki

Haeba u hloka thuso kapa u na le lipotso mabapi le ts'ebeliso, ts'ebetso kapa tlhokomelo ea sehlahisoa sena u ka letsetsa Lefapha la Tšehetso ea Sehlahisoa sa Bareki la ECHO ho 1-800-673-1558 ho tloha ka 8:30 hoseng ho isa ho 4:30 mantsiboea (Nako e Tloaelehileng e Bohareng) Mantaha ho isa Labohlano. Pele o letsetsa, ka kopo tseba mofuta le nomoro ea serial ea yuniti ea hau ho thusa Moemeli oa Ts'ehetso ea Sehlahisoa sa Bareki.

ECHO, EKETSEHILENG

• 400 OAKWOOD ROAD LAKE ZURICH, IL 60047 USA
• MOFONO: 1-800-673-1558
• www.echo-usa.com

Echo SRM-225 U-handle Combo Kit User Manual

Litšupiso

• Bukana ea Mosebelisi