AMDP 2020-2022 6.7L Power Programmer Powerstroke User Guide

A: Che, thapo ea katoloso ea terata ea lamunu ke FEELA bakeng sa ts'ebetso ea ho notlolla L5P Duramax ECM 'me ha ea lokela ho sebelisoa bakeng sa lits'ebetso tsa Powerstroke.

KA KOPO U BALA LITAELO KA HLOKO PELE U SEBELISA

BOHLOKOA HO BASEBELISI BOHLE

E kenyelelitsoe ho Power Programmer kit ke thapo e khuts'oane ea katoloso e nang le terata ea lamunu. Kopano ena ea cable FEELA e tla sebelisoa ts'ebetsong ea ho notlolla L5P Duramax ECM! E SE KE ea sebelisoa bakeng sa lits'ebetso tsa Powerstroke!

Mehato ea pele ea ho sebelisa Auto Flasher

U tlameha ho ba le Windows 10 kapa komporo e betere ho sebelisa software ea Auto Flasher.

Mohato oa 1: Khoasolla software ea Power Programmer ho tsoa ho https://amdptuning.ca/pages/instructions

Hata 2: Khoasolla Power Programmer USB Drivers ho tloha https://amdptuning.ca/pages/instructions
Hata 3: Ho Lits'oants'o komporong ea hau, Bula, Ntša, Matha, 'me u kenye VCP USB Drivers 64bit. Latela litlhahiso ho fihlela qetellong.

Mohato oa 4: Ho jarolla khomphuteng ea hau, Bula, Matha, 'me u kenye Auto Flasher. U kanna ua tlameha ho tima software ea anti-virus hore u tsebe ho kenya software ea Auto Flasher.
Mohato oa 5: Bula Auto Flasher, e kanna ea u khothaletsa ho ntlafatsa mofuta o mocha. Tobetsa "E" 'me u latele likhothaletso ho ntlafatsa mofuta oa morao-rao.

Mohato oa 6: FEELA plug ho Power Programmer module (lebokose le letšo) ho USB ka nako ena, ha ho na likhoele tse ling.
Hata 7: Tobetsa Cable> Connect> Cable> Update Firmware. Latela litaelo tsa potoloho ea USB ho ntlafatsa firmware.

Hata 8: Hang ha firmware e se e le teng, tobetsa Cable > Connect. Joale o lokela ho bona ID ea CABLE e hlaha kaholimo ho le letona la lenaneo 'me u se u loketse ho ea!

Tokiso ea Enjine ea Powerstroke Feela

Mohato oa 1: Fumana PCM ka lehlakoreng la Passenger side firewall 'me u hakolle lihokelo TSOHLE tse 3.

Mohato oa 2: Hokela thapo ea motlakase ho betri ea koloi (etsa bonnete ba polarity e nepahetseng).
Mohato oa 3: Hokela Power harness ho AMDP Power Programmer, ebe o hokela sehokelo sa PCM se fanoeng ho plug ea PCM ea bapalami ka ho fetisisa koloing.

Mohato oa 4: Hokela AMDP Power Programmer ho Laptop e thehiloeng ho Windows ka software e boletsoeng pejana e kentsoeng.
Hata 5: Bula software ea AutoFlasher, khetha "Cable", ebe u khetha "Connect". Haeba khokahano e atlehile tsoela pele ho

Bohato ba 6, haeba e sa kenye Bakhanni ba USB hape 'me u hlahlobe likhokahano tsa USB.
Mohato oa 6: Khetha "Service Mode", ebe "Power On". Molaetsa "Powering on module" o lokela ho hlaha.

Mohato oa 7: Khetha "Service Mode", ebe "Identify". Netefatsa hore ho buisanoa le PCM. Haeba ho se joalo, hlahloba likhokahano tsa matla 'me u phete Mohato oa 6. Cable S/N, ECU S/N le VIN li hloka ho romelloa ho sales@amdieselperformance.ca ka nomoro ea hau ea odara ea AMDP le eo u mo laetseng hore a fumane tokiso e rekiloeng. Ho kopitsa nomoro e 'ngoe le e' ngoe ka ho le letona tobetsa Ctrl-V ho lengolo-tsoibila.
Hata 8: Hang ha u se u fumane lipina ka imeile, li boloke khomphuteng ea hau. Pheta

Mehato ea 1-7 haeba u khaolitse koloing.
Mohato oa 10: Khetha "Service Mode", ebe "Ngola", ebe "ECU", khetha file o rometsoe ka lengolo-tsoibila pele. Ts'ebetso ea tokiso e tla qala joale. Ha e se e phethiloe o ka hakolla likhokahano tsohle tsa AMDP Power Programmer mme o hokela hape lihokelo tsa PCM tsa feme.

Mohato oa 11: Netefatsa hore koloi ea qala 'me ha ho na likhoutu tsa DTC kapa melaetsa ea dash e teng. Haeba ho na le letho le teng ka kopo ikopanye le Tech support.

Powerstroke Hlakola Feela Tokiso ea Enjine

Ka kopo Hlokomela: 2022 Hlakola Feela Tokiso E TLAMEHA ho ba le EGR le Throttle Valves sebakeng mme e hokahane ka nako ena.

Mohato oa 1: Fumana PCM ka lehlakoreng la Passenger side firewall 'me u hakolle lihokelo TSOHLE tse 3.
Mohato oa 2: Hokela thapo ea motlakase ho betri ea koloi (etsa bonnete ba polarity e nepahetseng).
Mohato oa 3: Hokela Power harness ho AMDP Power Programmer, ebe o hokela sehokelo sa PCM se fanoeng le plug ea Passenger side PCM koloing.
Mohato oa 4: Hokela AMDP Power Programmer ho Windows based Laptop ka software e boletsoeng pejana e kentsoe.
Hata 5: Bula software ea AutoFlasher, khetha "Cable", ebe u khetha "Connect". Haeba khokahano e atlehile tsoela pele ho Mohato oa 6, haeba e sa kenye li-Driver tsa USB hape 'me u hlahlobe likhokahano tsa USB.
Mohato oa 6: Khetha "Service Mode", ebe "Power On". Molaetsa "Powering on module" o lokela ho hlaha.
Mohato oa 7: Khetha "OBD", ebe "Identify". Netefatsa hore ho buisanoa le PCM. Haeba ho se joalo, hlahloba likhokahano tsa motlakase 'me u phete Mohato oa 6.
Mohato oa 8: Khetha "OBD", ebe "Fumana VIN". The Cable S/N, ECU S/N le VIN li hloka ho romelloa ho sales@amdieselperformance.ca ka nomoro ea hau ea odara le hore na o e laetse mang ho amohela tokiso e rekiloeng. Ho kopitsa nomoro e 'ngoe le e' ngoe ka ho le letona tobetsa Ctrl-V ho lengolo-tsoibila.
Hata 9: Hang ha u se u fumane lipina ka imeile, li boloke khomphuteng ea hau. Pheta Mehato ea 1-7 haeba u khaolitse koloing.
Mohato oa 10: Khetha "OBD", ebe "Ngola", ebe "ECU", khetha khetho file o rometsoe ka lengolo-tsoibila pele. Ts'ebetso ea tokiso e tla qala joale. Ha e se e phethiloe o ka hakolla likhokahano tsohle tsa AMDP Power Programmer mme o hokela hape lihokelo tsa PCM tsa feme.
Mohato oa 11: Netefatsa hore koloi ea qala 'me ha ho na likhoutu tsa DTC kapa melaetsa ea dash e teng. Haeba ho na le letho le teng, ka kopo ikopanye le tšehetso ea Tech.

Powerstroke Power Engine Tuning & PCM Swap

Mohato oa 1: Hokela AMDP Power Programmer ho OBD2 Port ea koloi le lifensetere tse thehiloeng laptop ebe u bula senotlolo ho boemo ba Run/On.
Mohato oa 2: Ho software ea Autoflasher, khetha "Cable" -> "Connect". Haeba khokahano e atlehile, tsoela pele ho Mohato oa 5.
Mohato oa 3: Khetha "OBD" -> "AsBuilt" -> "Bala". Ka fensetere e hlahang, khetha "ECU" ebe u khetha "Enter". Boloka data ea AsBuilt (didsRead).
Mohato oa 4: Khetha "Cable" -> "Hakolla". Hakolla Programmer ho tloha OBD2 Port.
Hata 5: Kenya PCM e Ncha 'me u kopanye Programmer ho PCM ka harness e fanoeng ea PCM. Netefatsa hore likhokahano tse ling kaofela tsa PCM li hakotsoe.
Mohato 6: Khetha "Service Mode" -> "Bala EE". Boloka the file (EE_E bale).

Mohato oa 7: Romella Cable S/N le ECU S/N ka ho tobetsa ka ho le letona ho e 'ngoe le e' ngoe ebe u e manamisa ka lengolo-tsoibila le nomoro ea Order, VIN le hore na u e laetse mang ho amohela tokiso ea hau.
Mohato 8: Khetha "Service Mode" -> "Power Off".
Mohato oa 9: Khetha "Cable" -> "Hakolla"

Mohato oa 10: Ha u se u fumane pina ea enjene, khetha "Cable" -> "Connect", ebe u khetha "Service Mode", "Ngola", Khetha pina.
Mohato 11: Ha Flash Atleha hlaha, Khetha "Service Mode" -> "Power Off".
Mohato oa 12: Khetha "Cable" -> "Hakolla"

Mohato oa 13: Hokela PCM e Ncha ho Harness ea Koloi
Mohato oa 14: Hokela Programmer ho OBD2 Port ebe o bula senotlolo ho On/Run Position.
Mohato oa 15: Khetha "OBD" -> "AsBuilt" -> "Ngola", khetha data ea AsBuilt e bolokiloeng pele (didsRead), khetha "ECU", ebe u khetha "Enter".

Mohato 16: Khetha "OBD" -> "Misc Routines" -> "Configuration Relearn", khetha "ECU", ebe Khetha "kena". Latela likhothaletso tsa metsotsoana e 30 bakeng sa Key On, ebe O koala. Hang ha o qetile ho bulela hape.
Mohato 17: Mohato 6: Khetha "OBD" -> "Misc Routines" -> "PATs" -> "BCM EEPROM Bala". Boloka the file. Haeba ho bala ha BCM ho nka nako e telele ho feta metsotso e 10, tlosa likhoele tsohle ho Programmer ebe u koala software ea Autoflasher. Tsamaisa konopo ea ho khantša, bula software hape, kopanya Lenaneo hape ebe u leka hape.
Mohato 18: Khetha "OBD" -> "Misc Routines" -> "PATs" -> "PATs Reset". Khetha "E" ha u botsoa "Na u na le EEPROM e baloang ka BCM joalo ka ha sena se entsoe pejana. Khetha "E" ha u botsoa hore na u na le EEPROM e balang ECU joalo ka ha sena se entsoe pejana. Khetha BCM EEPROM Read, ebe u khetha EERead. Ha u khothalletsoa ho "Cycle Key", koala ebe u khutlela ho Run/On ha u khothalletsoa. Hang ha PATs e tsosolosa molaetsa o atlehileng o hlaha o ka qala koloi.

Tokiso ea phetisetso ea Powerstroke

Mohato oa 1: Hokela thapo e fanoeng ea OBD2 ho AMDP Powerstroke Programmer le boema-kepe ba koloi ba OBD2. Fetolela senotlolo sa koloi sebakeng sa Matha/On.
Mohato oa 2: Hokela AMDP Power Programmer ho Windows e thehiloeng Laptop.
Hata 3: Bula software ea AutoFlasher, khetha "Cable", ebe u khetha "Connect". Haeba khokahano e atlehile tsoela pele ho Mohato oa 4, haeba e sa kenye li-Driver tsa USB hape 'me u hlahlobe likhokahano tsa USB.

Mohato oa 4: Khetha "OBD", ebe "Identify". Khetha "TCU" ebe "Enter". TCU S/N e tla qala ka “5”. Netefatsa hore TCM e buisana le eona. Haeba ho se joalo, hlahloba likhokahano tsa motlakase 'me u phete Mohato oa 3.
Mohato oa 5: Khetha "OBD", ebe "Fumana VIN". Cable S/N, TCU S/N le VIN li hloka ho romelloa ka lengolo-tsoibila ho sales@amdieselperformance.ca le nomoro ea hau ea odara le hore na u e odara ka mang hore u fumane tokiso e rekiloeng. Ho kopitsa nomoro e 'ngoe le e' ngoe ka ho le letona tobetsa Ctrl-V ho lengolo-tsoibila.
Hata 6: Hang ha u se u fumane lipina ka imeile, li boloke khomphuteng ea hau. Pheta Mehato ea 1-4 haeba u khaolitse koloing.

Mohato oa 7: Khetha "OBD", ebe "Misc Routines", ebe "Clear Tans Adaptive Learn". Sena se tla seta botjha Transmission KAM (Keep Life Memory)
Mohato oa 8: Khetha "OBD", ebe "Ngola", ebe "TCU", khetha TCM Tune. file o rometsoe ka lengolo-tsoibila pele. Hang ha tokiso e phethiloe, koala konopo ebe o bulela, o ka hakolla likhokahano tsohle tsa AMDP Powerstroke Programmer.
Mohato oa 9: Qala koloi 'me u netefatse hore ha ho na likhoutu tsa DTC kapa melaetsa ea dash e teng. Haeba ho na le letho le teng ka kopo ikopanye le Tech support.

Duramax L5P ECM Notlolla

Mohato oa 1: Hokela AMDP Powerstroke Programmer boema-kepeng ba koloi ea OBD2 ka thapo e fanoeng ea L5P Unlock (thapo e khuts'oane ea terata ea lamunu) le thapo ea OBD2.
Mohato oa 2: Kenya terata ea lamunu ka har'a Fuse ea ECM. Bakeng sa likoloi tse 17-19, ke Fuse 57 (15A). Bakeng sa likoloi tse 20+, ke fuse 78 (15A).
Hata 3: Hokela AMDP Powerstroke Programmer ho komporo e thehiloeng ho Windows.

Mohato oa 4: Fetola senotlolo sa Koloi sebakeng sa Matha/On (O seke oa qala koloi).
Hata 5: Bula software ea AutoFlasher, Khetha "Cable" ebe "Connect". Haeba khokahano e atlehile tsoela pele ho Mohato oa 6, haeba e sa kenye li-Driver tsa USB hape 'me u hlahlobe likhokahano tsa USB.
Mohato oa 6: Khetha "OBD", "OEM", ebe u khetha "GM". Khetha "OBD", ebe "Power On". Khetha "OBD", ebe "Identify". Kopitsa 'me u boloke boitsebiso ba Bootloader le Segment bo fumanoeng.

Hata 7: Khetha "OBD", ebe "Power On". Khetha "OBD", "Tlosa", Etsa ho notlolla". Mokhoa oa ho notlolla o lokela ho qala joale. Haeba software e kopa ho fetisa karolo, khetha e, 'me u kenye linomoro tsa karolo tse bolokiloeng ho Mohato oa 6.
Mohato oa 8: Hang ha ts'ebetso ea ho notlolla e felile, khetha "OBD", ebe "Power Off". Khetha "Cable", ebe "Haola". Hona joale o ka khaola Programmer koloing ebe o kenya fuse ea ECM e tlositsoeng Mohato oa 2.
Mohato oa 9: Qala koloi. Haeba koloi e sa qale, ka kopo ikopanye le Tech Support. ECM e se e notletsoe 'me e se e loketse ho lokisoa ho sebelisoa HP Tuners le MPVI ka kotloloho Boema-kepeng ba OBD.

Ho eketsa Likoloto tsa License tsa VIN

Hata 1: Hokela AMDP Powerstroke Programmer ho komporo e thehiloeng ho Windows.
Hata 2: Bula software ea AutoFlasher.
Mohato oa 3: Khetha "Credits", ebe "Sheba Credits".

Hata 4: The Credits lokela ho ka tsela e iketsang eketsoa. Haeba u sa etse bonnete ba hore u hokahane le Marang-rang 'me u phete mehato ea 1-3.

Litokomane / Lisebelisoa

AMDP 2020-2022 6.7L Power Programmer Powerstroke [pdf] Bukana ea Mosebelisi
2020-2022 6.7L Power Programmer Powerstroke, 2020-2022, 6.7L Power Programmer Powerstroke, Power Programmer Powerstroke, Programmer Powerstroke, Powerstroke

Litšupiso

Bukana ea Mosebelisi

AMDP 2020-2022 6.7L Power Programmer Powerstroke

Tlhahisoleseding ya Sehlahiswa

Lipotso Tse Botsoang Hangata