User Manual
SpeedyBee F745 35A BLS AIO
Contents
hide
Part 1 – OverView
Specifications
Overview
| Product Name | SpeedyBee F745 35A BLS AIO |
| Power Input | 3S – 6S Lipo |
| Mounting | 25.5 x 25.5mm, 3mm hole diameter |
| Dimension | 36.5mm(L) x 36.5mm(W) x 7mm(H), recommended for quads at 3.5″ or above |
| Weight | 10.1g |
FC
| MCU | STM32F745 |
| IMU(Gyro) | MPU6000 |
| USB Connection | Need to solder a USB TYPE-C module to D+,D-,GND pads. |
| Barometer | BMP280 |
| OSD | Supported |
| BLE Bluetooth | Supported. Used for parameter configuration |
| Flash FC Firmware Wirelessly | Supported |
| Download/Analyze Blackbox | Supported |
| DJI Air Unit 6-pin Connector | Built-in. |
| Flash(for BlackBox) | 8MB |
| Current Sensor | Supported. Scale=256 |
| BetaFlight Camera Control Pad | Yes(CC pad) |
| 5V Output | 4 groups of 5V output. The total current load is 2.5A. |
| 9V Output | None |
| ESC Signal Pads | M1 – M4 |
| UART | Full UART * 4(UART1, UART2, UART3,UART4) |
| ESC Telemetry UART | None |
| I2C | Supported. |
| LED Pad | Used for WS2812 LED |
| Buzzer | BZ+ and BZ- pad used for 5V Buzzer |
| BOOT Button | Used to enter DFU mode |
| RSSI Input | Not supported |
| SmartPort | Use any TX pad of UART for the SmartPort feature. |
| Supported Flight Controller | BetaFlight(Default) |
| Firmware Firmware Target Name |
SPEEDYBEE F745AIO |
ESC
| Power Input | 3-6S LiPo |
| Continuous Current | 35A * 4 |
| Burst Current | 45A(5S) |
| ESC Protocol | DSHOT300/600 |
| Power Output | VBAT |
| Current Sensor | Supported(Sacle=256) |
| Firmware | BLHeli_S JH40 |
Dimensions
Package
- SpeedyBee F745 35A BLS AIO x 1
- 35V 470uF Capacitor x 1
- XT30 Power Cable(Length: 7cm) x 1
- 6pin DJI Air Unit cable x 1
- External USB Port module(Wire Length: 5mm) x 1
- M2(Diameter) * 12mm(Length) Screw x 5
- M2(Hole Diameter) * 6.6mm(Height) Anti-vibration Silicone Grommets x 5
- M2 Silicone O-Ring x 5
- M2 Nylon Hex Nut x 5
- Manual & App Download Card x 1
Layout
- LED Indicator Definition
- GREEN LED – Solid Green indicates Bluetooth is connected.
- BLUE LED Flight controller status light which is controlled by the flight controller firmware.
- BOOT Button
Only if the flight controller gets bricked , please follow these steps to re-flash firmware for it:
- Hold the BOOT button (the only button on the FC), and power to FC at the same time, then the FC will enter DFU mode.
- Open the SpeedyBee app, go to the FC Firmware Flashing page, and perform the Firmware Flashing as prompted.
Part 2 – Flight Controller
Wiring Diagram
USB-C Module*
* Due to the size limitation, there’s no 5V output from the FC to the USB-C module, so you need to power the AIO with a battery before you connect the AIO flight controller to your computer with a USB-C cable.
App
- Get the SpeedyBee App
Search `SpeedyBee’ on Google Play or App Store. Or download the Android .apk file on our website: https://www.speedybee.com/download.
Connect the App
FC Firmware Update
BlackBox Analyzer
Part 3 – ESC
Connection with Motors & Power Cable
Note: In order to prevent the AIO from being burnt out instantaneous voltage spikes on powering up, it is strongly recommended to use the Low ESR capacitor in the package.
ESC Configuration
ESC Firmware Update
- You could flash both BLHeli_S and Blue Jay firmware for this ESC.
You need to pulg in the battery to the AIO and then connect a USB cable between the AIO and your PC. Then flash ESC firmware (BLHeli_S or Blue Jay) in the following online configurator: https://esc-configurator.com/
Note: ESC Type should be set as ‘J-H-40’.
Documents / Resources
 |
SpeedyBee F745 35A BLS AIO Flight Controller [pdf] User Manual F745 35A BLS AIO Flight Controller, F745 35A BLS AIO, Flight Controller, Controller |
 |
SpeedyBee F745 35A BLS AIO Flight Controller [pdf] User Manual F745 35A, F745 35A BLS AIO Flight Controller, AIO Flight Controller, Flight Controller, Controller |
 |
SpeedyBee F745 35A BLS AIO Flight Controller [pdf] User Manual F745 35A BLS AIO, F745 35A BLS AIO Flight Controller, Flight Controller, Controller |
