SONICAKE QME-10 Multi Effects Processor User Manual

SONICAKE QME-10 Multi Effects Processor

Product Usage Instructions

1. LCD Display: The 1.77-inch color screen displays preset information, battery level, BT status, and other operational details.
2. Device Controls: Use the VALUE/VOL knob to turn on the device or access the options menu. Press or turn the knob to adjust the parameters.
3. Presets and Effects: Use the navigation buttons to switch presets, effect modules, and various options.
4. Tuner and Loop Menu: In the main menu, press specific buttons to access the tuner or loop menu. Return to the main menu by pressing other buttons simultaneously.
5. Input and Output: Connect your instrument via the 1/4 TS mono input and headphones, amps, or pedals to the 1/4 TRS stereo output.
6. USB Connectivity: Use the USB Type-C port to connect to a mobile phone or computer for recording and firmware upgrades. It also serves as a power supply and charging port.

FAQs

Specifications

• Technical Specifications
  • A/D/A Converter: 24-bit
  • Sampling Frequency: 44.1 kHz
  • SNR: 103dB
  • Maximum Simultaneous Effects: 9
  • Preset Memory: 100 Presets Slots, 50 Factory Presets
• Analog Input Connections
  • IN: 1/4″ (6.35mm) Unbalanced (TS), 1MΩ
• Analog Output Connections
  • OUT (PHONES): 1/4″ (6.35mm) Stereo (TRS), 100Ω
• Digital Connections
  • USB Port: USB 2.0 Type C Port
• USB Recording Specification
  • Sample Rate: 44.1 kHz
  • Bit Depth: 16-bit
• Size and Weight
  • Dimensions: 103.5mm (W) × 85mm (D) × 28.5mm (H)
  • Unit Weight: 194g
• Power
  • Power Requirements: USB Type-C, DC 5V
  • Built-in Lithium Battery: 1000mAh

www.sonicake.com.

Description

1. 1.77″ LCD color screen, to display preset information, battery level, BT status, and other operational information
2. Hold to turn on the device or enter the options menu; turn or press the knob to select or adjusts parameters
3. Press “◀” / “▶” to switch presets, switch effect modules and various options
   • In the main menu:
     Press “◀ ” + “▶” at the same time to turn on the TUNER; hold “◀” + “▶” at the same time to enter the loop menu
   • In a non-main menu:
     Press “◀” + “▶” at the same time to return to the main menu
4. 1/4″ (6.35mm) TS mono input for plugging in your instrument
5. 1/4″ (6.35mm) TRS stereo output for connecting headphones, amps, pedals, etc.
6. USB Type-C to connect to a mobile phone or computer for recording and firmware upgrade
7. USB Type-C for device power supply and charging

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note:
This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This device has been evaluated to meet general RF exposure. The device can be used in portable exposure conditions with restrictions.

• Product Name: Multi-Effects Processor
• Model Number: QME-10
• Changsha Sonicake Technology Co., Ltd
• FCC ID: 2A7J4-QME10
• IC: 30072-QME10
• HVIN: QME-10

IC Caution:
Radio Standards Specification RSS-Gen, issue 5 This device contains license-exempt transmitter (s)/ receiver (s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS (s).

Operation is subject to the following two conditions:

• This device may not cause interference.
• This device must accept any interference, including interference that may cause undesired operation of the device.

RF exposure statement:
This device has been evaluated to meet general RF exposure. The device can be used in portable exposure conditions with restriction

• IC: 30072-QME10

Made in China.

www.sonicake.com.