Sunricher 2108HT RDM High Volt LED Strip Controller
Important: Read All Instructions Prior to Installation
Function introduction
Product Data
Input Voltage | Output Voltage | Output Current | Max Load | Size(LxWxH) | Ambient Temp. |
AC 100-240V | DC 100-240V | Max. 4×1.5A | 660W@110V
1320W@220V |
180.5×73.6x38mm | -20℃-+50℃ |
- RDM enabled DMX high voltage LED strip controller
- Output for high voltage DC100~240V LED Strip
- Standard DMX512 compliant control interface
- RDM function enabled to realization of intercommunication between DMX master and decoder.
- For example, the DMX decoder’s address can be assigned by the DMX master console
- With a digital display to show data directly, easily to set and show the DMX address.
- Total 4 channels LED output, common anode
- DMX address manually settable
- DMX channel quantity from 1CH~4CH settable
- Output PWM frequency from 500HZ ~ 35K HZ is settable, but do not set it higher than 3KHz.
- Output dimming curve gamma value from 0.1 ~ 9.9 settable
- Waterproof grade:IP67
Safety & Warnings
- DO NOT install with power applied to the device.
- This device is IP67 rating and is protected against damp environments.
Operation
To set the desired DMX512 address through buttons
- button A is to set the “hundreds” position,
- button B is to set the “tens” position,
- button C is to set the “unit” position.
Set DMX address (Factory default DMX address is 001)
Press and hold down any of the 3 buttons for over 3 seconds, digital display flashes to enter into the address setting, then keep pressing button A to set the “hundreds” position, button B to set “tens” position, button C to set “units” position, then press and hold down any button for >3 seconds to confirm the setting.
DMX signal indicator : When DMX signal input is detected, the indicator on the display following after the digit of the “hundreds” position of the DMX address turns on red
.
Choose DMX Channel (Factory default DMX channel is 4CH)
Press and hold down both buttons B+C simultaneously for over 3 seconds, CH digital display flashes, then keep short pressing button A to choose 1/2/3/4, which means a total of 1/2/3/4 channels. Press and hold down button A for >3 seconds to confirm the setting. Factory default is 4 DMX channels. For example the DMX address is already set as 001.
- 1CH=1 DMX address for all the output channels, which all will be address 001.
- 2CH=2 DMX addresses , output 1&3 will be address 001, output 2&4 will be address 002
- 3CH=3 DMX addresses, output 1, 2 will be address 001, 002 respectively, output 3&4 will be address 003 4CH=4 DMX addresses, output 1, 2, 3, 4 will be address 001, 002, 003, 004 respectively
Choose PWM frequency (Factory default PWM frequency is PF1 1KHz)
Press and hold down both buttons A+B simultaneously for over 3 seconds, digital display will show PF1, PF means output PWM frequency, the digit 1 will flash, which means frequency, then keep short pressing button C to select a frequency from 0-9 and A-J, which stand for following frequencies: 0=500Hz, 1=1KHz, 2=2KHz, …, 9=9KHz, A=10KHz, B=12KHz, C=14KHz, D=16KHz, E=18KHz, F=20KHz, H=25KHz, J=35KHz. Then press and hold down button C for >3 seconds to confirm the setting.
Note: DO NOT set the PWM frequency higher than 3KHz to avoid overheating and damage to the device.
Choose Dimming Curve Gamma Value (Factory default dimming curve value is g1.0)
Press and hold down all buttons A+B+C simultaneously for over 3 seconds, digital display flashes g1.0, 1.0 means the dimming curve gamma value, the value is selectable from 0.1-9.9, then keep short pressing button B and button C to select corresponding digits, then press and hold down both buttons B+C for >3 seconds to confirm the setting.
Restore to Factory Default Setting
Press and hold down both buttons A+C for over 3 seconds until the digital display turns off and then turns on again, all settings will be restored to factory default.
Default settings are as follows:
- DMX Address: 001
- DMX Address Quantity: 4CH
- PWM Frequency: PF1
- Gamma: g1.0
The supported RDM PIDs are as follows:
- DISC_UNIQUE_BRANCH
- DISC_MUTE
- DISC_UN_MUTE
- DEVICE_INFO
- DMX_START_ADDRESS
- IDENTIFY_DEVICE
- SOFTWARE_VERSION_LABEL
- DMX_PERSONALITY
- DMX_PERSONALITY_DESCRIPTION
- SLOT_INFO
- SLOT_DESCRIPTION
- MANUFACTURER_LABEL
- SUPPORTED_PARAMETERS
Wiring diagram
Product Dimension
Documents / Resources
![]() |
Sunricher 2108HT RDM High Volt LED Strip Controller [pdf] Instruction Manual 2108HT WP, 09.218HP.04263, 2108HT RDM High Volt LED Strip Controller, 2108HT, RDM High Volt LED Strip Controller, Volt LED Strip Controller, LED Strip Controller, Strip Controller, Controller |