Instruction Manual for Sunricher models including: 2108HT WP, 09.218HP.04263, 2108HT RDM High Volt LED Strip Controller, 2108HT, RDM High Volt LED Strip Controller, Volt LED Strip Controller, LED Strip Controller, Strip Controller, Controller
30 ott 2024 — RDM enabled DMX high voltage LED strip controller. • Output for high voltage DC100~240V LED Strip. • Standard DMX512 compliant control interface.
20 hours ago — Important: Read All Instructions Prior to Installation. • RDM enabled DMX high voltage LED strip controller. • Output for high voltage DC100~240V LED Strip.
SR-2108HT(WP)-EU DMX512 RDM Decoder Hochspannungs-LED-Controller
DMX/RDM High Volt LED Strip Controller 09.218HP.04263 Important: Read All Instructions Prior to Installation Function introduction D+ DGND DMX512 signal input DMX INPUT DMX OUTPUT AC DMX512&RDM Controller DMX INPUT/ OUTPUT Grey White:D+ Blue:DBlack:GND ta:-20-+50 PRI: Uin=100-240VAC Iin=6A Max SEC: Uout=4x(100-240)VDC Iout=4x1.5A Pout=4x(150-360)W DC 100-240V LED OUTPUT Brown :V+ Black :RYellow+Green :GBlue :BGrey White: W- IP67 AC INPUT DC OUTPUT Common Anode Output(+) CH 1:R output(-) CH 2:G output(-) CH 3:B output(-) CH 4:W output(-) AC100-240V power input D+ DGND DMX512 signal input Product Data Input Voltage Output Voltage AC 100-240V DC 100-240V Output Current Max. 4x1.5A Max Load Size(LxWxH) 660W@110V 1320W@220V 180.5x73.6x38mm Ambient Temp. -20-+50 · RDM enabled DMX high voltage LED strip controller · Output for high voltage DC100~240V LED Strip · Standard DMX512 compliant control interface · RDM function enabled to realize intercommunication between DMX master and decoder. · For example, DMX decoder's address can be assigned by DMX master console · With digital display to show data directly, easily to set and show DMX address. · Total 4 channels LED output, common anode · DMX address manually settable · DMX channel quantity from 1CH~4CH settable · Output PWM frequency from 500HZ ~ 35K HZ settable, but do not set it higher than 3KHz. · Output dimming curve gamma value from 0.1 ~ 9.9 settable · Waterproof grade:IP67 Safety & Warnings · DO NOT install with power applied to device. · This device is IP67 rating and protected against damp environment. Operation To set desired DMX512 address through buttons, button A is to set "hundreds" position, button B is to set "tens" position, button C is to set "unit" position. ABC Set DMX address (Factory default DMX address is 001) Press and hold down any of the 3 buttons for over 3 seconds, digital display flashes to enter into address setting, then keep short pressing button A to set "hundreds" position, button B to set "tens" position, button C to set "units" position, then press and hold down any button for >3 seconds to confirm the setting. DMX signal indicator : When DMX signal input is detected, the indicator on the display following after the digit of "hundreds" position of DMX address turns on red . Choose DMX Channel (Factory default DMX channel is 4CH) Press and hold down both buttons B+C simultaneously for over 3 seconds, CH digital display flashes, then keep short pressing button A to choose 1/2/3/4, which means total 1/2/3/4 channels. Press and hold down button A for >3 seconds to confirm the setting. Factory default is 4 DMX channels. For example the DMX address is already set as 001. 1CH=1 DMX address for all the output channels, which all will be address 001. 2CH=2 DMX addresses , output 1&3 will be address 001, output 2&4 will be address 002 3CH=3 DMX addresses, output 1, 2 will be address 001, 002 respectively, output 3&4 will be address 003 4CH=4 DMX addresses, output 1, 2, 3, 4 will be address 001, 002, 003, 004 respectively Choose PWM frequency (Factory default PWM frequency is PF1 1KHz) Press and hold down both buttons A+B simultaneously for over 3 seconds, digital display will show PF1, PF means output PWM frequency, the digit 1 will flash, which means frequency, then keep short pressing button C to select a frequency from 0-9 and A-J, which stand for following frequencies: 0=500Hz, 1=1KHz, 2=2KHz, ..., 9=9KHz, A=10KHz, B=12KHz, C=14KHz, D=16KHz, E=18KHz, F=20KHz, H=25KHz, J=35KHz. Then press and hold down button C for >3 seconds to confirm the setting. Note: DO NOT set the PWM frequency higher than 3KHz to avoid over heat and damage to the device. Choose Dimming Curve Gamma Value (Factory default dimming curve value is g1.0) Press and hold down all buttons A+B+C simultaneously for over 3 seconds, digital display flashes g1.0, 1.0 means the dimming curve gamma value, the value is selectable from 0.1-9.9, then keep short pressing button B and button C to select corresponding digits, then press and hold down both buttons B+C for >3 seconds to confirm the setting. output brightness level 1.0 0.8 3.5 0.9 2.5 1.5 6.5 gamma value <1 >1 DMX value level Restore to Factory Default Setting Press and hold down both buttons A+C for over 3 seconds until the digital display turns off and then turns on again, all settings will be restored to factory default. Default settings are as follows: DMX Address: 001 DMX Address Quantity: 4CH PWM Frequency: PF1 Gamma: g1.0 The supported RDM PIDs are as follows: DISC_UNIQUE_BRANCH DISC_MUTE DISC_UN_MUTE DEVICE_INFO DMX_START_ADDRESS IDENTIFY_DEVICE SOFTWARE_VERSION_LABEL DMX_PERSONALITY DMX_PERSONALITY_DESCRIPTION SLOT_INFO SLOT_DESCRIPTION MANUFACTURER_LABEL SUPPORTED_PARAMETERS Wiring diagram DMX D+ D- Master GND DMX OUTPUT DMX INPUT AC DMX512&RDM Controller DMX INPUT/ OUTPUT Grey White:D+ Blue:DBlack:GND ta:-20-+50 PRI: Uin=100-240VAC Iin=6A Max SEC: Uout=4x(100-240)VDC Iout=4x1.5A Pout=4x(150-360)W DC 100-240V LED OUTPUT Brown :V+ Black :RYellow+Green :GBlue :BGrey White: W- IP67 AC INPUT DC OUTPUT V+ V+ R- R- G- G- B- B- W- W- High Volt RGBW LED Strip AC Power 100-240VAC DMX INPUT AC DMX512&RDM Controller DMX INPUT/ OUTPUT Grey White:D+ Blue:DBlack:GND ta:-20-+50 PRI: Uin=100-240VAC Iin=6A Max SEC: Uout=4x(100-240)VDC Iout=4x1.5A Pout=4x(150-360)W DC 100-240V LED OUTPUT Brown :V+ Black :RYellow+Green :GBlue :BGrey White: W- IP67 AC INPUT DC OUTPUT DMX OUTPUT DMX INPUT AC DMX512&RDM Controller DMX INPUT/ OUTPUT Grey White:D+ Blue:DBlack:GND ta:-20-+50 PRI: Uin=100-240VAC Iin=6A Max SEC: Uout=4x(100-240)VDC Iout=4x1.5A Pout=4x(150-360)W DC 100-240V LED OUTPUT Brown :V+ Black :RYellow+Green :GBlue :BGrey White: W- IP67 AC INPUT DC OUTPUT DMX OUTPUT Product Dimension V+ V+ WW WW CW CW WW WW CW CW V+ V+ 1- V- 2- V- 3- V- 4- V- High Volt Tunable White LED Strip AC Power 100-240VAC High Volt Single Color LED Strip High Volt Single Color LED Strip AC Power 100-240VAC 73.6 170.0 180.5 38.0Corel PDF Engine Version 14.0.0.653