roborock 11th Anniversary Programming Mode User Guide

11th Anniversary Programming Mode

“

Product Specifications

• Recommended Programs: Three pre-installed programs
• Programming Mode Features: Build custom programs, execute
  recommended programs, copy programs
• Modules: Move, Robotic Arm, Task
• Execution Control: Start, pause, stop programs
• Save and Manage Programs: Rename, copy, delete programs

Product Usage Instructions

1. Entering Programming Mode

To enter Programming Mode:

1. Access the map page on the robot.
2. Ensure the following start conditions are met:
   • The robot is functioning properly.
   • Battery level is above 20%.
   • The robot is not performing any tasks.
   • The Robotic Arm is enabled. If disabled, enable it in Settings
     > Robotic Arm Setting.
3. A prompt will pop up when start conditions are met.

2. Basic Operations

2.1 Recommended Programs

Three recommended programs are available:

• To execute a recommended program directly: Tap the program and
  then tap Start.
• To create your own program based on a recommended one: Tap the
  program, edit, and save it to My Program.
• To copy a recommended program: Tap + on the program to add it
  to My Program.

2.2 Create My Program

To create a custom program:

1. Tap Build a Program to enter the creation interface.
2. Drag the blocks into the block coding area to build a program.
   • Move: Add blocks for robot movement (forward,
     backward, rotate).
   • Robotic Arm: Control the robotic arm’s
     actions.
   • Task: Add delays and voice lines to the
     program.
3. Rearrange blocks by dragging them and delete by dragging into
   the tab on the left.
4. Tap the program name to edit it.
5. During execution, tap Stop to pause the program. The system
   will display status updates.
6. Tap Complete to save the program under My Program on the
   homepage.

Safety Note:

Ensure a safe environment before using the programming function
to avoid potential hazards.

Frequently Asked Questions (FAQ)

Q: How can I troubleshoot if my robot stops during program
execution?

A: Check the battery level, ensure the robotic arm is enabled,
and review the program for errors. Restart if needed.

“`

User Guide for Programming Mode

1. Entering Programming Mode
You can enter the Programming Mode from the map page.
When entering, the robot will check whether the start conditions are met. If not, a prompt will pop up. Start Conditions: The robot can function properly.

The robot’s battery level is above 20%. The robot is not performing any tasks. Robotic arm is enabled. *If disabled, enable it in Settings > Robotic Arm Setting.
A prompt will pop up when the start conditions are met.

2. Basic Operations
2.1 Recommended Programs Three recommended programs are pre-installed in the system. They can be executed directly or copied to “My Program”.

Execute a recommended program directly: Tap a recommended program to enter the editing page, and then tap “Start” to run it.
Create your own program based on a recommended one: Tap a recommended program to enter the editing page. After editing and saving, it will be added to “My Program”.
Copy a recommended program: Tap “+” on a recommended program to add it to “My Program”.
2.2 Create My Program
Tap “Build a Program” to enter the creation interface. Then, drag the blocks into the block coding area to build a program.

1. Move
In the Move module, you can add blocks to make the robot move forward, backward, rotate, and more. Drag the blocks you need into the block coding area.

2. Robotic Arm In the Robotic Arm module, you can add blocks to control the robotic arm’s extension, retraction, movement, and more.
Notes: You need to add “Extend robotic arm” before any other actions can be executed. Diagrams for M3, M4, and M5:

3. Task In the Task module, you can add delay blocks and voice lines. The delay block can be inserted between two programming blocks to extend the time interval between actions.
4. Rearrange and Delete Drag to rearrange the order of programming blocks. To delete a block, drag it into the tab on the left.

5. Rename Tap the program name to edit it.
6. Execute Program During execution, the current status will be displayed. Tap “Stop” to pause the program while it’s running. If an error occurs during execution, the program may stop automatically or exit Programming Mode. Once completed, the system will display a “Tasks completed” status.

7. Save Program Tap “Complete” to save the program.

The saved program will appear under “My Program”on the Programming Mode homepage.
You can execute the program, as well as rename, copy, or delete it.
Note: Ensure a safe surrounding environment before activating this function. Be aware of potential hazards. The app interface is subject to change without notice.

Documents / Resources

roborock 11th Anniversary Programming Mode [pdf] User Guide 11th Anniversary Programming Mode, 11th Anniversary Programming Mode, Programming Mode, Mode

References

• User Manual