roborock 11th Anniversary Programming Mode

Product Specifications
- Recommended Programs: Three pre-installed programs
- Programming Mode Features: Build custom programs, execute recommended programs, and copy programs
- Modules: Move, Robotic Arm, Task
- Execution Control: Start, pause, stop programs
- Save and Manage Programs: Rename, copy, and delete programs
Product Usage Instructions
Entering Programming Mode
To enter Programming Mode:
- Access the map page on the robot.
- Ensure the following start conditions are met:
- The robot is functioning properly.
- Battery level is above 20%.
- The robot is not performing any tasks.
- The Robotic Arm is enabled. If disabled, enable it in Settings > Robotic Arm Setting.
- A prompt will pop up when start conditions are met.
Basic Operations
Recommended Programs
Three recommended programs are available:
- To execute a recommended program directly: Tap the program and then tap Start.
- To create your own program based on a recommended one: Tap the program, edit, and save it to My Program.
- To copy a recommended program: Tap + on the program to add it to My Program.
Create My Program
To create a custom program:
- Tap Build a Program to enter the creation interface.
- Drag the blocks into the block coding area to build a program.
- Move: Add blocks for robot movement (forward, backward, rotate).
- Robotic Arm: Control the robotic arm’s actions.
- Task: Add delays and voice lines to the program.
- Rearrange blocks by dragging them and delete by dragging into the tab on the left.
- Tap the program name to edit it.
- During execution, tap Stop to pause the program. The system will display status updates.
- Tap Complete to save the program under My Program on the homepage.
Safety Note:
Ensure a safe environment before using the programming function to avoid potential hazards.
User Guide for Programming Mode

Entering Programming Mode
- You can enter the Programming Mode from the map page.

- When entering, the robot will check whether the start conditions are met. If not, a prompt will pop up.
Start Conditions:
- The robot can function properly.
- The robot’s battery level is above 20%.
- The robot is not performing any tasks.
- Robotic arm is enabled.
- If disabled, enable it in Settings > Robotic Arm Setting.
A prompt will pop up when the start conditions are met.

Basic Operations
Recommended Programs
Three recommended programs are pre-installed in the system. They can be executed directly or copied to “My Program”.
- Execute a recommended program directly: Tap a recommended program to enter the editing page, and then tap “Start” to run it.
- Create your own program based on a recommended one: Tap a recommended program to enter the editing page. After editing and saving, it will be added to “My Program”.
- Copy a recommended program: Tap “+” on a recommended program to add it to “My Program”.
Create My Program

- Tap “Build a Program” to enter the creation interface.
- Then, drag the blocks into the block coding area to build a program.

Move
- In the Move module, you can add blocks to make the robot move forward, backward, rotate, and more. Drag the blocks you need into the block coding area.

Robotic Arm
- In the Robotic Arm module, you can add blocks to control the robotic arm’s extension, retraction, movement, and more.

Notes:
- You need to add “Extend robotic arm” before any other actions can be executed.
- Diagrams for M3, M4, and M5:

Task
- In the Task module, you can add delay blocks and voice lines. The delay block can be inserted between two programming blocks to extend the time interval between actions.

Rearrange and Delete
- Drag to rearrange the order of programming blocks.
- To delete a block, drag it into the tab on the left.

Rename
- Tap the program name to edit it.

Execute Program
- During execution, the current status will be displayed.
- Tap “Stop” to pause the program while it’s running.
- If an error occurs during execution, the program may stop automatically or exit Programming Mode.
- Once completed, the system will display a “Tasks completed” status.

Save Program
- Tap “Complete” to save the program.

- The saved program will appear under ”My Program”on the Programming Mode homepage.
You can execute the program, as well as rename, copy, or delete it.

Note:
- Ensure a safe surrounding environment before activating this function. Be aware of potential hazards.
- The app interface is subject to change without notice.
FAQs
Q: How can I troubleshoot if my robot stops during program execution?
Documents / Resources
![]() | 11th Anniversary Programming Mode |
References
- User Manualmanual.tools

