MEAN WELL NPF-40D Series 40W Single Output LED Driver User Manual
Features
- Plastic housing with class II design
- Built-in active PFC function
- Class 2 power unit
- Standby power consumption <0.5W
- IP67 rating for indoor or outdoor installations
- Function: 3 in 1 dimming (dim-to-off)
- Typical lifetime >50000hours
- 5 years warranty
- LED panel lighting
- LED downlight
- LED decorative lighting
- LED tunnel lighting
- Moving sign
- Type “HL” for use in Class I, Division 2 hazardous (Classified) location
Description
NPF-40D series is a 40W AC/DC LED driver featuring the constant current mode output. NPF-40D operates from 90-‘305VAC and offers models with different rated voltage ranging between 12V and 54V. Thanks to the high efficiency up to 90%, with the fanless design, the entire series is able to operate for -40°C-‘+85°C case temperature under free air convection. The entire series is rated with IP67 ingress protection level and is suitable to work for a variety of applications at dry, damp or wet locations. NPF-40D is equipped with the 3 in 1 dimming function so as to provide the design flexibility for LED lighting system.
Model Encoding
SPECIFICATION
MODEL |
NPF-40D-12 | NPF-40D-15 | NPF-40D-20 | NPF-40D-24 | NPF-40D-30 | NPF-40D-36 | NPF-40D-42 | NPF-40D-48 | NPF-40D-54 | |
OUTPUT |
RATED CURRENT | 3.34A | 2.67A | 2A | 1.67A | 1.34A | 1.12A | 0.96A | 0.84A | 0.76A |
RATED POWER | 40.08W | 40.08W | 40W | 40.08W | 40.2W | 40.32W | 40.32W | 40.32W | 41.04W | |
CONSTANT CURRENT REGION | 7.2 ~ 12V | 9 ~ 15V | 12 ~ 20V | 14.4 ~ 24V | 18 ~ 30V | 21.6 ~ 36V | 25.2 ~ 42V | 28.8 ~ 48V | 32.4 ~ 54V | |
CURRENT RIPPLE | 5.0% max. @rated current | |||||||||
CURRENT TOLERANCE | ±5.0% | |||||||||
SET UPTIME Note.3 | 500ms/115VAC, 230VAC | |||||||||
INPUT |
VOLTAGE RANGE Note.2 | 90 ~ 305VAC 127 ~ 431VDC
(Please refer to “STATIC CHARACTERISTIC” section) |
||||||||
FREQUENCY RANGE | 47 ~ 63Hz | |||||||||
POWER FACTOR (Typ.) | PF 0.97/115VAC, PF 0.95/230VAC, PF 0.92/277VAC@full load
(Please refer to “POWER FACTOR (PF) CHARACTERISTIC” section) |
|||||||||
TOTAL HARMONIC DISTORTION | TH D< 20%(@load 60%/1 1 5VC, 230VAC; @load 75%/277VAC) (Please refer to “TOTAL HARMONIC DISTORTION(THD)” section) | |||||||||
EFFICIENCY(Typ.) | 86% | 87% | 88% | 89% | 89% | 90% | 90% | 90% | 90% | |
AC CURRENT (Typ.) | 0.6A / 115VAC 0.3A / 230VAC 0.25A / 277VAC | |||||||||
INRUSH CURRENT(Typ.) | COLD START 50A(twidth=270 μ s measured at 50% Ipeak) at 230VAC; Per NEMA 410 | |||||||||
MAX. NO. of PSUs on 16A CIRCUIT BREAKER | 9 units (circuit breaker of type B) / 16 units (circuit breaker of type C) at 230VAC | |||||||||
LEAKAGE CURRENT | <0.25mA / 277VAC | |||||||||
STANDBY POWER CONSUMPTION | <0.5W | |||||||||
PROTECTION |
OVER CURRENT | 95 ~ 108% | ||||||||
Constant current limiting, recovers automatically after fault condition is removed | ||||||||||
SHORT CIRCUIT | Hiccup mode, recovers automatically after fault condition is removed | |||||||||
OVER VOLTAGE | 15 ~ 17V | 17.5 ~ 21V | 23 ~ 27V | 28 ~ 34V | 34 ~ 40V | 41 ~ 46V | 46 ~ 54V | 54 ~ 60V | 59 ~ 66V | |
Shut down o/p voltage, re-power on to recover | ||||||||||
OVER TEMPERATURE | Shut down o/p voltage, re-power on to recover | |||||||||
ENVIRONMENT |
WORKING TEMP. | Tcase=-40 ~ +85 ℃ (Please refer to “ OUTPUT LOAD vs TEMPERATURE” section) | ||||||||
MAX. CASE TEMP. | Tcase=+85℃ | |||||||||
WORKING HUMIDITY | 20 ~ 95% RH non-condensing | |||||||||
STORAGE TEMP., HUMIDITY | -40 ~ +80℃, 10 ~ 95% RH | |||||||||
TEMP. COEFFICIENT | ± 0.03%/℃ (0 ~ 50℃) | |||||||||
VIBRATION | 10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes | |||||||||
SAFETY & EMC |
SAFETYSTANDARDS | UL8750(type”HL”), UL879(for 12V,24V only), CSA C22.2 No. 250.13-12, ENEC BS EN/EN61347-1, BS EN/EN61347-2-13, BS EN/EN62384 independent, EACTPTC 004, GB19510.1,GB19510.14, IP67 approved ; Design refer to BS EN/EN60335-1 | ||||||||
WITHSTAND VOLTAGE | I/P-O/P:3.75KVAC | |||||||||
ISOLATION RESISTANCE | I/P-O/P:100M Ohms / 500VDC / 25℃/ 70% RH | |||||||||
EMC EMISSION | Compliance to BS EN/EN55015, BS EN/EN61000-3-2 Class C ( @ load 60%) ; BS EN/EN61000-3-3;
GB17743 and GB17625.1,EACTPTC 020 |
|||||||||
EMC IMMUNITY | Compliance to BS EN/EN61000-4-2,3,4,5,6,8,11; BS EN/EN61547, light industry level(surge immunity Line-Line 2KV);EACTPTC 020 | |||||||||
OTHERS |
MTBF | 1016.8K hrs min. Telcordia SR-332 (Bellcore) ; 314.44K hrs min. MIL-HDBK-217F (25℃) | ||||||||
DIMENSION | 150*53*35mm (L*W*H) | |||||||||
PACKING | 0.49Kg;30pcs/15.7Kg/1.0CUFT | |||||||||
NOTE |
※ Product Liability Disclaimer : For detailed information , please refer to https://www.meanwell.com/serviceDisclaimer.aspx |
BLOCK DIAGRAM
- PFC fosc : 50~120KHz
- PWM fosc : 60~130KHz
DRIVING METHODS OF LED MODULE
- ※ This series works in constant current mode to directly drive the LEDs.
Typical LED power supply I-V curve
DIMMING OPERATION
※ 3 in 1 dimming function
- Output constant current level can be adjusted by applying one of the three methodologies between DIM+ and DIM-: 0 ~ 10VDC, or 10V PWM signal or resistance.
- Direct connecting to LEDs is suggested. It is not suitable to be used with additional drivers.
- Dimming source current from power supply: 100 A (typ.) μ
- Applying additive 0 ~ 10VDC
“DO NOT connect “DIM- to Vo-”
Dimming input: Additive voltage
- Applying additive 10V PWM signal (frequency range 100Hz ~ 3KHz):
DO NOT connect “DIM- to Vo-”
Duty cycle of additive 10V PWM signal dimming input - ◎ Applying additive resistance:
“DO NOT connect “DIM- to Vo-”
(N=driver quantity for synchronized ) dimming operation Dimming input: Additive resistance
Note :
- Min. dimming level is about 6% and the output current is not defined when 0%< out<6%. I
- The output current could drop down to 0% when dimming input is about 0k or 0Vdc, or 10V PWM signal with 0% duty cycle.
OUTPUT LOAD vs TEMPERATURE
STATIC CHARACTERISTIC
※De-rating is needed under low input voltage.
POWER FACTOR (PF) CHARACTERISTIC
※ Tcase at 75℃
TOTAL HARMONIC DISTORTION (THD)
※ 48V Model, Tcase at 75℃
EFFICIENCY vs LOAD
NPF-40D series possess superior working efficiency that up to 90% can
be reached in field applications.
※ 48V Model, Tcase at 75℃
LIFE TIME
MECHANICAL SPECIFICATION
Recommend Mounting Direction
INSTALLATION MANUAL
Please refer to http://www.meanwell.com/manual.html
Documents / Resources
![]() |
MEAN WELL NPF-40D Series 40W Single Output LED Driver [pdf] User Manual NPF-40D Series, 40W Single Output LED Driver, NPF-40D Series 40W Single Output LED Driver, Single Output LED Driver, Output LED Driver, LED Driver |