KRAMER KDS-EN7 Hagaha Isticmaalaha Waxqabad Sare/Miisaan Leh 4K AVoIP

KRAMER- KDS-EN7 -High -Performance Scalable- 4K- AVoIP -Encoder

KDS-EN7, KDS-DEC7 Quick Start Guide

This guide helps you install and use your KDS-EN7, and KDS-DEC7 for the first time. Go to www.kramerav.com/downloads/KDS-EN7 si aad u soo dejiso buugga isticmaalaha ee ugu dambeeyay oo aad u hubiso haddii qalabka wax lagu casriyeeyo la heli karo.

Tallaabada 1: Calaamadee waxa sanduuqa ku jira 

• KDS-EN7 4K AVoIP Encoder or KDS-DEC7 4K AVoIP Decoder`
• 2 Bracket sets for each product
• 1 Hagaha bilawga degdega ah

Step 2: Get to know your KDS-EN7 and KDS-DEC7

#	feature		function
1	HOST USB Type B Port		Connect to a USB host, for example, a PC for KVM/USB support.
2	Muujinta LCD		Use for device configuration such as unique channel/AV stream setting on encoder and channel tuning on decoder.
3	Menu Navigation Button	ƒ	Riix si aad ugu noqoto liiska hore.
			Press to move up to the next configuration parameter.
		„	Press to go to the next menu.
		‚	Press to move down to the next configuration parameter.
		Ku qor	Press to accept changes.
4	LINK LINK		Eeg LED Functionality.
5	NET LED		Eeg LED Functionality.
6	Laydhka		Eeg LED Functionality.
7	24V/1A DC Connector		Connect to the power adapter (purchased separately).
8	Dib u cusboonaysii badhanka dib loo furay		Press and hold for 10 seconds to reset the device to its factory default values. All LEDs flash.
9	LAN MEDIA 1G(PoE) RJ-45 Port		Unicast: connect for streaming either directly to a decoder or via LAN. Multicast: connect to multiple decoders or connect to one decoder to which multiple decoders are daisy-chained via SERVICE (1G) port.
10	LAN SERVICE 1G RJ-45 Port		Used OPTIONALLY for physical separation between AV and command streams to separate LAN for security and reliability purposes.
11	RS-232 3-pin Terminal Block Connector		Connect to an RS-232 device to use as a Gateway and bi-directional signal extension (even when no AV signal is extended).
12	AUDIO IN/OUT 5-pin Iskuxirka Terminal Block		Connect to a balanced analog stereo audio source/acceptor.
13	IR 3.5 Mini Jack		Connect to an IR sensor or emitter for bi-directional signal extension (even when no AV signal is extended). Expected voltage for IR receiver – (3.3V).
14	HDMI IN Connector		Ku xidh isha HDMI.
15	Xidhiidhiyaha HDMI OUT		Connect to loop the signal.

#	feature		function
16	USB Nooca A Port		Connect to a keyboard and mouse.
17	Muujinta LCD		Upon power up, displays the last video source. Use for device information and configuration.
18	Menu Navigation Button	ƒ	Riix si aad ugu noqoto liiska hore.
			Press to move up to the next configuration parameter.
		„	Press to go to the next menu.
		‚	Press to move down to the next configuration parameter.
		Ku qor	Press to accept changes.
19	LINK LINK		Eeg LED Functionality.
20	NET LED		Eeg LED Functionality.
21	Laydhka		Eeg LED Functionality.
22	24V/1A DC Connector		Connect to the power adapter (purchased separately).
23	Dib u cusboonaysii badhanka dib loo furay		Press and hold for 10 seconds to reset the device to its factory default values. All LEDs flash.
24	LAN MEDIA 1G(PoE) Dekedda RJ-45		Connect for streaming.
25	LAN SERVICE 1G Dekedda RJ-45		Use, optionally, to create a physical separation between AV streams (MEDIA) and command streams (SERVICE), for enhancing security and reliability.
26	RS-232 3-pin Terminal Block Connector		Connect to an RS-232 device to use as a Gateway and bi-directional signal extension (even when no AV signal is extended).
27	AUDIO OUT 5-pin Iskuxirka Terminal Block		Connect to a balanced analog stereo audio acceptor.
28	IR 3.5 Mini Jack		Connect to an IR sensor or emitter for bi-directional signal extension (even when no AV signal is extended). Expected voltage for IR receiver – (3.3V).
29	HDMI IN Connector		Connect to an HDMI source. Can be used, alternatively, as a backup input to the decoder.
30	Xidhiidhiyaha HDMI OUT		Connect an acceptor.

Waxqabadka LED 

KDS-EN7 and KDS-DEC7 LEDs function as follows:

LED	Color	Qeexid
LINK LINK	Lights Green	A link is established between KDS-EN7 iyo KDS-DEC7 and is transmitting A/V signals.
	Nalalka Cagaaran	A signal is established, and a problem is detected.
NET LED	Off	No IP address is acquired.
	Nalalka cagaaran	A valid IP address has been acquired.
	Flashes Green very fast (for 60sec)	A device identification command is sent (Flag me).
	Lights Yellow	Device falls back to default IP address.
	Lights Red	Security is blocking IP access.
Laydhka	Nalal cas	On fallback address acquiring, device ‘ON’ LED flashes continuously in slow 0.5/10sec cadence.
	Lights Green	When power is on.
	Flashes Green Slowly	Device is in standby mode.
	Dhakhso cagaar ah u iftiimaya	FW is downloaded in the background.
	Flashes Green very fast (for 60sec)	A device identification command is sent (Flag me).
	Lights Yellow	Device falls back to default IP address.
	Lights Red	Security is blocking IP access.
Post reboot, all LEDs light for 3 seconds then return to their normal LED display mode.

Install KDS-EN7 using one of the following methods:

• Ku dheji cagaha caagga ah oo dhig cutubka dusha sare.
• Ku dheji qaybta (ku dar) dhinac kasta oo ka mid ah cutubka kuna dheji dusha sare (eeg www.kramerav.com/downloads/KDS-EN7).
• Ku dhaji cutubka santuuqa adoo adeegsanaya adabtarada rakiba ee lagu taliyay (eeg www.kramerav.com/product/KDS-EN7).
• Hubi in deegaanka (tusaale, heerkulka deegaanka ugu sarreeya & socodka hawada) uu la jaanqaadi karo qalabka.
• Ka fogow rarka farsamada ee aan sinnayn.
• Tixgelinta habboon ee qiimeynta taarikada qalabka waa in loo adeegsadaa si looga fogaado culeyska xad-dhaafka ah ee wareegyada.
• Dhuxul la isku hallayn karo oo ka mid ah qalabka rakiba-lagu rakibo waa in la ilaaliyaa.
• Dhererka ugu sarreeya ee qalabka waa 2 mitir.

Tallaabada 4: Ku xir gashiga iyo wax soo saarka 

Always switch OFF the power on each device before connecting it to your KDS-EN7 and KDS-DEC7.

KDS-EN7 and KDS-DEC7 can stream 4K video, requiring a gigabit Ethernet switch for high-quality performance, since the maximum momentary transfer rate can reach 850Mbps. We recommend using AVoIP Ethernet switches that support: Multicast forwarding or filtering, IGMP Snooping, IGMP Querier, IGMP snooping fast leave, and Jumbo frame (8000 bytes or larger).

Connecting the audio input/output

Si aad u gaarto masaafada la cayimay, isticmaal fiilooyinka Kramer ee lagu taliyay ee laga heli karo www.kramerav.com/product/KDS-EN7. Using third-party cables may cause damage!

Tallaabada 5: Ku xir awoodda 

By default, the device uses PoE for powering the device. Optionally, you can separately purchase a power adapter to connect to the product and plug into the mains electricity. Safety Instructions (See www.kramerav.com si aad u hesho macluumaad badbaado oo la cusboonaysiiyay

digniin:

• Alaabooyinka leh marinada gudbinta iyo dekedaha GPIO, fadlan tixraac qiimaynta la ogolyahay ee xidhiidhka dibadeed, ee ku ag yaal terminalka ama Buuga isticmaale.
• Ma jiraan qaybo ka shaqeeya adeegga oo ku dhex jira cutubka.

Digniin: 

• Adeegso oo keliya xarigga korantada ee qeybta la siiyay.
• Ka jooji korontada oo ka fur qeybta gidaarka ka hor intaadan rakibin.

Step 6: Operate KDS-EN7 

Allocating the IP Address via LCD screen menu
KDS-EN7 / KDS-DEC7 IP default addresses are: 192.168.1.39 for the Encoder and 192.168.1.40 for the Decoder. By default, DHCP is enabled, and assigns an IP address to the device. If DHCP Server is not available, for example, in case a device is connected directly to the laptop, that device gets the default IP address. If these IP addresses are already in use, the system searches for a random unique IP in the range of 192.168.X.Y. the allocated IP address can be identified using the LCD screen menu.
To allocate the IP address via LCD screen Menu:

1. Connect the device to the 24V DC power adapter and connect the adapter to the mains electricity. The ON LED lights green, and the LINK LED flashes (indicating that no streaming activity is detected).
2. Use the Navigation button to view the assigned IP address on the LCD screen:
   1. • DEV STATUS > LAN1 Status
      • DEV STATUS > LAN2 Status (if the Service port is connected as well).

Setting Channel Number
Each encoder requires a unique channel number, and the connected decoders should be tuned to that encoder channel. You can set the channel number via the LCD screen menu or the embedded web boggaga.
To set the channel number for KDS-EN7/KDS-DEC7, via LCD screen menu:

1. Connect the device to the 24V DC power adapter and connect the adapter to the mains electricity. The ON LED lights green, and the LINK LED flashes (indicating that no streaming activity is detected).
2. Change channel number using arrow buttons:
   1. • For the KDS-EN7, In the LCD screen menu, go to DEV SETTINGS > CH DEFINE, set a unique channel number and press Enter to save your selection.
      • For each of the KDS-DEC7 devices, set to the defined KDS-EN7 channel number.

To set the channel number via web bogagga: 

1. Connect the KDS-EN7 / KDS-DEC7 Ethernet port to the network and power the device.
2. Gelida ku-xidhan web boggaga.
3. In the Main page:\
   For KDS-EN7:
   1. • Go to AV Routing page.
      • Select Channel ID and define the channel ID number.

For KDS-DEC7: 

• Go to AV Routing page.
• Select Channel ID (corresponding to the desired encoder channel ID).

Dukumentiyada / Kheyraadka

KRAMER KDS-EN7 High Performance/Scalable 4K AVoIP Encoder [pdf] Hagaha Isticmaalaha KDS-EN7, KDS-DEC7, KDS-EN7 High Performance Scalable 4K AVoIP Encoder, High Performance Scalable 4K AVoIP Encoder