EGATE-PRO
Quick Guide
EGATE-PRO ZigBee Universal Gateway
Product Compliance
This product complies with the following EU Directives: 2014/53/EU i 2011/65/EU.
Safety information
Use in accordance with national and EU regulations. Use the device only as intended, keeping it in a dry condition. The product is for indoor use only. Please read the entire manual, before installation or use.
Installation:
Installation must be performed by a qualified person with appropriate electrical qualifications, in accordance with the standards and regulations in force in a given country and in the EU. The manufacturer is not responsible for non-compliance with the instructions.
WARNING:
For the entire installation, there may be additional protection requirements, which the installer is responsible for.
Gateway description
- Antenna
- Blue diode
- Red diode
- SMA antenna socket
- RESET button
- USB power socket type C
- LAN Ethernet input (RJ45)
Internet gateway operating modes
The ZigBee gateway can communicate over the internet with the cloud in two ways:
– 2.4 GHz Wi-Fi network
– Ethernet network via LAN cable
Introduction
The Internet gateway meets the needs of the most demanding Engo Smart users. It is very easy to configure the network and the communication method can be chosen between Wi-Fi or LAN. An external antenna increases the range which ensures stable communication even in large flats or houses. It easily overcomes a reinforced concrete ceiling or several partition walls. The ability to migrate network settings to a new device without losing data gives the user security and convenience.
The function of changing communication channel settings from the device interface, eliminates interference from other devices and ensures stable operation. Operation in the ZigBee 3.0 standard allows the connection of compatible devices operating in the Tuya system. Works with Google Home and Alexa voice assistants. Housing suitable for mounting on a wall or as a free-standing unit.
Product features
 |
ZigBee 3.0 communication standard |
 |
Wi-Fi 2.4 GHz communication standard |
 |
Ethernet socket (RJ45) |
 |
Compatibility with the application ENGO Smart (in technology Tuya Cloud) |
 |
LEDs indicating operation status |
 |
Stores smart rules |
 |
5V DC powered via USB type C |
Technical data
| Power supply | 5V DC USB type C |
| Communication | ZigBee 3.0 2,4GHz Wi-Fi 2,4GHz Ethernet (RJ45) |
| Dimensions | 90 x 90 x 22mm |
Explanation for LED indicator
| Red diode | Blue diode | Device status |
| Lights on continously | Lights on continously | Immediately after switching on the power supply, both LEDs light up continuously for a few seconds or immediately after a factory reset of the device |
| Flashes slowly | Lights on continously | A few seconds after switching on, the gateway is ready for pairing with the application |
| Lights on continously | Does not lights | Connected to the cloud |
| Lights on continously | Flashes | ZigBee network is opened – searching for devices |
| Does not lights | Does not lights | No power supply |
Installation
ATTENTION:
A minimum distance between the router and gateway of 1m is recommended to avoid WiFi and Zigbee interference.
ATTENTION:
Connect the gateway to a 230V AC power supply, use the supplied plug and USB cable only.
Installation of the gateway in the app
Make sure your router is within range of your smartphone. Make sure you are connected to the Internet. This will reduce the pairing time of the device.
STEP1 – DOWNLAD ENGO SMART APP
Download the ENGO Smart app from Google Play or Apple App Store and install it on your smartphone.
https://engocontrols.com/redirect-app/
STEP2 – REGISTER THE NEW ACCOUNT
To register a new account, please follow the steps below:
Click „Sign Up” to create new account. 
Enter your e-mail address to which the verification code will be sent.
Enter the verification code received in the email.
Remember that you only have 60 seconds to enter the code!
Then set the login password.
STEP 3a – Installation of the Internet gateway via LAN cable
After installing the app and creating an account:
On the mobile device, make sure that the ENGO Smart app has access to the permissions (Location, Bluetooth, Nearby devices). Then turn on Bluetooth and location. Connect tothat 2.4 GHz Wi-Fi network to which you want to assign the gateway (Wi-Fi and wired Ethernet must be one network – from the same router).
Make sure the device is connected to the power supply and to the Internet via the cable (2).
Then press and hold the RESET button (1) (using the pin provided) for 10 seconds. The red LED must flash slowly, then the gateway is in pairing mode.
If the red LED flashes quickly, then press the RESET button again for 10 seconds, wait a moment and make sure that the red LED flashes slowly.
In the app, select: „Add Device”.
After finding the gateway, go „Add”
Wait for the app to configure the device.
Go „DONE”. 
The gateway has been installed and displays the main interface. On the device, the red LED lights up continuously.
STEP 3b – Installation of the Internet gateway using a 2.4 GHz Wi-Fi network
After installing the app and creating an account:
On the mobile device, make sure that the ENGO Smart app has access to the permissions (Location, Bluetooth, Nearby devices). Then turn on Bluetooth and location. Connect to that 2.4 GHz Wi-Fi network to which you want to assign the gateway (Wi-Fi and wired Ethernet must be one network – from the same router).
Make sure the unit is powered on. Then press and hold the RESET button (1) (using the pin provided) for 10 seconds. The red LED must flash slowly, then the gateway is in pairing mode.
If the red LED flashes quickly, then press the RESET button again for 10 seconds, wait a moment and make sure the red LED flashes slowly.
In the app, select: „Add Device”.
Go to the „Gateway Control” tab, then select „Smart Gateway Pro (Zigbee)”.
Click „Cable”.
Select „AP Mode”.
Check the required field and go „Next”.
Select the Wi-Fi network in which the gateway will operate and enter the password of this network.
Click „Go to Connect”. 
The device will go to the Wi-Fi network settings screen. Select the „SmartLife-XXXX” network and connect to it.
Once the network has been configured, select „Connect only this time”, then click „Back”.
Wait for the app to configure the device.
Go „DONE”.
The gateway has been installed and displays the main interface. On the device, the red LED lights up continuously.
Factory reset
To restore the default settings of the device, press the RESET button (1) and hold it for approx. 10 seconds – until both LEDs light up. Then release the button, the universal internet gateway will restore the default (factory) values and the pairing process will begin.
Ver. 1.0
Release date: VII 2024
Soft:
Main module: v1.10.0
ZigBee module: v1.0.13
https://engocontrols.com/redirect-app/
Producer:
Engo Controls sp. z o.o. sp. k.
Rolna 4 st.
43-262 Kobielice Poland
www.engocontrols.com
Documents / Resources
 |
ENGO CONTROLS EGATE-PRO ZigBee Universal Gateway [pdf] User Guide EGATE-PRO ZigBee Universal Gateway, EGATE-PRO, ZigBee Universal Gateway, Universal Gateway, Gateway |
 |
ENGO CONTROLS EGATE-PRO ZigBee Universal Gateway [pdf] User Guide EGATE-PRO ZigBee Universal Gateway, EGATE-PRO, ZigBee Universal Gateway, Universal Gateway, Gateway |