ENGO CONTROLS ECAM-L2 Wi-Fi Smart Floodlight Camera User Guide
Introduction
The outdoor camera offers Full HD 4MP resolution
and a wide 108° viewing angle. The built-in LED lamp
with adjustable brightness effectively illuminates
the monitored area. Thanks to the motion detection
function, the camera reacts to any unwanted movements.
The device has two-way audio communication with noise
reduction. The camera is equipped with a memory card slot
with a capacity of up to 256GB. The camera is suitable for a
wide temperature range, from -10°C to +50°C, making it
suitable for all conditions. In addition, thanks to the push
notification function, users can receive instant alerts via the
Ego Smart app.
Product features
4Mpx 2560*1440P
2-way audio
Motion detection
Angle of lance 108˚
Move tracking
Safety Information:
Use in accordance with national and EU regulations. Use the device only as intended. Installation must be carried out by a qualified person in accordance with national and EU regulations.
Installation
Installation must be performed by a qualified person with appropriate electrical qualifications, in accordance with the standards and regulations in force in a given country and in the EU. The manufacturer is not responsible for non-compliance with the instructions.
WARNING:
For the entire installation, there may be additional protection requirements, which the installer is responsible for (e.g., installation of an additional differential pressure overflow valve).
Camera description
Installation of the camera in the app
Make sure your router is within range of your smartphone.
Make sure you are connected to the Internet. This will reduce the pairing time of the device.
STEP1 – DOWNLAD ENGO SMART APP
Download the ENGO Smart app from Google Play or Apple App Store and install it on your smartphone.
Powered By
STEP 2 – REGISTER THE NEW ACCOUNT
To register a new account, please follow the steps below:
Click „Sign Up” to create new account.
Enter your e-mail address to which the verification code will be sent.
Enter the verification code received in the email.
Then set the login password
STEP 3A – CONNECT CAMERA TO WI-FI- Connection via Bluetooth
After installing the app and creating an account:
On your mobile device, make sure the ENGO Smart has access to permissions (Location, Bluetooth, Nearby devices). Then turn on Bluetooth and Location. Connect to 2.4GHz Wi-Fi network to which you want to assign the device.
Make sure the camera is powered on. Then press and hold the button on the back of the camera for approximately 5 seconds, until the beep. The blue LED on the front of the unit will then start flashing. The pairing mode is enabled.
In the app, select:
„Add Device”.
After finding the camera, go „Add”
Select the Wi-Fi network in which the camera will operate and enter the password of this network.
Wait for the app to configure the device with the selected Wi-Fi network.
Go „DONE”
The camera has been installed and displays the main interface.
STEP 3B – CONNECT CAMERA TO WI-FI- Connection via QR Code
After installing the app and creating an account:
On your mobile device, make sure the ENGO Smart has access to permissions (Location, Bluetooth, Nearby devices). Then turn on Bluetooth and Location. Connect to 2.4GHz Wi-Fi network to which you want to assign the device.
Make sure the camera is powered on.
Then press and hold the button on the back of the camera for approximately 5 seconds, until the beep. The blue LED on the front of the unit will then start flashing. The pairing mode is enabled.
In the app, select:
„Add Device”.
Select „Camera & Lock”
Find and click on the Wi-Fi camera in the device list.
Follow the instructions displayed on the smartphone screen.
STEP 3B – CONNECT CAMERA TO WI-FI- Connection via QR Code
Then go „Next”.
Select the Wi-Fi network in which the camera will operate and enter the password of this network.
Point the camera at the QR code displayed in the app, click „I heard the sound” after the beep.
Wait for the app to configure the device with the selected Wi-Fi network.
Go „DONE”
The camera has been installed and displays the main interface.
Factory reset
To restore the default settings of the camera, hold down the Reset button for about 5 seconds until a beep sounds. Then release the button.
The camera will restart, restore the default (factory) settings and be ready to be added to the application again.
Technical specification
| Power supply | 230V AC |
| Communication | Wi-Fi 2.4GHz |
| Lumen | 2500 – 3000lm |
| Resolution | 4Mpx 2560*1440P |
| Storage | TF (micro SD) card not included (Max 256GB) |
| IP protection class | IP65 |
| Dimension [mm] | 283 x 133 x 184 |
Product Compliance
This product complies with the following EU Directives:
2014/53/EU, 2011/65/EU.
Producer:
Engo Controls sp. z o.o. sp. k.
4 St.
43-262 Poland
Documents / Resources
 |
ENGO CONTROLS ECAM-L2 Wi-Fi Smart Floodlight Camera [pdf] User Guide ECAM-L2 Wi-Fi Smart Floodlight Camera, ECAM-L2, Wi-Fi Smart Floodlight Camera, Smart Floodlight Camera, Floodlight Camera, Camera |
