Chii chinonzi Z-Wave?

Z-Wave ndiyo yepasirese isina waya protocol yekutaurirana muSmart Home. Izvi
mudziyo wakakodzera kushandiswa munharaunda yakataurwa muchikamu che Quickstart.

Z-Wave inovimbisa kutaurirana kwakavimbika nekusimbisa meseji yese (nzira mbiri
kutaurirana) uye ese mains powered node anogona kuita seanodzokorora mamwe ma node
(meshed network) kana iyo inogamuchira isiri yakananga isina waya renji ye
transmitter.

Ichi chishandiso uye chimwe nechimwe chakasimbiswa Z-Wave chishandiso chinogona kuva kushandiswa pamwe chete nezvimwe
yakasimbiswa Z-Wave mudziyo zvisinei nerudzi uye kwaakabva chero bedzi ari maviri akakodzera kune
zvakafanana frequency range.

Kana mudziyo unotsigira kukurukurirana kwakachengeteka ichataurirana nemimwe michina
yakachengeteka chero bedzi chigadziro ichi chinopa imwechete kana yakakwirira yehutano.
Zvikasadaro zvinongoerekana zvashanduka kuita yakaderera mwero wekuchengetedza kuchengetedza
kumashure kugarisana.

Kuti uwane rumwe ruzivo nezve Z-Wave tekinoroji, zvishandiso, machena mapepa nezvimwe ndapota tarisa
kune www.z-wave.info.

Product Description

Iyo SES303 sensor inopihwa simba kubva ku2XAA mabhatiri uye iri Z-Wave Plus certified. Pamusoro pekushanda kwakajairwa ivo vanotsigirawo imwe yeinotevera sarudzo yekumisikidza:

Imwe yekunze NTC wired tembiricha sensor (SES 001)

Mana ekunze ane waya pombi/tangi tembiricha sensors (SES 002) imwe neimwe yakabatana ne 1 mita kureba tambo.

Imwe yekunze wired pombi/tangi tembiricha sensor (SES 003), yakabatana netambo yemamita mana kureba.

Iyi unit yakanakira tembiricha uye humidity kuyerwa kweakangwara yepakati kudziyisa zvinodzora kana chero imwe yakafanana application. Yayo mushandisi interface yakatwasuka uye ine bhatani rekusundidzira uye chiratidzo che LED kudivi rekuseri, munhu anogona nyore kusanganisira / kusabvisa izvi kunetiweki yeZ-Wave.

Gadzirira Kuisa / Reset

Ndapota verenga bhuku rekushandisa usati waisa chigadzirwa.

Kuti ubatanidze (wedzera) mudziyo weZ-Wave kune network inofanira kunge iri mufekitari default
state. Ndokumbirawo muve nechokwadi chekuseta zvakare mudziyo mufekitari default. Unogona kuita izvi ne
kuita basa reKusabatanidzwa sezvinotsanangurwa pazasi mubhuku rekushandisa. Yese Z-Wave
controller inokwanisa kuita oparesheni iyi asi zvinokurudzirwa kushandisa yekutanga
mutongi weiyo yapfuura network kuti ave nechokwadi chekuti mudziyo wacho hauna kubatanidzwa nemazvo
kubva kune network iyi.

Installation

Chengetedza iyo SES 303 mupakiti yakavharwa kusvika guruva nemarara zvabviswa pamberi pekugadzira. Bvisa ndiro yemadziro kubva kumashure kweSES 303.

a) Iyo ndiro yemadziro inogona kuburitswa nekutsikirira zvimedu zvechitubu pazasi peplate remadziro

b) Paunenge uchidzvanya zvimedu zvechitubu, zunza madziro kunze uye pasi kuti ubvise.

Sarudza nzvimbo iyo iyo unit ichaiswa (tarisa kune inotevera marongero). Dzivisa nzvimbo padivi kana kuseri kwenzvimbo huru dzesimbi dzinogona kukanganisa masaini eredhiyo emagetsi akaderera pakati peyuniti nemutongi. Iyo sensor inofanirwa kuiswa pamadziro emukati, anenge 1.5 metres (5 tsoka) pamusoro pefloor level uye kure nekudonha, kwakananga kupisa masosi uye chiedza chezuva. Ita shuwa kuti pane nzvimbo yakakwana kutenderedza yuniti kuti ubvumire kupinda nyore kune maviri anochengeta echisipiti clips pagadziko remadziro ndiro. Zvingave zvakakosha kufambisa sensor kutenderedza kuti ive nechokwadi chekutaurirana kwakanaka. Usaedze kuiisa pamadziro kusvika yaiswa pane network.

Kubatanidzwa/Kusabatanidzwa

Pafekitori default mudziyo hausi weZ-Wave network. Chishandiso chinoda
kuva yakawedzerwa kune iripo isina waya network kutaurirana nemidziyo yetiweki iyi.
Iyi nzira inodaidzwa Kubatanidzwa.

Midziyo inogona zvakare kubviswa kubva kunetiweki. Iyi nzira inodaidzwa Kusabatanidzwa.
Maitiro ese ari maviri anotangwa neyekutanga controller yeZ-Wave network. Izvi
controller inoshandurwa kuita yekusabatanidzwa inoenderana inclusion mode. Kubatanidzwa uye Kusabatanidzwa ndiko
obva aita kuita yakakosha yemanyorero chiito pamudziyo.

Kubatanidzwa

Gadzirisa mabhatiri maviri eAAA anopihwa. Imba yebhatiri inoiswa chiratidzo chekuwedzera uye minus. Ita shuwa kuti bhatiri rega rega rakanyatsoenderana. Iyo SES 303 ikozvino ichasimudza.

Step 1: PaZ-Wave controller, sarudza Sanganisira kana iwe uri kuwedzera chishandiso kunetiweki kana sarudza Rega kana uri kubvisa mudziyo kubva kunetiweki. Tarisa nebhuku remugadziri wemugadziri.

Step 2: PaSES SES 303, dzvanya bhatani, bata uye sunungura mushure mesekondi 1 kutumira chikumbiro (Network Information Frame) yekubatana netiweki.

Pakubatanidzwa kwakabudirira iyo LED inopenya kaviri. Iyo yakazara maitiro inogona kutora kusvika kumasekonzi makumi maviri; refer to the ?Radio? chikamu cheruzivo. Kana iyo LED ichipenya 2-nguva izvi zvinoreva kuti maitiro ekubatanidza atadza, saka edza kufambisa iyo SES 20 kune imwe nzvimbo uye dzokorora Matanho eInclusion. Kana iyo yekusanganisa maitiro ikatadza zvakare, mudziyo unogona kunge watoverengerwa mune imwe network. Saka tanga usabvisa uye wozosanganisira mudziyo. Iyo controller icharatidza kana iyo yekusanganisa / Kusarudzika kushanda kwabudirira.

Kusabatanidzwa

Gadzirisa mabhatiri maviri eAAA anopihwa. Imba yebhatiri inoiswa chiratidzo chekuwedzera uye minus. Ita shuwa kuti bhatiri rega rega rakanyatsoenderana. Iyo SES 303 ikozvino ichasimudza.

Step 1: PaZ-Wave controller, sarudza Sanganisira kana iwe uri kuwedzera chishandiso kunetiweki kana sarudza Rega kana uri kubvisa mudziyo kubva kunetiweki. Tarisa nebhuku remugadziri wemugadziri.

Step 2: PaSES SES 303, dzvanya bhatani, bata uye sunungura mushure mesekondi 1 kutumira chikumbiro (Network Information Frame) yekubatana netiweki.

Pakubatanidzwa kwakabudirira iyo LED inopenya kaviri. Iyo yakazara maitiro inogona kutora kusvika kumasekonzi makumi maviri; refer to the ?Radio? chikamu cheruzivo. Kana iyo LED ichipenya 2-nguva izvi zvinoreva kuti maitiro ekubatanidza atadza, saka edza kufambisa iyo SES 20 kune imwe nzvimbo uye dzokorora Matanho eInclusion. Kana iyo yekusanganisa maitiro ikatadza zvakare, mudziyo unogona kunge watoverengerwa mune imwe network. Saka tanga usabvisa uye wozosanganisira mudziyo. Iyo controller icharatidza kana iyo yekusanganisa / Kusarudzika kushanda kwabudirira.

Kushandiswa Kwechigadzirwa

Iyo yekudyidzana maitiro inoshanda chete mushure mekunge mudziyo wasanganisirwa mune network. Ndokumbira utarise kuti mamwe ma controller anogona kungozvibatanidza. Gara uchitarisa nemanyorero emugadziri.

Nhanho 1: Isa mutongi muKushamwaridzana Mode.

Step 2: Dzvanya uye bata SES 303 bhatani kweanopfuura 1 sekondi wobva wasunungura.

Nhanho 3: Mutongi anosimbisa kushamwaridzana kana maitiro apera.

RF kutaurirana cheki mushure mekuisa Dzvanya bhatani kwenguva isingasviki 1 sekondi. Iyo SES 303 inotumira tembiricha mushumo weonboard sensor. Ongorora: iyi ficha inoshanda chete kana mudziyo waiswa munetiweki uye node dzakabatana. Kutumira Node Ruzivo- Dzvanya uye bata SES 303 bhatani kweinopfuura 1 sekondi wobva wasunungura.

Kukurumidza dambudziko kupfura

Heano mashoma mazano ekuisa network kana zvinhu zvikasashanda sezvaitarisirwa.

1. Ita shuwa kuti mudziyo uri mufekitori reset mamiriro usati wasanganisira. Mukupokana usabvisa pamberi sanganisira.
2. Kana kusanganisirwa kuchiri kutadza, tarisa kana zvese zvishandiso zvinoshandisa ma frequency akafanana.
3. Bvisa zvese zvakafa kubva kumasonganiro. Zvikasadaro uchaona kunonoka kwakanyanya.
4. Usamboshandisa bhatiri midziyo yekurara isina yepakati controller.
5. Usavhote FLIRS zvishandiso.
6. Ita shuwa kuti une yakakwana mains powered mudziyo kuti ubatsirwe kubva kune meshing

Kushamwaridzana - imwe mudziyo inodzora imwe mudziyo

Z-Wave zvishandiso zvinodzora zvimwe Z-Wave zvishandiso. Ukama pakati pemudziyo mumwe
kudzora mumwe mudziyo kunonzi kushamwaridzana. Kuti udzore zvakasiyana
mudziyo, mudziyo unodzora unofanirwa kuchengetedza runyoro rwemidziyo inogashira
kudzora mirairo. Aya mazita anonzi mapoka ekubatana uye anogara aripo
zvine chekuita nezvimwe zviitiko (semuenzaniso bhatani rakadzvanywa, sensor trigger, ...). Zvikazo
chiitiko chinoitika ese maturusi akachengetwa muboka rekubatana achaita
gamuchira imwechete isina waya yekuraira isina waya, kazhinji iyo 'Basic Set' Command.

Mapoka eMasangano:

Nhamba YebokaMaximum NodesDescription

1

2

Configuration Parameters

Z-Wave zvigadzirwa zvinofanirwa kushanda kunze kwebhokisi mushure mekuiswa, zvisinei
kumwe kugadziridzwa kunogona kugadzirisa basa zvirinani kune zvinodiwa nemushandisi kana kuvhura mberi
kuvandudzwa maitiro.

ZVINOKOSHA: Vadzori vanogona chete kubvumidza kugadzirisa
dzakasaina tsika. Kuti uise kukosha muhuwandu 128 ... 255 kukosha kwakatumirwa mukati
chikumbiro chichava kukosha kunodiwa kubvisa 256. For example: Kuisa a
parameter kusvika 200  ingangodiwa kuseta kukosha kwe200 minus 256 = minus 56.
Kana iri mbiri yebhayiti kukosha kwakafanana kunoshanda: Values ​​yakakura kupfuura 32768 inogona
inoda kupihwa sehunhu husina kunaka zvakare.

Parameter 1: Delta Tembiricha

Saizi: 1 Byte, Default Value: 0

SettingDescription

1-125	0,1 - 12,5 “°C
130-255	-0,1 – -12,5 “°C

Parameter 2: Yenguva Yekubika Yenguva

Saizi: 1 Byte, Default Value: 5

SettingDescription

1-255

Nguva mumaminiti

Parameter 3: Delta Humidity

Saizi: 1 Byte, Default Value: 5

SettingDescription

1-125	0,1 - 12,5 %RH
130-255	-0,1 – -12,5 %RH

Parameter 4: Humidity Reporting Interval

Saizi: 1 Byte, Default Value: 5

SettingDescription

1-255

Nguva mumaminiti

Technical Data

Dimensions	0.0850000×0.0850000×0.0310000 mm
Kurema	160 gr
EAN	5015914840098
Device Type	Kugadzirisa Multilevel Sensor
Kirasi Yekushandisa Yechigadzirwa	Multilevel Sensor
Specific Device Kirasi	Kugadzirisa Multilevel Sensor
Firmware Shanduro	01.00
Z-Wave Vhezheni	03.5f
Chitupa ID	ZC10-15010003
Z-Wave Chigadzirwa Id	0059.000d.0003
Frequency	Europe - 868,4 Mhz
Maximum transmission simba	5 mW

Inotsigirwa Command Classes

• Basic
• Switch Multilevel
• Sangano Grp Info
• Device Reset Local
• Zvaveplus Info
• Configuration
• Manufacturer Specific
• Powerlevel
• Bhatiri
• Muka
• Kushamwaridzana
• Version

Tsanangudzo yeZ-Wave chaiyo mazwi

• Controller - iri Z-Wave mudziyo une kugona kubata network.
  Ma controller anowanzo magedhi, Remote Controls kana bhatiri rinoshandiswa madziro controller.
• Muranda - iri Z-Wave chishandiso chisina kugona kubata network.
  Varanda vanogona kunge vari masensa, actuators uye kunyange kure kure.
• Primary Controller - ndiye murongi wepakati wetiweki. Zvinofanira kuva
  controller. Panogona kuve nemutongi mumwe chete wekutanga muZ-Wave network.
• Kubatanidzwa - ndiyo maitiro ekuwedzera michina mitsva yeZ-Wave mune network.
• Kusabatanidzwa - ndiyo maitiro ekubvisa Z-Wave zvishandiso kubva kunetiweki.
• Kushamwaridzana - hukama hwekutonga pakati pemudziyo unodzora uye
  mudziyo unodzorwa.
• Wakeup Chiziviso -imeseji yakakosha isina waya yakapihwa neZ-Wave
  mudziyo wekuzivisa unokwanisa kutaura.
• Node Information Frame -imeseji yakakosha isina waya inoburitswa nea
  Z-Wave mudziyo kuzivisa kugona kwayo uye mabasa.