PPI LabCon Multi-Purpose Temperature Controller User Manual

LabCon
Multi-Purpose Temperature Controller
Operation Manual

Zviri mukati hide

1 LabCon Multi-Purpose Temperature Controller

2 OPERATOR PEJI PARAMETERS

3 KUKUNGAMIRIRA KWEMAGETSI

4 FRONT PANEL KEYS

5 Zvinyorwa / Zvishandiso

5.1 References

6 Related Posts

LabCon Multi-Purpose Temperature Controller

Iri bhuku ripfupi rinonyanya kuitirwa kukurumidza kutaridza kune wiring connections uye parameter kutsvaga. Kuti uwane mamwe mashoko pamusoro pekushanda uye kushandiswa; ndapota pinda pa www.ppiindia.net

OPERATOR PEJI PARAMETERS

Parameters	Settings (Default Value)
Time Start Command >> Time Abort Command >>	Hongu Kwete (Default: Kwete)
Nguva Yenguva (H:M) >>	0.00 kusvika 500.00 (HH:MM) (Default: 0.10)
Ctrl Set Kukosha >>	Setpoint LO muganho kune Setpoint HI muganho (Resolution 0.1°C yeRTD / DC Linear & 1°C yeThermocouple) (Default: 25.0)
Ctrl Lo Kutsauka >>	YeRTD & DC Linear: 0.2 kusvika 99.9 YeThermocouple: 2 kusvika 99 (Default: 2.0)
Ctrl Mhoro Kutsauka >>	YeRTD & DC Linear: 0.2 kusvika 99.9 YeThermocouple: 2 kusvika 99 (Default: 2.0)
Chinja password >>	1 kusvika 100 (Default: 0)

SUPERVISORY > SENSOR INPUT

Parameters	Settings (Default Value)
Ctrl Zero Offset >>	-50 kusvika ku50 (Resolution 0.1°C yeRTD / DC Linear & 1°C yeThermocouple) (Default: 0.0)

SUPERVISORY > KUDZORA

Parameters	Settings (Default Value)
Tune >>	Hongu Kwete (Default: Kwete)
Setpoint LO Limit >>	Min Range yeYakasarudzwa Yekupinza Rudzi kuSetpoint HI Limit (Chisarudzo 0.1°C cheRTD/ DC Linear & 1°C yeThermocouple) (Default: 0.0)
Setpoint HI Limit >>	Setpoint LO Limit kuMax Range yeVakasarudzwa Input Type (Resolution 0.1°C yeRTD / DC Linear & 1°C yeThermocouple) (Default: 600.0)
Compressor Setpoint >>	0 kusvika 100 (Resolution 0.1°C yeRTD / DC Linear & 1°C yeThermocouple) (Default: 45.0)
Compressor Hyst >>	0.1 kusvika 99.9 (Default: 2.0)
Kupisa Ctrl Chiito >>	ON-OFF PID (Default: PID)
Kupisa Hyst >>	0.1 kusvika 99.9 (Default: 0.2)

Kupisa Chete Kudzora	Kupisa + Kunotonhorera Kudzora Zone: Imwe	Kupisa + Kunotonhorera Kudzora Zone: Dual
Proportional Band >> 0.1 kusvika 999.9 (Default: 50.0)	Proportional Band >> 0.1 kusvika 999.9 (Default: 50.0)	Cz Prop Band >> Proportional Band yeKutonhorera Pre-inotonga zone 0.1 kusvika 999.9 (Default: 50.0)
Integral Time >> 0 kusvika 3600 sec (Default: 100 sec)	Integral Time >> 0 kusvika 3600 sec (Default: 100 sec)	Cz Integral Nguva >> Yakakosha Nguva Yekutonhorera Pre-inotonga nzvimbo 0 kusvika 3600 sec (Default: 100 sec)
Derivative Time >> 0 kusvika 600 sec (Default: 16 sec)	Derivative Time >> 0 kusvika 600 sec (Default: 16 sec)	Cz Derivative Time >> Nguva Yakatorwa Yekutonhorera Pre-inotonga nzvimbo 0 kusvika 600 sec (Default: 16 sec)
Cycle Time >> 0.5 kusvika 100.0 sec (Default: 10.0 sec)	Cycle Time >> 0.5 kusvika 100.0 sec (Default: 10.0 sec)	Hz Prop Band >> Proportional Band yeHeat Pre-dominant zone 0.1 kusvika 999.9 (Default: 50.0)
Overshoot Inhibit >> Gonesa Disable (Default: Disable)	Overshoot Inhibit >> Gonesa Disable (Default: Disable)	Hz Yakakosha Nguva >> Yakakosha Nguva Yekupisa Pre-inotonga nzvimbo 0 kusvika 3600 sec (Default: 100 sec)
Cutoff Factor >> 1.0 kusvika 2.0 sec (Default: 1.2 sec)	Cutoff Factor >> 1.0 kusvika 2.0 sec (Default: 1.2 sec)	Hz Derivative Time >> Nguva Yekutorwa Yekupisa Pre-inotonga zone 0 kusvika 600 sec (Default: 16 sec)
		Cycle Time >> 0.5 kusvika 100.0 sec (Default: 10.0 sec)
		Overshoot Inhibit >> Gonesa Disable (Default: Disable)
		Cutoff Factor >> 1.0 kusvika 2.0 sec (Default: 1.2 sec)

SUPERVISORY > PASSWORD

Parameters	Settings (Default Value)
Chinja password >>	1000 kusvika 1999 (Default: 123)

SUPERVISORY > BUDA

Parameters	Settings (Default Value)
Buda Setup Mode >>	Hongu Kwete (Default: Kwete)

FACTORY > KUDZORA SENSOR INPUT

Parameters

Settings (Default Value)

Input Type >>

Refer Tafura 1
(Default: RTD Pt100)

Chiratidzo LO >>

Input Type	Settings	Default
0 kusvika 20mA	0.00 kuenda kuSignal High	0.00
4 kusvika 20mA	4.00 kuenda kuSignal High	4.00
0 kusvika ku5v	0.000 kuenda kuSignal High	0.000
0 kusvika ku10v	0.00 kuenda kuSignal High	0.00
1 kusvika ku5v	1.000 kuenda kuSignal High	1.000

Signal HI >>

Input Type	Settings	Default
0 kusvika 20mA	Signal Yakaderera kusvika 20.00	20.00
4 kusvika 20mA	Signal Yakaderera kusvika 20.00	20.00
0 kusvika ku5v	Signal Yakaderera kusvika 5.000	5.000
0 kusvika ku10v	Signal Yakaderera kusvika 10.00	10.00
1 kusvika ku5v	Signal Yakaderera kusvika 5.000	5.000

Range LO >>

-199.9 kusvika RANGE HI
(Default: 0.0)

Range HI >>

RANGE LO kusvika 999.9
(Default: 100.0)

FACTORY > ALARM PARAMETERS

Parameters	Settings (Default Value)
Hysteresis >>	0.1 kusvika 99.9 (Default: 0.2)
Inhibit >>	Hongu Kwete (Default: Hongu)

FACTORY > HEAT COOL SARUDZA

Parameters	Settings (Default Value)
Kudzora Strategy >>	Kupisa Kungotonhorera Chete Kupisa + Kutonhorera (Default: Kupisa + Kutonhorera)
Kudzora Strategy: Kutonhorera Chete
Nguva Kunonoka (sec) >>	0 kusvika 1000 Sec (Default: 200 Sec)
Kudzora Strategy: Kupisa + Kutonhorera
Compressor Strategy >>	CONT. OFF CONT. PANE SP YAKABVA PV YAKABVA (Default: CONT. ON)

CONT. ON	SP BASED	PV BASED
Nguva Kunonoka (sec) >> 0 kusvika 1000 Sec (Default: 200 Sec)	Boundary Set Value >> 0 kusvika 100 (Resolution 0.1°C yeRTD / DC Linear & 1°C yeThermocouple) (Default: 45.0)	Nguva Kunonoka (sec) >> 0 kusvika 1000 Sec (Default: 200 Sec)
	Control Zones >> Single Dual (Default: Single)
	Nguva Kunonoka (sec) >> 0 kusvika 1000 Sec (Default: 200 Sec)

Parameters	Settings (Default Value)
Holdback Strategy >>	Hapana Pamusoro Pazasi Maviri (Default: Hapana)
Bata Band >>	0.1 kusvika 999.9 (Default: 0.5)
Heat Off >>	Kwete Hongu (Default: Kwete)
Cool Off >>	Kwete Hongu (Default: Kwete)
Kudzoreredza Simba >>	Abort Restart Continuous (Default: Tangazve)

FACTORY > DOOR VAKAZARURWA

Parameters	Settings (Default Value)
Gonesa >>	Hongu Kwete (Default: Kwete)
Chinja Logic >>	Vhara: Door Vhura Vhura: Door Vhura (Default: Vhara: Door Vhura)
Door Alrm Dly (sec) >>	0 kusvika 1000 Sec (Default: 60 Sec)

Fekitari > MAINS KUKNDIKANA

Parameters	Settings (Default Value)
Gonesa >>	Hongu Kwete (Default: Kwete)
Chinja Logic >>	Vhara: Mains Fail Open: Mains Fail (Default: Vhara: Mains Fail)

FACTORY > PASSWORD

Parameters	Settings (Default Value)
Chinja password >>	2000 kusvika 2999 (Default: 321)

FACTORY > FACTORY DEFAULT

Parameters	Settings (Default Value)
Set To Default >>	Hongu Kwete (Default: Kwete)

FACTORY > BUDA

Parameters	Settings (Default Value)
Buda Setup Mode >>	Hongu Kwete (Default: Kwete)

TAFURA 1

Zvazvinoreva	Range (Min. kusvika Max.)	Resolution
Nyora J Thermocouple	0 kusvika +960°C	Yakagadziriswa 1°C
Tora K Thermocouple	-200 kusvika +1376°C
Tora T Thermocouple	-200 kusvika +385°C
Nyora R Thermocouple	0 kusvika +1770°C
Nyora S Thermocouple	0 kusvika +1765°C
Type B Thermocouple	0 kusvika +1825°C
Nyora N Thermocouple	0 kusvika +1300°C
Reserve	Yakachengeterwa mutengi chaiwo Thermocouple mhando isina kunyorwa pamusoro. Rudzi urwu ruchatsanangurwa zvinoenderana neyakarairwa (inosarudza pachikumbiro) Thermocouple mhando.
3-waya, RTD PT100	-199.9 kusvika ku600.0 ° C	Yakagadziriswa 0.1°C
0 kusvika 20mA DC ikozvino	-199.9 kusvika 999.9 zvikamu	Fixed 0.1 chikwata
4 kusvika 20mA DC ikozvino
0 kusvika 5.0V DC voltage
0 kusvika 10.0V DC voltage
1 kusvika 5.0V DC voltage

KUKUNGAMIRIRA KWEMAGETSI

FRONT PANEL KEYS

Symbol	Key	Function
	Mupumburu	Dzvanya kuti upururudze kuburikidza neakasiyana Maitiro eRuzivo Screens mune Yakajairika Operation Mode.
	Alarm Bvuma	Dzvanya kuti ubvume uye unyaradze (kana uchishanda) alarm kubuda.
	PASI	Dzvanya kuti uderedze kukosha kweparameter. Kudzvanya kamwe kunoderedza kukosha nekuverenga kumwe; kuramba wakadzvanya kunomhanyisa shanduko.
	UP	Dzvanya kuti uwedzere kukosha kweparameter. Kudzvanya kamwe kunowedzera kukosha nekuverenga kumwe; kuramba wakadzvanya kunomhanyisa shanduko.
	GADZIRIRA	Dzvanya kuti upinde kana kubuda mumodhi yekuseta.
	PINDA	Dzvanya kuti uchengetedze iyo yakatarwa parameter kukosha uye kupuruzira kune inotevera paramende.

PV ERROR ZVIRATIDZO

Mharidzo	Rudzi rweKanganiso	Chikonzero
	Sensor Open	Sensor (RTD Pt100) Yakaputsika / Yakavhurika
	Pamusoro-renji	Tembiricha iri pamusoro peMax. Specified Range
	Under-range	Tembiricha iri pasi peMin. Specified Range

101, Diamond Industrial Estate, Navghar,
Vasai Road (E), Dist. Palghar - 401 210.
Sales : 8208199048 / 8208141446
Support : 07498799226 / 08767395333
E: sales@ppiindia.net
support@ppiindia.net
Ndira 2022

Zvinyorwa / Zvishandiso

PPI LabCon Multi-Purpose Temperature Controller [pdf] User Manual
LabCon Multi-Purpose Temperature Controller, LabCon, Multi-Purpose Temperature Controller, Temperature Controller, Controller

References

User Manual