Altronix eFlow104NKA8QM Series Networkable Dual Output Access Power Controllers

Nhoroondo ye eFlow104NKA8QM
Networkable Dual Output
Svika Power Controllers
Mienzaniso Inosanganisira:
eFlow104NKA8QM

• 12VDC kana 5VDC inosvika 6A uye/kana 24VDC inosvika 10A (240W yakazara simba) inosarudzwa nekubuda.
• Sere (8) programmable fuse yakachengetedzwa zvabuda
• Zvisere (8) zvinokonzeresa zvinokonzeresa zvinopinza
• Yakavakirwa-mukati Charger yemabhatiri emhando yelead akavharwa

eFlow104NKA8DQM

• 12VDC kana 5VDC inosvika 6A uye/kana 24VDC inosvika 10A (240W yakazara simba) inosarudzwa nekubuda.
• Eight (8) programmable Kirasi 2 simba-shoma PTC yakachengetedzwa zvinobuda
• Zvisere (8) zvinokonzeresa zvinokonzeresa zvinopinza
• Yakavakirwa-mukati Charger yemabhatiri emhando yelead akavharwa

Installation Guide

Rev. eFlow104NKA8Q-072720 Kupfuura simba chete.TM Kuisa Kambani: _______________ Service Rep. Zita: _____________________________________________ Kero: _____________________________________________ Phone #: ______________________________

Overview:
Altronix eFlow104NKA8QM uye eFlow104NKA8DQM kugovera uye kushandura simba kuti uwane masystem ekudzora uye zvishongedzo. Ivo vanoshandura 120VAC 60Hz yekupinda kuita sere (8) yakazvimirira inodzorwa 12VDC kana 24VDC yakachengetedzwa inobuda. Access Power Controller's mbiri yekuisa dhizaini inobvumira simba kuti ritungamirirwe kubva kune mbiri (2) fekitori yakaiswa yakazvimirira yakaderera vol.tage 12 kana 24VDC Altronix magetsi ekupa kune masere (8) akazvimirira anodzora fuse (eFlow104NKA8QM) kana PTC (eFlow104NKA8DQM) akachengetedzwa zvabuda. Simba rinobuda rinogona kushandurwa kuita yakaoma fomu "C" mazita. Mabudiro anoitwa neakavhurika muunganidzi sink, anowanzo kuvhurika (NO), anowanzo kuvharwa (NC) yakaoma trigger yekuisa, kana nyoro inobuda kubva kuAccess Control System, Card Reader, Keypad, Push Button, PIR, etc. eFlow104NKA8(D) QM ichafambisa simba kune zvakasiyana-siyana zvekupinda kutonga hardware zvishandiso zvinosanganisira Mag Locks, Electric Strikes, Magnetic Door Holders, etc. Outputs ichashanda mune zvose Fail-Safe uye / kana Fail-Secure modes. Iyo FACP Interface inogonesa Emergency Egress, Alarm Monitoring, kana inogona kushandiswa kumutsa mimwe michina yekubatsira. Iyo yemoto alarm yekubvisa ficha inosarudzwa yega kune chero kana ese masere (8) zvinobuda. Iyo spade yekubatanidza inokutendera iwe kuti daisy cheni simba kune akawanda LINQ8ACM (CB) modules. Iyi ficha inobvumidza iwe kugovera simba pamusoro pezvakawanda zvinobuda kune makuru masisitimu. Yakavakirwa-mukati LINQTM Network Power Management inofambisa kutarisa, kushuma uye kutonga kwesimba / kuongororwa.

Zvinodiwa:
Zvinopinza
eFlow104NB:

• 120VAC, 60Hz, 4.5A.

LINQ8ACM(CB):

• Zvisere (8) zvinokonzeresa:
  1. Kazhinji kuvhurika (NO) zvekushandisa (dry contacts).
  2. Kazhinji yakavharwa (NC) mapipu (dry contacts).
  3. Vhura zvekuunganidza sink inputs.
  4. Wet Input (5VDC - 24VDC) ine 10K resistor
  5. Chero kusanganiswa kwezviri pamusoro.

Zvinobuda:
Simba:

• 12VDC kana 5VDC kusvika 6A, 24VDC kusvika 10A (240W yakazara simba).
• Yekubatsira Kirasi 2 simba-rinogumira kuburitsa yakatemerwa @ 1A (isina kumiswa).
• Kupfuuratage kudzivirirwa.

LINQ8ACM:

• Fuse yakadzivirirwa inobuda yakatemerwa @ 2.5A pane inobuda, isina simba-inogumira. Zvose zvinobuda 6A max.

LINQ8ACMCB:

• PTC yakadzivirirwa zvinobuda zvakatemerwa @ 2A pane inobuda, Kirasi 2 simba-rishoma. Zvose zvinobuda 6A max. Usapfuure chiyero chemagetsi ega ega.
• Zvisere (8) zvinosarudzwa zvakazvimiririra zvinodzorwa zvinobuda kana zvisere (8) zvinodzorwa zvisina kufanira Fomu "C" relay mabudiro (ona pazasi kuti uwane ratings):
  1. Fail-Safe uye/kana Fail-Chengetedza magetsi kubuda.
  2. Ebetsero magetsi anobuda (un switched).
  3. Chero kusanganiswa kwezviri pamusoro.
•  Yega inobuda inogona kusetwa kune OFF chinzvimbo chesevhisi (output jumper yakaiswa kune yepakati chinzvimbo). Haishande kune Dry Contact application.
• Chero pazvisere (8) fuse/PTC akadzivirirwa magetsi anobuda anosarudzwa kutevera magetsi Input 1 kana Input 2. Output voltage yega yega inobuda yakafanana neyekuisa voltage yezvakasarudzwa.
• Surge kudzvinyirira.

Fuse/PTC Ratings:
eFlow104NB:

• Fuse inopinza inonzi 6.3A/250V. Battery fuse inonzi 15A/32V. LINQ8ACM:
• Fuse huru yekupinza yakayerwa 15A/32V. Mafiyuzi anobuda akatemerwa 3A/32V.

LINQ8ACMCB:

• Main input PTC yakarongwa 9A. Kubuda kwePTCs kwakarongwa 2A.

Battery Backup (eFlow104NB):

• Yakavakirwa-mukati charger yeakavharirwa lead asidhi kana gel mhando mabhatiri.
• Maximum charge ikozvino 1.54A.
• Chinja otomatiki kune bhatiri rakamira kana AC yatadza. Kuendesa kune yakamira-nebhatiri simba rinobva ipapo pasina kukanganisa.

Kutarisira (eFlow104NB):

• AC inotadza kutarisa (fomu "C" mazita).
• Bhatiri rakundikana & kutarisa kuvapo (fomu "C" mazita).
• Kudzima kwemagetsi mashoma. Inodzima DC inobuda zviteshi kana bhatiri voltage inodonha pazasi 71-73% ye12V mayunitsi uye 70-75% ye24V mayunitsi (zvichienderana nemagetsi). Inodzivirira kubuda kwebhatiri rakadzika.

Moto Alarm Dimbura: eFlow104NB:

• Inotariswa Moto Alarm bvisa (latching kana isina-latching) 10K EOL resistor. Inoshanda pane inowanzovhurika (NO) kana inowanzovharwa (NC) trigger.

LINQ8ACM(CB):

• Moto Alarm disconnect (latching kana kusa-latching) inosarurwa yega kune chero kana ese ezvisere (8) zvinobuda. Moto Alarm bvisa sarudzo dzekuisa:
  • Kazhinji kuvhura [NO] kana kuvharika [NC] yakaoma kuonana yekupinda. Polarity reversal input kubva kuFACP signing circuit.

• FACP yekupinda WET yakayerwa 5-30VDC 7mA.
• FACP yekupinda EOL inoda 10K kupera kwemutsara wekupokana.
• FACP inoburitsa relay [NC]: Pamwe Dry 1A/28VDC, 0.6 Power Factor kana 10K kuramba ne [EOL JMP] yakasimba.

Zvinoonekwa Zviratidzo: eFlow104NB:

• Green AC LED:                   Inoratidza 120VAC iripo.
• Red DC LED:                      Inoratidza DC kubuda.
• LINQ8ACM(CB):
• Green AC LED:                   Inoratidza AC dambudziko mamiriro.
• Green BAT LED:                Inoratidza dambudziko rebhatiri.
• Green FACP LED:              Inoratidza kuti FACP disconnect yatanga.
• Kupenya kweBlue
  Kurova kwemoyo LED:                  Inoratidza network network.
• Individual
  OUT1 – OUT8
  Red LEDs:                           Ratidza zvinobuda zviri kukonzeresa.
• Individual
  Voltage LEDs:                     Ratidza 12VDC (Green) kana 24VDC (Red). (ona peji 5 yeLINQ8ACM(CB) LED Diagnostics).

Programmable Features (LINQ8ACM(CB)):

• Zvisere (8) zvinorongwa zvinobuda:
  • Kutadza-kuchengetedzeka, kutadza-kuchengetedzeka kana ebetsero zvabuda.
  • Kupinza kunodzorwa kana kudzorwa nemaoko kuburikidza nesoftware.
  • Pamusoro (pamusoro) uye pasi (pasi) voltage uye yekutarisa ikozvino nekubuda.
  • Zvakawanda zvinobuda zvinogona kurongwa kuti zviitwe nekuisa kamwe chete.
  • Battery back-up nekubuda.
• Zvisere (8) zvinokonzeresa zvinokonzeresa zvinopinza:
  • Kazhinji kuvhurika (NO).
  • Kazhinji yakavharwa (NC).
  • Vhura zvekuunganidza sink inputs.
  • Wet Input (5VDC - 24VDC) ine 10k resistor.
  • Chero kusanganiswa kwezviri pamusoro.
• Programmable port IDs.
• Monitor power supply(ies) yekupinda voltage uye miganhu yakarurama (yakakwirira / yakaderera).
• Input and output current calibration.
• Programmable timer zviitiko.
• Programmable mushandisi mwero.
• Bvumira kana kudzima chenjedzo nemhando.
• Programmable yambiro yekuzivisa kunonoka/

Environmental:

• Kushanda tembiricha: 0ºC kusvika 49ºC ambient.
• Humidity: 20 kusvika 85%, isina-condensing.

Enclosure Dimensions (inenge H x W x D): 15.5" x 12" x 4.5" (393.7mm x 304.8mm x 114.3mm).
eFlow104NKA8DQM Kuisa Gwaro

Stand-by Specifications:

Bhatiri	Burg. Zvikumbiro 4 awa. Mira ne/ 15 min. Alarm	Fire Applications 24 hr. Mira ne/ 5 min. Alarm	Access Control Applications Stand-by
7AH	0.4A/10A	N/A	5 mins./10A
12AH	1A/10A	0.3A/10A	15 mins./10A
40AH	6A/10A	1.2A/10A	Kupfuura 2 Maawa/10A
65AH	6A/10A	1.5A/10A	Kupfuura 4 Maawa/10A

Installation Instruction:
Wiring nzira dzichaenderana neNational Electrical Code/NFPA 70/NFPA 72/ANSI, Canadian Electrical Code uye nemakodhi ese emuno nezviremera zvine masimba. Chigadzirwa chakagadzirirwa kushandiswa kwemukati chete.

1. Mount unit munzvimbo yaunoda. Maka uye gadzira maburi mumadziro kuti uenderane nepamusoro makiyi maburi ari mukati mekuvharirwa. Isa zvisungo zviviri zvekumusoro nema screws mumadziro ane sikuruwa misoro yakabuda. Isa chivharo chepamusoro makiyi maburi pamusoro pemasikiru maviri epamusoro, nhanho uye chengetedza. Maka nzvimbo yemaburi maviri ezasi. Bvisa yakavharirwa. Dhobora maburi ezasi uye woisa ma fasteners maviri. Isa makiyi epamusoro emuvharo pamusoro pemakona maviri epamusoro. Isa maviri ezasi screws uye ita shuwa kuomesa ese screws
   (Enclosure Dimensions, p. 8). Chengetedza yakavharirwa pasi pevhu.
2. Ita shuwa kuti zvese zvinobuda zvinosvetuka [OUT1] - [OUT8] zvakaiswa mu OFF (pakati) chinzvimbo (Fig. 1, pg. 4).

1. Batanidza un switched AC power (120VAC 60Hz) kumaterminals akaiswa [L, N] (Fig. 2a, pg. 6). Green "AC" LED pane magetsi bhodhi inobatidza. Chiedza ichi chinogona kuoneka kuburikidza nelenzi ye LED pamusuwo weiyo yakavharirwa. Shandisa 14 AWG kana yakakura kune ese magetsi ekubatanidza. Chengetedza green wire lead kune ivhu pasi. Chengetedza wiring isina simba-yakaganhurwa kubva kune isina simba-inogumira wiring (120VAC 60Hz Input, Battery Wire). Minimum 0.25” nzvimbo inofanira kupihwa. CHENJERERO: Usabata nhengo dzesimbi dziri pachena. Vhara simba redunhu rebazi usati waisa kana kusevha midziyo. Iko hakuna zvikamu zvinoshandiswa nemushandisi mukati. Revera kuisirwa uye sevhisi kune vanokwanisa sevhisi vashandi.
2. Isa imwe neimwe inobuda [OUT1] - [OUT8] kunzira simba kubva Input 1 kana 2 (Fig. 1, pg. 4).
   Cherechedza: Kuyera kubuda voltage pamberi pekubatanidza zvishandiso. Izvi zvinobatsira kudzivisa kukanganisa kunogona kuitika.
3. Dzima simba usati wabatanidza zvishandiso.
4. Sarudzo dzezvinobuda: eFlow104NKA8DQM ichapa anosvika masere (8) akachinja magetsi anobuda pamwe nesere (8) un switched ebetsero magetsi anobuda. Yakachinja Magetsi emagetsi: Batanidza iyo isina kunaka (-) yekuisa yemudziyo uri kufambiswa kune terminal yakanyorwa [COM].
5. YeFail-Safe operation batanidza iyo yakanaka (+) inopinza yemudziyo uri kufambiswa kune terminal yakanyorwa [NC].
6. YeFail-Secure operation batanidza iyo yakanaka (+) yekupinda yemudziyo uri kufambiswa kune terminal yakanyorwa [NO].
   Ebetsero Simba Mabudisi (asina kuchinjirwa):Batanidza zvakanaka (+) mugadziriso wemudziyo uri kufambiswa kuterminal yamaka [C] uye yakaipa (-) yemudziyo uri kufambiswa kuterminal yakamaka [COM]. Kubuda kunogona kushandiswa kupa simba kune vaverengi vemakadhi, keypads nezvimwe.
   
7. Batidza simba guru mushure mekunge zvishandiso zvese zvabatanidzwa.
8. Input Trigger Options (chirongwa chinokonzeresa sarudzo dzekuisa kuburikidza neLINQ software):
   Cherechedza: Kana Fire Alarm ikadimburwa ikasashandiswa, batanidza chinodzivirira che10 k Ohm kune materminal akaiswa [GND neEOL]. Kupinza: Batanidza yakaoma yekupinda control (NC/NO) yekuisa kumaterminal akaiswa [+ INP1 -] ku [+ INP8 -]. Vhura Yekuunganidza Sink Input: Batanidza yakavhurika yekuunganidza sink yekuisa kune terminal yakanyorwa [+ INP1 -] ku [+ INP8 -]. Mvura (Voltage) Input Configuration: Kunyatsocherechedza polarity, batanidza voltage input trigger waya uye yakapihwa 10K resistor kumaterminals akaiswa [+ INP1 –] ku [+ INP8 –].
9. Fire Alarm Interface Options (chirongwa chemoto aramu interface sarudzo kuburikidza neLINQ software): Iyo inowanzovharwa [NC], inowanzovhura [NO] yekupinda kana polarity reversal yekupinda kubva kuFACP siginecha wedunhu inokonzeresa zvakasarudzwa. Kazhinji
   Vhura Zviripo:
   Waya yako FACP relay uye 10K resistor in parallel pamaterminals akaiswa [GND] uye [EOL].
   Kazhinji Yakavharwa Inopinza:
   Waya yako FACP relay uye 10K resistor munhevedzano pamaterminal akanyorwa [GND] uye [EOL].
   
10. FACP Dry NC yakabuda:
    Batanidza mudziyo waunoda kuti ukonzereswe neiyo unit yakaoma yekubatanidza inobuda kune materminal akaiswa [NC] uye [C]. Kana [EOL JMP] iri munzvimbo yeDIS, inobuda ndeye 0 Ohm kuramba mune yakajairika mamiriro. Kana [EOL JMP] iri munzvimbo yeEN, 10k kuramba ichapfuudzwa kune chinotevera chishandiso kana chiri mune yakajairika mamiriro.
11. Stand-by Battery Connections (Fig. 3, pg. 7, Fig. 4, pg. 8): Kune US Access Control applications mabhatiri anosarudzwa. Mabhatiri anodiwa pakuisirwa kweCanada (ULC-S319). Kana mabhatiri akasashandiswa, kurasikirwa kwe AC kunozokonzera kurasikirwa kwekubuda kwevoltage. Kana kushandiswa kwema-stand-by mabhatiri kunodiwa, anofanira kunge ari lead acid kana gel rudzi. Batanidza bhatiri kune LINQ8ACM(CB)'s materminal akanyorwa [+ BAT –] (Fig. 3, pg. 7). Shandisa maviri (2) 12VDC mabhatiri akabatanidzwa munhevedzano ye24VDC oparesheni (yebhatiri inotungamira inosanganisirwa). Shandisa mabhatiri Cavil CL1270 (12V/7AH), CL12120 (12V/12AH), CL12400 (12V/40AH), CL12650 (12V/65AH) mabhatiri kana UL anozivikanwa BAZR2 neBAZR8 mabhatiri echiyero chakakodzera.
12. Battery uye AC Supervision zvabuda (Fig. 3, p. 7, Fig. 4, p. 8): eFlow104NB ifekitari yakabatana neLINQ8ACM (CB) yeBattery uye AC kutarisira.
13. Kunonotsa AC kushuma kwemaawa maviri. isa DIP chinja [AC Kunonoka] kune OFF chinzvimbo (Fig. 2c, pg. 2). Kunonotsa AC kushuma kwe6 min. isa DIP chinja [AC Kunonoka] kune ON chinzvimbo (Fig. 1c, pg. 2).
14.  eFlow104NB Moto Alarm Dimbura (Fig. 2c, p. 6): Kugonesa Fire Alarm Disconnect set DIP switch [Shutdown] kuenda ON chinzvimbo. Kuti udzime Fire Alarm Dimbura seta DIP switch [Shutdown] kuenda ku OFF chinzvimbo.
15. Kuiswa kwe tamper switch: Mount UL Yakanyorwa tamper switch (Altronix modhi TS112 kana yakaenzana) pamusoro peiyo yakavharirwa. Svetera iyo tamper switch bracket kumucheto kweiyo yakavharirwa inenge 2" kubva kurudyi (Fig. 4a, pg. 8). Batanidza tamper chinja wiring kune Access Control Panel yekupinda kana yakakodzera UL Yakanyorwa yekurekodha mudziyo. Kuti uvhure mucherechedzo wearamu vhura gonhi renzvimbo yakavharirwa.

Wiring:
Shandisa 18 AWG kana yakakura kune ese akaderera voltage power connections.
Cherechedza: Chengetedza kuchengetedza magetsi-ane mashoma maseketi akaparadzana kubva kune asina simba-akaganhurirwa wiring (120VAC, Bhatiri).
Maintenance:
Yuniti inofanirwa kuyedzwa kanenge kamwe pagore kuti iite basa rakakodzera sezvinotevera:
Kubuditsa Voltage Muedzo: Pasi pemamiriro akajairwa ekuremerwa, iyo DC inobuda voltage inofanirwa kuongororwa kuti ine voltage level eFlow104NB: 24VDC nominal rated @ 10A max.
Battery Test: Mumamiriro ezvinhu akajairwa tarisa kuti bhatiri razara chaji, tarisa yakataurwa voltage (24VDC @ 26.4) zvese pabhatiri terminal uye pabhodhi zviteshi zvakatemwa [- BAT +] kuona kuti hapana kutyora mutambo dzekubatanidza bhatiri.
Cherechedza: Maximum kuchaja ikozvino pasi pezvinobudiswa ndeye 1.54A.
Cherechedza: Hupenyu hwebhatiri hunotarisirwa makore mashanu, zvisinei zvinokurudzirwa kushandura mabhatiri mumakore mana kana pasi kana zvichidikanwa.
LED Diagnostics:
eFlow104NB Power Supply/Charger

Tsvuku (DC)	Green (AC/AC1)	Power Supply Status
ON	ON	Yakajairika mamiriro ekushanda.
ON	DZIMA	Kurasika kweAC. Batiri rekumira riri kupa simba.
DZIMA	ON	Hapana DC inobuda.
DZIMA	DZIMA	Kurasika kweAC. Radzimwa kana kushaya bhatiri rakamira. Hapana DC inobuda.

LINQ8ACM uye LINQ8ACMCB Networked Access Power Controller

LED	ON	DZIMA
LED 1- LED 8 (Dzvuku)	Output relay(s) de-energized.	Output relay(s) simba.
FACP	FACP inopinza yakakonzeresa (alarm mamiriro).	FACP yakajairika (isina-alarm mamiriro).
Green Output 1-8	12VDC	–
Red Output 1-8	24VDC	–
AC	AC Kukundikana	AC Normal
BAT	Bhatiri Yakundikana	Battery Normal

Dambudziko/Nguva Yakaganhurirwa Yambiro yeMabhatiri Akamira:
Kuti utevedzere ULC S318-96, iyo Time Limited Yambiro dunhu rinofanirwa kunge rakabatana kune yemuno kana kure kure neAmber kana Red LED kuratidza DC Dambudziko (yakaderera bhatiri, kurasikirwa kwebhatiri kana 95% yebhatiri rakamira rave. depleted). Batanidza dunhu kune Batt Fail relay mameseji kune yakakodzera kupinza yeUL Yakanyorwa Burglar Alarm kana Access Control Panel. Mufananidzo unotevera unoratidza kutenderera kunodiwa pakuzivisa kwenzvimbo.

Terminal Identification:
eFlow104NB Power Supply/Charger

Terminal/Legend		Tsanangudzo
A	– PWR1 +	Fekitari yakabatana ne eFlow104NB.
B	– PWR2 +	Optional yechipiri DC magetsi ekuisa.
C	Kubuditsa LED	Individual output voltage LEDs. 12VDC (Green) kana 24VDC (Red).
D	Output Jumper	Individual output voltage Sarudzo jumper (fekitari yakasarudzwa ye24VDC yakabuda).
E	COM -	Common Negative [-] plug yezvibatanidza spade.
F	Kubuda 1 kuburikidza Kubuda 8 Kwete, C, NC, COM	Zvisere (8) zvinosarudzwa zvakazvimiririra zvinodzorwa zvinobuda [Fail-Safe (NC) kana Fail-Secure (NO)].
G	-F, +F	FACP Signaling Circuit Input zviteshi. Kirasi 2 simba-shoma.
H	-R, + R	FACP Signaling Circuit Return terminals. Kirasi 2 simba-shoma.
I	GND, EOL	EOL Inotariswa FACP Input zviteshi zve polarity reversal FACP basa. Kirasi 2 simba-shoma.
J	GND, RST	FACP interface yatching kana kusa-latching. HAPANA yakaoma kuisa. Kirasi 2 simba-shoma. Kupfupikiswa kune isiri-latching FACP interface kana Latch FACP reset.
K	C, NC	FACP Dry NC yakabuda yakarongwa 1A/28VDC @ 0.6 Power Factor. Kirasi 2 simba-shoma. Iine EOL JMP yakasimba, ichapa 10k kuramba mune yakajairika mamiriro.
L	+ PS1 -	Fekitari yakabatana ne [+ BAT -] zviteshi zve eFlow104NB magetsi.
M	+ BAT -	Kubatanidza kumabhatiri akamira.
N	+ PS2 -	Kubatanidza ku [+ BAT -] zviteshi zvesarudzo yechipiri DC magetsi.
O	+ BAT -	Kubatanidza kune stand-by bhatiri (ies) yesarudzo yechipiri DC magetsi emagetsi.
P	+ INP1 - kuburikidza + INP8 -	Masere (8) anodzorwa akazvimirira Kazhinji Kuvhurika (NO), Kazhinji Kuvharwa (NC), Vhura Muunganidzi Sink kana Wet Input Triggers.
Q	Tamper	Tamper Chinja Input.
R	AC / NC, C	Batanidza midziyo yekuzivisa yekuzivisa yakakodzera kune materminal kuti utaure kuti AC yakundikana.
S	BAT / NC, C	Batanidza midziyo yekuzivisa yekuzivisa yakakodzera kune materminal kuti utaure kutadza kwebhatiri.
T		Yakachengeterwa kushandiswa mune ramangwana.
U	8-Pin Chinongedzo	Zvekubatanidza kuVR6 kana Tango1B.
V	USB	Laptop yekubatanidza inogonesa LINQ8ACM (CB) yekutanga kuseta uye hurongwa.
W	RJ45	Ethernet: LAN kana laptop yekubatanidza inogonesa LINQ8ACM(CB) kuronga uye mamiriro ekutarisa.
X	PWR1+, PWR2+	Positive [+] mapulagi ezvikoniko zvemapadza.
Y	2-Pin Chinongedzo	Kubatanidza ku[AC Kukundikana] materminals pamagetsi.
Z	EOL Jumper	Inobata 10 k Ohm End-of-Line resistor.

Terminal Identification:
LINQ8ACM uye LINQ8ACMCB Networked Access Power Controller

Terminal Legend	Basa/ Tsanangudzo
L, N	Batanidza 120VAC 60Hz kune aya materminal: L kusvika kupisa, N kuenda kune kwaakarerekera (asina simba-ane mashoma) (Mufananidzo 2a, peji 6).
– DC +	24VDC nominal @ 10A inoenderera kuburitsa (isina simba-inogumira kubuda) (Mufananidzo 2h, peji 6).
Trigger EOL Inotariswa	Fire Alarm Interface inokonzeresa kupinza kubva kupfupi kana FACP. Trigger inputs inogona kuvhurika kazhinji, kazhinji yakavharwa kubva kuFACP inobuda dunhu (simba-shoma yekupinda) (Mufananidzo 2d, peji 6).
KWETE, GND RESET	FACP interface latching kana isiri-latching (simba-shoma) (Mufananidzo 2e, peji 6).
+ AUX -	Yekubatsira Kirasi 2 simba-rinogumira kuburitsa yakayerwa @ 1A (isina switched) (Mufananidzo 2f, peji 6).
AC Fail NC, C, NO	Inoratidza kurasikirwa kwesimba reAC, semuenzaniso batanidza kune chinonzwika mudziyo kana alarm panel. Relay kazhinji inopihwa simba kana AC simba riripo. Kubata chiyero 1A @ 30VDC (simba-shoma) (Mufananidzo 2b, peji 6).
Bat Fail NC, C, NO	Inoratidza kuderera kwebhatiri mamiriro, semuenzaniso batanidza kune alarm panel. Relay kazhinji inopihwa simba kana DC simba iripo. Kubata chiyero 1A @ 30VDC. Bhatiri rakabviswa rinoshumwa mukati memaminitsi mashanu. Kubatanidza bhatiri kunotaurwa mukati meminiti 1 (simba-shoma) (Mufananidzo 2b, peji 6).
– BAT +	Fekitari yakabatana neLINQ8ACM(CB). Maximum charge ikozvino 1.54A (isina simba-inogumira) (Mufananidzo 2g, peji 6).

DC Output kune zvishandiso
                                                                          (eFlow104NKA8QM - isina simba-inogumira, eFlow104NKA8DQM - simba-shoma)

Optional Rechargeable Stand-by Battery yeUL294 Applications Cherechedza: 12V mabhatiri anodiwa pakuisa ULC-S319.

Optional Rechargeable Stand-by Battery yeUL294 Applications Cherechedza: 12V mabhatiri anodiwa pakuisa ULC-S319.

CHENJERERO: Shandisa mabhatiri maviri (2) 12VDC akamira-ne. Chengetedza magetsi-akaganhurirwa wiring akaparadzana neasina simba-shoma. Shandisa zvishoma 0.25” nzvimbo. 12AH Rechargeable mabhatiri ndiwo mabhatiri makuru anogona kukwana mune ino yakavharwa. A UL yakanyorwa ekunze kwebhatiri yakavharirwa inofanira kushandiswa kana uchishandisa 40AH kana 65AH mabhatiri.

Network Setup:
Ndokumbira uve shuwa yekushanyira altronix.com kune yazvino firmware uye yekuisa mirayiridzo.

Network Programming Via Altronix Dashboard USB Connection:
Iyo USB yekubatanidza paLINQ8ACM(CB) inoshandiswa kuseta network paramita. Kana yakabatana nePC kuburikidza ne USB tambo iyo LINQ8ACM(CB) ichagamuchira simba kubva ku USB port ichibvumira network programming yeLINQ8ACM(CB) isati yabatanidzwa kune magetsi.

1. Isa software inopihwa neLINQ8ACM(CB) paPC iri kushandiswa kurongwa. CHERECHEDZA: Iyi software inofanirwa kuiswa pamakomputa ese achawana mukana weLINQ8ACM(CB).
2. Batanidza tambo ye USB yakapihwa pachiteshi che USB paLINQ8ACM(CB) uye komputa.
3. Dzvanya kaviri pane Dashboard icon padesktop yekombuta uye wovhura Dashboard. Pinda Zita reMushandisi: admin uye Password: admin kuti uwane dashboard.
4. Dzvanya pane bhatani rakanyorwa USB Network Setup muruwoko rwepamusoro pedhibhodhi. Izvi zvichavhura iyo USB Network Setup skrini. Muchidzitiro ichi MAC Kero yeLINQ8ACM(CB) module ichawanikwa pamwe neNetwork Settings.

Network Settings:
Munzvimbo yeIP Kero Method sarudza nzira iyo iyo IP Kero yeLINQ8ACM(CB) ichawanikwa: "STATIC" kana "DHCP", wotevera matanho akakodzera (bata network maneja kuti uone kuti ndeipi nzira ichashandiswa) .
Static:

1. IP Kero: Isa iyo IP kero yakapihwa LINQ8ACM(CB) nenetiweki maneja.
2. Subnet Mask: Pinda iyo Subnet yetiweki.
3. Gedhi: Pinda iyo TCP/IP gedhi retiweki yekupinda nzvimbo (router) iri kushandiswa.
   CHERECHEDZA: Kugadziriswa kwegedhi kunodiwa kuti ugamuchire maemail kubva kumushini.
4. Inbound Port (HTTP): Isa nhamba yechiteshi yakapihwa LINQ8ACM(CB) module nenetiweki maneja kuti ubvumire kuwana kure uye kutarisa.
5. Dzvanya bhatani rakanzi Submit Network Settings. Bhokisi rebhokisi rinoratidza "Zvitsva zvetiweki zvigadziriso zvichatanga mushure mekunge sevha yatangwazve". Dzvanya OK.

DHCP:

1. Mushure mekusarudza DHCP muIP Kero Method tinya bhatani rakanzi Submit Network Settings. Bhokisi rebhokisi rinoratidza "Zvitsva zvetiweki zvigadziriso zvichatanga mushure mekunge sevha yatangwazve". Dzvanya OK. Tevere, tinya pane bhatani rakanyorwa Reboot Server. Mushure mekutangazve iyo LINQ8ACM(CB) ichaiswa muDHCP modhi. Iyo IP kero ichapihwa neiyo router kana iyo LINQ8ACM(CB) yakabatana kune network. Zvinokurudzirwa kuve neiyo IP Kero yakachengeterwa kuti ive nechokwadi chekuenderera mberi nekuwana (ona network administrator).
2. Subnet Mask: Paunenge uchishanda muDHCP, router inogovera iyo subnet mask kukosha.
3. Gedhi: Pinda iyo TCP/IP gedhi retiweki yekupinda nzvimbo (router) iri kushandiswa.
4. HTTP Port: Isa iyo HTTP port nhamba yakapihwa LINQ8ACM(CB) module nenetiweki maneja kuti ubvumire kuwana kure uye kutarisa. Iyo yekuseta yemukati yemukati ndeye 80. HTTP haina encrypted uye haina kuchengetedzwa. Kunyangwe HTTP ichigona kushandiswa kuwana kure kure, inokurudzirwa kuti ishandiswe neLAN kubatana.

Chengetedza Network Setup (HTTPS):
Kuti ugadzire HTTPS yeYakachengeteka Network Connection, Chitupa Chinoshanda uye Kiyi zvinofanirwa kushandiswa. Zvitupa neKiyi zvinofanirwa kunge zviri muchimiro che“.PEM”. Self-Certification inofanirwa kungoshandiswa pakuedza zvinangwa chete sezvo pasina humbowo chaihwo huri kuitwa. MuSelf-Certified mode, iyo yekubatanidza icharamba ichitaura kuti haina kuchengetedzeka.

Maitiro ekukwirisa Chitupa uye Kiyi yekuseta HTTPS:

1. Vhura Tab Yakanyorwa Chengetedzo.
2. Sarudza Tab Yakanyorwa Email/SSL.
3. Skira pasi pasi peSSL Settings.
4. Dzvanya Sarudza Chitupa.
5. Bhurawuza uye sarudza Chitupa chakakodzera chekuisa kubva kune server.
6. Dzvanya Sarudza Kiyi.
7. Bhurawuza uye sarudza kiyi inoshanda yekuisa kubva kuseva.
8. Dzvanya Tumira Files.

Kana Chitupa neKiyi zvaiswa zvinobudirira unogona kuenderera mberi nekumisikidza HTTPS muNetwork Settings.

• HTTPS Chiteshi: Isa nhamba yechiteshi cheHTTPS yakapihwa LINQ8ACM(CB) module nenetiweki maneja kuti ubvumidze kupinda nekutarisisa kure. Iyo default inbound port setting ndeye 443. Ive yakavharidzirwa uye yakachengeteka zvakanyanya, HTTPS inokurudzirwa zvikuru kuti isvike kure.
• Dzvanya bhatani rakanzi Submit Network Settings. Bhokisi rebhokisi rinoratidza "Zvitsva zvetiweki zvigadziriso zvichatanga mushure mekunge sevha yatangwazve". Dzvanya OK.

Kuti uwane iyo LINQ8ACM(CB) kuburikidza neAltronix Dashboard tarisa kune Dashboard Kuiswa uye Chirongwa Chinyorwa chiri pane inopihwa flash drive.
Programming Via Browser:
Kana usingashandisi iyo Altronix Dashboard USB yekubatanidza kune yekutanga Network setup, iyo LINQ8ACM(CB) inoda kubatana kune chero DC magetsi emagetsi (ies) kana eFlow magetsi ekupa (ies) inotariswa isati yaitwa chirongwa. Tarisa kuLINQ8ACM(CB)'s Mirairo yekuisa iri papeji 3 yebhuku rino.

Factory Default Settings:

• IP Kero: 192.168.168.168
• Zita remushandisi: admin
• Password: admin

1. Gadzirisa iyo IP kero yelaptop kuti ishandiswe kuronga kune imwecheteyo network IP kero seLINQ8ACM(CB), kureva 192.168.168.200 (default address yeLINQ8ACM(CB) is 192.168.168.168).
2. Batanidza imwe magumo etiweki tambo kune network jack paLINQ8ACM(CB) uye imwe kune network yekubatanidza yelaptop.
3. Vhura bhurawuza pakombuta uye isa "192.168.168.168" mubhari yekero. Bhokisi rebhokisi Kusimbisa Kunodiwa ichaonekwa ichikumbira zvese zita remushandisi uye password.
   Isa izvo zvakatarwa pano. Baya bhatani rakanzi Log In.
4. Iyo peji peji yeLINQ8ACM(CB) ichaonekwa. Peji ino inoratidza mamiriro enguva chaiyo uye hutano hwemagetsi ega ega akabatana neLINQ8ACM(CB).Kuisa mitsva inetiweki paramita, enda kuNetwork Setup pasi peLINQ8ACM(CB) Configuration chikamu chebhuku rino.

LINQ8ACM(CB) Kugadzirisa:
Kuisa Saiti ID, Nguva uye Zuva:
Saiti ID inoshandiswa kuona nzvimbo uye tsananguro yemuchina wakatariswa.

1. Dzvanya paStatus tab kuti uwane iyo peji peji.
2. Dzvanya paSaiti ID kumusoro kuruboshwe, bhokisi rebhokisi rinovhura.
3. Pinda nzvimbo uye tsananguro yeinotariswa mudziyo.
4. Dzvanya tumira.

Nguva uye Zuva zvinofanirwa kuiswa kuti zvinyatso stamp iyo system log uye email chenjedzo.

1. Dzvanya paStatus tab kuti uwane iyo peji peji.
2. Dzvanya nguva uye zuva kumusoro kuruboshwe, bhokisi rebhokisi rinovhura.
3. Dzvanya pakanzi “SYNC DATE AND TIME”.

• Hardware Setup:
  Dzvanya pane Settings tab kuti uvhure Hardware Setup skrini. Input / Output Setup:
  1. Dzvanya pane INPUT / OUTPUT tebhu kumusoro kwechidzitiro.
  2. Output ID: Isa zita rinotsanangura remudziyo wakabatana kune yakabatana inobuda.
  3. Kudzora Kubuda: uchishandisa iyo yekudonhedza menyu sarudza kana iyo inobuda ichadzorwa kuburikidza nekupinda yekudzora yekupinda kune inokonzeresa terminals kana software inodzorwa.
     1. Kuisa Kudzora: zvinobuda zvinodzorwa kuburikidza neiyo Trigger Input,
     2. Manual Control: zvinobuda zvinodzorwa nemaoko kuburikidza neLINQ software. Zvinobuda zvichadzorwa kuburikidza nesoftware-yakatangwa.
  4. Zvakakonzerwa: Kutarisa kana kusatarisisa bhokisi rakabatana rinobuda kunochinja chinobuda kana bhatani reTumira radzvanywa. Zvakawanda zvinobuda zvinogona kuchinjwa panguva imwe chete.
     CHERECHEDZA: Iri basa kana richishandiswa muManual Control chete.
  5. Zvinopinza iyo inopinza inogona kurongwa kuti idzore kubuda kumwe chete kana kuwanda.
     1. Single output control: uchishandisa iyo yekudonhedza menyu yeinoenderana inobuda (kureva Input1 g Output1), sarudza mhando yekupinda yekudzora yekupinda NO Kazhinji yakavhurika kana NC inowanzovharwa.
     2.  Multiple output control: uchishandisa iyo yekudhonza-pasi menyu yezvese zvinobuda kuti zvidzorerwe (kureva Input1 g Output1 g Output4 g Output7) sarudza mhando yekupinda yekudzora yekupinda NO Inowanzo kuvhurika kana NC inowanzovharwa. Zvese zvakasarudzwa zvinobuda zvichachinja mamiriro kana iyo yekupinza yatanga.
  6. Mhando yeKubuda: uchishandisa iyo yekudhonza-pasi tebhu sarudza kuti chinobuda chichashandiswa sei: Fail-Safe (midziyo inoda kukiya), Yakundikana-Chengetedzwa (mudziyo unoda simba rekuburitsa), kana Wekubatsira (midziyo inoda kugara isingachinji simba).
  7. FACP: uchishandisa iyo yekudonhedza-pasi tebhu sarudza kuti iyo inobuda ichaita sei kana aramu yemoto ikabviswa: Isingashande (iyo inobuda icharamba ichishanda), isiri-latching (iyo inobuda ichaburitsa kana FACP yagadziriswazve), Latching (zvinobuda zvinoramba zvichikonzereswa. kana FACP ikagadziridzwa uye inoramba ichikonzeresa kusvika yaburitswa nemaoko kuburikidza nekuisa kune reset terminals).
  8. Battery Backup: sarudza kana izvo zvinobuda zvichatsigirwa kana simba rakundikana. Bvisa bhokisi rakabatana kuti uvhare bhatiri kumashure kune izvo zvinobuda.
  9. Pamusoro/Pasi Pazvino: Pinda ese ari maviri ePamusoro nePasi ezvino miganho kune yakabatana inobuda. Kana imwe yeiyi miganho yakapfuura meseji yekuzivisa uye/kana email ziviso ichagadzirwa.
  10. Over/Under Voltage: Pinda zvese zviri zviviri High uye Low voltage miganhu yezvakabatana zvinobuda. Kana imwe yeiyi miganho yakapfuura meseji yekuzivisa uye/kana email ziviso ichagadzirwa.
  11. Baya bhatani rakanyorwa kuti Tumira kuti uchengetedze marongero.

Tembiricha Settings:

1. Dzvanya pane Temperature tebhu kumusoro kwechidzitiro.
2. Pinda tembiricha yepamusoro muCelsius.
3. Baya bhatani rakanyorwa kuti Tumira kuti uchengetedze marongero.

Battery Service Date (ma)
Kana mabhatiri asiri kushandiswa bvisa bhokisi riri pazasi Present kudzima bhatiri yekutarisa.

1. Dzvanya paBatteries tebhu kumusoro kwechidzitiro.
2. Isa zuva rakaiswa mabhatiri pasi peKuiswa Date kune yega yega yakabatana magetsi.
3. Isa zuva rebasa rebhatiri pasi peSevhisi Date kune yega yega yakabatana magetsi.
   CHERECHEDZA: Mabhatiri anofanira kuongororwa kamwe chete pagore. Kunyangwe kuburikidza nehupenyu hunotarisirwa hwebhatiri makore mashanu (5) zvinokurudzirwa kutsiva mabhatiri makore mana (4) ega ega.
4. Baya bhatani rakanyorwa kuti Tumira kuti uchengetedze marongero

Power Supply Settings:
Kana imwe chete (1) magetsi ari kushandiswa bvisa bhokisi riri pasi pePresent padivi pesimba risingashandiswe rekudzima kutarisa.

1. Dzvanya pane Power Supplies tebhu kumusoro kwechidzitiro.
2. Over/Under Voltage: Pinda zvese zviri zviviri zvePamusoro nePazasi voltage miganhu yeinobatanidzwa inopinza. Kana imwe yeiyi miganho yakapfuura meseji yekuzivisa uye/kana email ziviso ichagadzirwa.
3. Pamusoro / Pasi Pazvino: Pinda ese ari maviri ePamusoro uye Akaderera azvino miganhu yeinobatanidzwa yekuisa. Kana imwe yeiyi miganho yakapfuura meseji yekuzivisa uye/kana email ziviso ichagadzirwa.
4. Baya bhatani rakanyorwa kuti Tumira kuti uchengetedze marongero

Kugadziriswa Kwezvino Kubuda:
Panguva yekuseta kwekutanga zvese zvinobuda zvinoda kuenzaniswa kuti zvive nechokwadi chekuverenga kwazvino.

1. Dzvanya paCalibration tebhu kumusoro kwechidzitiro.
2. Nemitoro yese yadimburwa tinya pane tab yakanyorwa Calibrate All Zero Offset Currents kuseta zvese zvinobuda kusvika zero.
3. Kubatanidza chinobuda chimwe nechimwe panguva, kuyera dhirowa iripo uye isa kukosha uku kweichi chinobuda pasi peChaiyo.
4. Dzvanya pane bhatani rakanyorwa Calibrate Gain kuchengetedza marongero.
5. Dzokorora nhanho 3 & 4 kune zvese zvasara zvinobuda.

Kana uchitsiva kana kuwedzera mudziyo mutsva chinobuda chinoda kudzokororwa.

1. Dzvanya paCalibration tebhu kumusoro kwechidzitiro.
2. Nekuremerwa kwakadzimwa kubva pane zvakabuda, tinya pane tab yakanyorwa Calibrate Offset kuti iyo inobuda igadzirise yazvino kusvika zero.
3. Batanidza zvakabuda, yera iyo yazvino dhirowa uye isa iyi kukosha pasi peChaiyo.
4. Dzvanya pane bhatani rakanyorwa Calibrate Gain kuchengetedza marongero.
5. Dzokorora nhanho 3 & 4 kune zvese zvasara zvinobuda.

B. Timer Setup:
Dzvanya paTimer tab kuti uwane iyo nguva yekuseta skrini.

1. Dzvanya pane Wedzera New Timer bar.
2. Timer Label: Isa zita rinotsanangura renguva basa.
3. Nguva Yekutanga Zuva: Isa zuva richatanga basa renguva (kureva 10/09/2019).
4. Nguva yenguva: Uchishandisa iyo yekudonhedza menyu sarudza nguva iyo nguva ichashanda.
5. Nguva Yekutanga Nguva: isa iyo nguva ichatanga chiitiko chenguva.
6. Zviito zveTimer: Sarudza basa kune yega yega inobuda ichaitika panguva yechiitiko chenguva.
7. Baya bhatani rakanyorwa kuti Tumira kuti uchengetedze marongero. Kuti uwedzere zvimwe zviitiko zvenguva, dzokorora nhanho 1-7.

C. Network Setup:

Static:

1. IP Kero: Isa iyo IP kero yakapihwa LINQ8ACM(CB) nenetiweki maneja.
2. Subnet Mask: Pinda iyo Subnet yetiweki.
3. Gedhi: Pinda iyo TCP / IP gedhi retiweki yekupinda nzvimbo (router) iri kushandiswa. Kugadziriswa kwegedhi kunodiwa kuti ugamuchire maemail kubva kumushini.
4. HTTP Port: Isa iyo HTTP port nhamba yakapihwa LINQ8ACM(CB) module nenetiweki maneja kuti ubvumire kuwana kure uye kutarisa. Iyo yekuseta yemukati yemukati ndeye 80. HTTP haina encrypted uye haina kuchengetedzwa. Kunyangwe HTTP ichigona kushandiswa kuwana kure kure, inokurudzirwa kuti ishandiswe neLAN kubatana.
5. HTTPS Chiteshi: Isa nhamba yechiteshi cheHTTPS yakapihwa LINQ8ACM(CB) module nenetiweki maneja kuti ubvumidze kupinda nekutarisisa kure. Iyo default inbound port setting ndeye 443. Ive yakavharidzirwa uye yakachengeteka zvakanyanya, HTTPS inokurudzirwa zvikuru kuti isvike kure. Kana HTTPS iri kushandiswa zvinokurudzirwa kuti usatarise bhokisi riri padyo neHTTP kuti udzime kushandiswa kwayo.
6. Kana minda yese yapera baya bhatani rakanzi Submit.
7. Dzvanya bhatani rakanyorwa Reboot kuti uchengetedze marongero.

DHCP:

1. Mushure mekusarudza DHCP mundima yeMethod tinya bhatani rakanzi Tumira. Tevere, tinya pane bhatani rakanyorwa Reboot kuchengetedza marongero. Mushure mekutangazve iyo LINQ8ACM(CB) ichaiswa muDHCP modhi. Iyo IP kero ichapihwa neiyo router kana iyo LINQ8ACM(CB) yakabatana kune network. Ona network maneja weDHCP paramita.
2. Subnet Mask: Kana uchishanda muDHCP iyo router inogovera iyo subnet mask kukosha.
3. Gedhi: TCP/IP gedhi retiweki yekupinda nzvimbo (router) iri kushandiswa icharatidzwa.eFlow104NKA8DQM Kuisa Guide
4. d. HTTP Port: Isa iyo HTTP port nhamba yakapihwa kuLinq8ACM module nenetiweki maneja kuti ubvumire kuwana kure uye kutarisa. Iyo yekuseta yemukati yemukati ndeye 80. HTTP haina encrypted uye haina kuchengetedzwa. Kunyangwe HTTP ichigona kushandiswa kuwana kure inokurudzirwa kuti ishandiswe neLAN kubatana.
5. HTTPS Chiteshi: Isa nhamba yechiteshi cheHTTPS yakapihwa LINQ8ACM(CB) module nenetiweki maneja kuti ubvumidze kupinda nekutarisisa kure. Iyo default inbound port setting ndeye 443. Ive yakavharidzirwa uye yakachengeteka zvakanyanya, HTTPS inokurudzirwa zvikuru kuti isvike kure.
6. Kana mamwe minda ese apera tinya bhatani rakanzi Tumira.
7. Dzvanya bhatani rakanyorwa Reboot kuchengetedza marongero.

D. Cloud Settings:
LINQ8ACM(CB)'s cloud support yakavharwa nekusarudzika. Kana rutsigiro rwegore rwagoneswa, LINQ8ACM(CB) inoshandisa tsigiro yegore kupa zviziviso zveemail uye nekupa zvigadziriso kana zviripo. Tarisa bhokisi riri padyo neGonesa kubvumidza chiitiko email zviziviso kuburikidza nerutsigiro rwegore. Advanced Settings: Cloud network traffic inogona kuendeswa kune maseva emunharaunda kana ichidikanwa.

1. Pinda yemunharaunda cloud server IP kero muIP Kero ndima.
2. Pinda pro ID mumunda wePort.
3. Tarisa kubhokisi riri pedyo neKugonesa.
4. Baya bhatani rakanyorwa kuti Tumira kuti uchengetedze marongero.

Paunenge uchishandisa yemunharaunda inogona sevha uye SSL/TLS iri kushanda, chitupa chitsva chinoda kuiswa.

Certificate Upload:

1. Dzvanya pane Sitifiketi tebhu kumusoro kwechidzitiro.
2. Dzvanya pakanzi Sarudza Chitupa File uye tsvaga chitupa chitsva.
3. Isa chitupa.
4. Baya bhatani rakanyorwa kuti Submit kuti uchengetedze file.

E. Email Setup:

1. Dzvanya pane Email tebhu kuti uwane iyo email marongero skrini.
2. Dzvanya pane Inobuda tab kuti uwane inobuda Email Settings skrini.
3. Pinda anosvika mashanu (5) kero dzeemail dzinobuda dzinogamuchira email chenjedzo.
4. Kana maemail ese aiswa tinya bhatani reTumira kuti uchengetedze marongero.

Email Test:

1. Dzvanya pane Test tab kuti uwane iyo Email Test skrini.
2. Uchishandisa menyu yekudhonza sarudza meseji yekuyedza inotumirwa.
3. Dzvanya bhatani rekutumira kuti utumire meseji yekuyedza.

F. Network Security Settings:

1. Dzvanya pane Chengetedzo tebhu kuti uwane iyo Chengetedzo Settings skrini.
2. Dzvanya iyo tabhu yakakodzera kumusoro kwechidzitiro kuti minda igadziriswe.

Mitemo
Sarudza yambiro yekuchengetedza icharatidzwa paunenge uchipinda muhurongwa nekutarisa kuratidza uye kusatarisa kuti usaratidze meseji yambiro.

Kugadzika Setifiketi Yekuzvisainira:
Kugadzira yega-yakasaina SSL Sitifiketi uye Kiyi:

1. Nyika: Mabhii maviri kodhi inomiririra nyika iyo sangano riripo.
2. Nzvimbo: Guta iro sangano riripo.
3. Sangano: Zita repamutemo resangano. Izvi hazvifanirwe kupfupikiswa, uye zvinofanirwa kusanganisira zvirevo zvakaita seInc., Corp, kana LLC.
4. Unit Name: Zita remudziyo.
5. Common Name: Domain zita kana IP kero ye server. Izvi zvinowanzopihwa netiweki maneja.
6. Email Kero: email kero inoshandiswa kubata sangano.
7. Mushure mese ndima yapedzwa tinya bhatani rakanzi Tumira kuti uchengetedze marongero

CHERECHEDZA: Chitupa cheSSL chakasaina pachacho chinogadzirwa neruzivo rwunopihwa muminda ye "SSL Sitifiketi Zvirongwa". Chitupa chichashanda kwemazuva 500, uye nguva stamped nemasetirwo enguva aripo paLINQ8ACM(CB) module. Zuva uye nguva zvinofanirwa kuwiriraniswa nekombuta inotambira usati wagadzira chitupa cheSSL.

Certificate Upload:
Kuisa yakavanzika Chitupa uye Kiyi.

1. Pasi peSitifiketi kurodha tinya pane Sarudza Chitupa File.
2. Tsvaga chitupa chitsva file.
3. Isa chitupa file.
4. Pazasi Key upload tinya pane Sarudza Kiyi File.
5. Tsvaga chitupa chitsva file.
6. Isa Kiyi file.
7. Baya bhatani rakanyorwa kuti Submit file chengetedza marongero

Zvirongwa Zvevashandisi:
Pane akati wandei anorongwa mushandisi mwero anowanikwa.
Administrator: Inokwanisa kuwana mabasa ese.
Status/Setup: Iine on/off control uye inogona kupa zita remagetsi. Network: Iyi marongero ndeye IT administrator.
Maintenance: Iine mukana wekugadzirisa Alerts uye timer control.
Kugadzirisa Vashandisi:

1. Dzvanya pane Users tab.
2. Dzvanya pa Wedzera bhatani remushandisi mutsva iyo New User Form ichavhura.
3. Isa zita remushandisi.
4. Isa password yakasarudzika pasi peNew Password.
5. Pindazve password pasi Confirm Password.
6. Sarudza rudzi rwemushandisi uye kodzero dzemushandisi: Verenga / Nyora (unogona kuchinja) kana Verenga Chete (view chete). Mushandisi anogona kuseta semaneja nekudzvanya pa MAKE ADMIN pamusoro peTumira bhatani.
7. Dzvanya pakanzi Tumira kuchengetedza marongero.
8. Dzokorora zviri pamusoro kuti uwedzere vamwe vashandisi.

Alerts uye Report Kunonoka Settings:
Nyevero inogona kugoneswa kutumira chiziviso chekuti chiitiko chaitika kana kuremadzwa kuti usatarise chiitiko uye kusatumira chiziviso. Kuti udzime chiitiko, bvisa bhokisi reKugonesa bhokisi riri padyo nechiitiko chichadzimwa. Kuti uite zvakare chiitiko tarisa bhokisi riri padyo nechiitiko.
Zviitiko zvinogona kuiswa kuti zvinonoke zvisati zvaziviswa.
Kuseta kunonoka kwemushumo pinda nguva yekunonoka mukoramu pasi peDelay Report yechiitiko chakabatana. Nguva yekunonoka inoiswa mumasekonzi. Zviitiko zvese zvakagadzirirwa kwemasekonzi maviri. Kana minda yese yapera tinya bhatani rakanzi Tumira kuti uchengetedze zviitiko zvechiitiko. Dzokorora kuti zvimwe zviitiko zvese zvigadziriswe.

Hook-Up Diagrams:

Mufananidzo 6 - Daisy-chaining imwe kana kupfuura LINQ8ACM (CB) zvikamu. EOL Jumper [EOL JMP] inofanira kuiswa munzvimbo yeEOL. Non-Latching.

Mufananidzo 7 - Daisy-chaining imwe kana kupfuura LINQ8ACM (CB) zvikamu. EOL Jumper [EOL JMP] inofanira kuiswa munzvimbo yeEOL. Latching Single Reset.

Fig. 8 – Daisy chaining one or more LINQ8ACM(CB) units. EOL Jumper [EOL JMP] inofanira kuiswa munzvimbo yeEOL. Latching Individual Reset.

Hook-Up Diagrams:

Fig. 9 - Polarity reversal input kubva ku FACP signaling circuit output (polarity inotaridzirwa mumamiriro e alarm). Non-Latching.

Fig. 10 - Polarity reversal input kubva ku FACP inoisa chiratidzo chedunhu kubuda (polarity inotaridzirwa mumamiriro e alarm). Latching.

Fig. 11 - Kazhinji Yakavharwa trigger input (Non-Latching).

Fig. 12 - Kazhinji Yakavharwa trigger input(Latching).

Fig. 13 - Kazhinji Open trigger input (Non-Latching).

Fig. 14 - Kazhinji Open trigger input (Latching).

Enclosure Dimensions (BC400):
15.5" x 12" x 4.5" (393.7mm x 304.8mm x 114.3mm)

Altronix haina mhosva kune chero zvikanganiso zve typographical. 140 58th Street, Brooklyn, New York 11220 USA | foni: 718-567-8181 | fax: 718-567-9056websaiti: www.altronix.com | e-mail: info@altronix.com | Hupenyu Hwarandi IIeeFlow104NKA8DQM G30U

Zvinyorwa / Zvishandiso

Altronix eFlow104NKA8QM Series Networkable Dual Output Access Power Controllers [pdf] Installation Guide eFlow104NKA8QM Series Networkable Dual Output Access Power Controllers, eFlow104NKA8QM Series, Networkable Dual Output Access Power Controllers, Power Controllers.

References

• User Manual