For More Shining Ideas
EinScan Pro HD
Multifunctional Handheld 3D Scanner
Quick Start Guide
Getting Started with EinScan Pro HD
Preparation
Device List
Standard Pack
Note:
- Plug in dongle before opening Solid Edge software
- Find the use of phone screen mount in Support-Help at www.einscan.com
Industrial Pack (optional)
Color Pack (optional)
*Please only use water to clean the calibration board, avoid touching any corrosive liquid.
Recommended
| OS | Win10, 64bit |
| Graphics Card | NVIDIA GTX/RTX series cards，higher or equal to GTX 1080 |
| Video Memory | >4G |
| Processor | I7-8700 |
| Memory | 64G |
| Interface | high-speed USB 3.0 |
Installation
Hardware Installation
- Standard Pack
STEP 01 Turn on the device and connect it to the computer through USB 3.0 port.
- Industrial Pack
STEP 01
Fasten the scanner tray onto the tripod and place the scanner on the tray.
STEP 02
Plug the USB cable into the USB port of the turntable and connect it to the computer. Connect the power cable to the turntable.
- Color Pack
STEP 01 Hold the device upright and remove the USB port cover. The cover is located near the logo on the right side of the device.
STEP 02 Insert the Color Pack and lock it with a rotary lever.
- Operation Environment
Avoid direct sunlight or too bright of light indoors.
Make sure the scanned object and table are stable. （For Fixed Scan）
Software Installation
Software Download
Download the software and user manual from support.shining3d.com or www.einscan.com/software-download
STEP 01 Run the installer
Double click software installation icon to install the software.
STEP 02 License Activation
After successful installation, when the device is correctly connected, double-click to open the software and activate the device. The format of activation is “online activation”. Make sure your computer is connected to the Internet.
Or do local activation and find the license in the USB drive.
Attention: If you install another device of different serial number, the software will automatically notify users to activate this device.
Calibration
STEP 01 Camera Calibration
Follow the instruction on the software to place the calibration board in 5 different positions. Hold the scanner vertically and cover the screen range.
STEP 02
STEP 03
STEP 04
STEP 05
White Balance Calibration
Only required for Color Pack Hold the scanner vertically to the back side of calibration board (white) and adjust the distance until you find the proper distance.
The first time installing the software , calibration is required by default. Calibration is also required for the following:
- Device Change
- After device enduring bumpy transportation
- After device accuracy decreases
- Device being uncalibrated for a long time, for example, 15 days.
- When using the Color Pack, the texture camera’s position has been changed.
Fixed Scan
Handheld HD Scan
Handheld Rapid Scan
Scanning Tips
Scan Mode Selection
Use Handheld Rapid Scan mode when:
A fast scanning experience is needed;
Objects with good geometry for feature alignment;
Objects are hard to move or too big to stay on turntable for scanning.
Use Handheld HD Scan mode when:
High accuracy and high resolution by handheld scanning is required;
Objects are hard to move or too big to stay on turntable for scanning.
Use Fixed Scan with Turntable mode when:
High accuracy and high resolution is required;
Objects’ footprint within 150mm which may not cover most coded targets on turntable;
Weight under 5kg;
Objects’ footprint above 150mm with rich geometry features can also work in Fixed Scan with Turntable mode through feature alignment.
Use Fixed Scan without Turntable mode when:
High accuracy and high resolution is required;
Objects is too big or heavy to work on turntable.
Summary
| Mode | Accuracy （mm） | Scan Efficiency | Resolution Point distance （mm） | Align Mode |
| Fixed Scan with Turntable |
Single Shot Accuracy 0.04  |
Single Scan < 0.5s |
0.24 |
Turntable Coded Targets, Feature, Markers, Manual |
| Fixed Scan without Turntable |
Single Shot Accuracy 0.04 |
Single Scan < 0.5s |
0.24 |
Feature, Markers, Manual |
| Handheld HD Scan |
Up to 0.045 +0.3 mm/m (markers alignment) |
10 fps 3,000,000 points/s |
0.2-3 |
Markers, Feature (with rich geometrical features on the surface), Hybrid(Markers and Feature) |
| Handheld Rapid Scan |
Up to 0.1 +0.3 mm/m (markers alignment)  |
30 fps 1,500,000 points/s |
0.25-3 |
Markers, Feature (with rich geometrical features on the surface), Hybrid(Markers and Feature) Texture (with rich texture) |
Difficult to Scan
- Transparent objects like glasses
- Shining or highly reflective objects like mirrors
Solution
- Spray with white powder
Not Recommended
- Moving objects or vibrating objects
- Lattice structure with many small deep holes
- Hairy objects like human hair and fur
Technical Support
Register at support.shining3d.com for support or contact through:
Email: einscan_support@shining3d.com
Skype: einscan_support
For more videos of the scanners, please follow our YouTube channel “ SHINING 3D” .
APAC Headquarters
SHINING 3D Tech. Co., Ltd.
Hangzhou, China
P: +86-571-82999050
Email: sales@shining3d.com
No. 1398, Xiangbin Road, Wenyan,
Xiaoshan,Hangzhou, Zhejiang, China, 311258
Americas Region
SHINING 3D Technology Inc.
San Francisco, United States
P: +1415-259-4787
Email: sales@shining3d.com
1740 César Chávez St. Unit D.
San Francisco, CA 94124
www.shining3d.com
EMEA Region
SHINING 3D Technology GmbH.
Stuttgart, Germany
P: +49-711-28444089
Email: sales@shining3d.com
Breitwiesenstraße 28, 70565,
Stuttgart, Germany
Documents / Resources
 |
SHINING 3D RN-113 Multifunctional Handheld 3D Scanner [pdf] User Guide RN-113 Multifunctional Handheld 3D Scanner, RN-113, Multifunctional Handheld 3D Scanner, Handheld 3D Scanner, 3D Scanner |