Secukey-LOGO

Secukey XK5 OSDP Reader

Secukey-XK5-OSDP-Reader-PRO

Introduction

It is a waterproof OSDP keypad reader, and also with Wiegand output, can read 125KHz EM card, HID card & 13.56MHz Mifare cards at the same time.

Features:

  • Waterproof, conforms to IP66
  • OSDP+ Wiegand, AES128 encryption
  • Card Type: 125KHz HID, EM & 13.56MHz Milare
  • Programmable Wiegand output
    • EM card: Wiegand 26-44 bits output (default: 26bits)
    • Milare card: Wiegand 26-44, 56, 58bits output (default: 34bits)
    • HID card: Wiegand 26-37 bits output
  • PIN output: 4 bits, 8 bits or virtual card number

Specifications

Secukey-XK5-OSDP-Reader- (16)

Installation

  • Drill 2 holes (A, C) on the wall for the screws and one hole (B) for the cable.
  • Knock the rubber bungs to the holes (A, C).
  • Fix the back cover on the wall with 2 screws.
  • Thread the cable through the cable hole (B).
  • Attach the unit to the back cover.

Secukey-XK5-OSDP-Reader- (1)

Wiring 

Color Function Notes
Red Power+ +12V
Black GND Ground
Green DO Datao
White D1 Data 1
Brown LED Green LED Light Control
Yellow Buzzer Buzzer Control
Blue A RS485A
Gray B RS485B

Connection Diagram

  • Connect with OSDP ControllerSecukey-XK5-OSDP-Reader- (3)
  • Connect with Wiegand ControllerSecukey-XK5-OSDP-Reader- (4)

Programming

Note: When enter program mode, need press ” for 5 seconds, then press Master code# (Factory default master code: 123456)

Set Master Code (6 digits)
The Master Code is used to prevent unauthorized access to the system, we highly recommend immediately updating it and recording the New Master Code.Secukey-XK5-OSDP-Reader- (5)

  • Set Wiegand Format for EM CardsSecukey-XK5-OSDP-Reader- (6)
  • Set Wiegand Format for HID CardsSecukey-XK5-OSDP-Reader- (7)
  • Set Wiegand Format for MIFARE CardsSecukey-XK5-OSDP-Reader- (8)
  • Set PIN Output FormatSecukey-XK5-OSDP-Reader- (9)
  • Set Keypad BacklitSecukey-XK5-OSDP-Reader- (10)
  • Baud Rate Settings (Factory default: 9600)Secukey-XK5-OSDP-Reader- (11)
    Note:
    The baud rate of all readers under the same controller should be set to the same with the controller’s baud rate, otherwise the connection will fail.
  • OSDP Address Settings (Factory default: 0)Secukey-XK5-OSDP-Reader- (12)
    Note: The addresses of all readers under the same controller should be set to be different, otherwise the two readers will conflict
  • Reset to Factory Default (two methods)
    • Method 1Secukey-XK5-OSDP-Reader- (13)
    • Method 2 (This way is suitable for users forget the master code):
      Power off, connect Yellow wire and GND wire, then power on, wait for 5 seconds, there will be a long beep, meas reset to factory default successfully, then disconnect the Yellow wire and GND wire.

Indicator light status

Secukey-XK5-OSDP-Reader- (14)

Packing List

Secukey-XK5-OSDP-Reader- (15)

Documents / Resources

Secukey XK5 OSDP Reader [pdf] User Manual
XK5 OSDP Reader, XK5, OSDP Reader, Reader

References

Leave a comment

Your email address will not be published. Required fields are marked *